Question about Whirlpool Ultimate Care II LSQ9549L Top Load Washer

1 Answer

Excess water in clothes after spin cycle

My whirlpool ultimate care II washer spin cycle does not remove the excess water from the clothes, The clothes is very wet after a regular wash cycle. There is noise during the spin cycle but it it is not spining

Posted by on

  • 1 more comment 
  • Iddybiddy Nov 11, 2008

    My washer spins like it should but my clothes are dripping wet after the spin cycle.

  • Anonymous Mar 23, 2014

    machine washes ok but not spinning water out of clothes

  • Anonymous Mar 23, 2014

    the washes ok but does not spin water out of the clothes

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 903 Answers

Unblock the outflow pipe from the machine that goes into the sump under the sink. (have a pot ready for water overflow) This will help drain the water. If the spin cycle is making a screetching sort of noise then it is possible that the carbon brushes will need changing. This affects the spinning if the brushes are worn.

Posted on Nov 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Whirlpool Ultimate Care II washer goes thru all cycles but will not spin, so clothes are wet. We replaced the motor coupler but will only spin without clothes. Once you put clothes in the tub does


sounds like direct drive gears are bad.. there is a slip coupling that goes over the shaft of the transmission adn assist turning the tub that could be worn or broken. you will have to remove the agitator and check the nut on top of the tub to see if it is tight or to remove the nut and check that coupling.

Dec 01, 2011 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

I have a whirlpool ultimate care 2 top load washer no spin


Sounds as if the drive hub which the tub is attached to maybe free spinning. Not an expensive part but does require a special tool called a spanner wrench to remove and replace.

Jan 31, 2010 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

I have a Whirlpool Ultimate Care II Washing Machine. Lately, the spin cycle does not remove all the water. How can I fix this? Thanks. Bill


The clothes are wet after spinning When the clothes are wet at the end of a cycle, check these: Motor coupler Spin cycle Siphoning Water-inlet valve Motor coupler To test the motor coupler, re-start the washer in its spin cycle. Let the machine run for a minute, and then open the lid and notice whether the tub is spinning: If it's spinning when you lift the lid, the coupler is fine. If it isn't spinning--and your machine was produced by Whirlpool®--you may have a broken coupler. Many Whirlpool-made washers use a small, relatively inexpensive device called a motor coupling. This plastic-and-rubber component is mounted to the shaft of the motor on one side, and to the transmission on the other. Over time, the coupler wears out and fails. When that happens, you need to replace it completely. Spin cycle If the washer doesn't reach its proper spin speed, the clothes may be too wet at the end of a cycle. Check to be sure the load is properly balanced and run a spin cycle again. If the clothes are still wet, you may have a worn or loose belt (Maytag®), a worn clutch (GE®/Hotpoint®), or a worn motor pulley or tub bearing. Replace the applicable component. Alternatively, there could be clothes caught between the inner and outer tubs. Read the "It spins but won't pump" section of the "It won't drain" section. Also, there could be other things that cause friction on the drive train. Seek the assistance of a qualified appliance repair technician. Siphoning If the water that pumps from the machine goes right back into the machine after the spin cycle, it may be because your washer is siphoning the water from a laundry tub with a slow drain, back into the washer. Try to improve the draining of the laundry tub. (Is there something stuck in the drain?) Also, be sure the drain hose doesn't reach more than about 4 inches into the laundry tub. If it does, cut off the excess. Water-inlet valve Water-inlet valves eventually fail. One problem that may develop with a water-inlet valve is that it can no longer completely shut off when the electricity is turned off to it. Then, the valve may leak and drip water into the clothes tub--you may notice that your washer has water in it when you haven't used it for a few days. To fix this, replace the valve.

Jan 09, 2010 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool Ultimate Care II LSQ8243HQ0 weak spin, wet clothes


if it has a belt, it may be slipping, but you would smell a bit of burning rubber.in high use times(4 to 8 pm), the current of electric supply is low, thus less power. third, motor may need to be replaced. plz rate-bozcro

Sep 10, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Spin cycle doesn't work


the motor coupling is bad it is between the motor and transmission

Jul 09, 2009 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

The spin cycle for my


Dear shelldon39, Fri 2-20-2009 9:24pm EST (USA)

Some machines will shut down during the spin cycle as a precaution to prevent damage!

They will do this if you overload the washer with clothes and/or use too much detergent!

If this doesn't help please get back to me with more details!

jack
1131431.jpg

Feb 21, 2009 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

The washer doesn't spin out the water. Clothes come out soaked?


if it washes ,,check your lid switch,,if it doesnt wash and spin check your motor coupling...onthejob

Jan 10, 2009 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

Whirl pool washer bangs when in spin cycle


if new did you remove shipping strap in back..the unit cant lean more than 2 degrees..make sure clothes are even in tub..try to wash clothes alike..

Dec 25, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Washer will not Spin during SPIN CYCLES


Thanks for the question If your washer sorta spins and washes ok, your problem is with the transmissionTHanks for your question THe Appliance doc

Jul 29, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

634 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...