Question about Jenn-Air JDB6510 Built-in Dishwasher

2 Answers

Does not advance to drain cycle

The machine runs. it fills and it washes but, It continues past the rinse and dry cycles. So when the dial reaches the end there is hot water standing in the base. I have removed the drain tube and it is clear. And once in a great while when I turn the dial to the rinse and hold cycle it will start the drain process but that does not happen in the normal cycle.

Posted by on

  • davesan1 Jan 10, 2008

    Timer correctly tries to start the drain cycle and/or wash cycle but pump will not run even though correcr voltage appears to be present on motor connector inputs. One motor connector input "MAIN" appears to be open circuit, suggesting motor needs replacing. Has anyone done this? Does it require any special tools? Anyone know the charge for having it replaced professionally?

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

I would bet that it is the timer switch assy.
Motor runs ? yes
washes? yes
drain tube clear ? yes

If there is no drain valve to deal with, the problem must be the contacts during the timer cycle, since the main obviously works or you wouldn't be able to wash anything.
you need a new timer switch assy.

Posted on Nov 20, 2008

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 125 Answers

You may find the problem in your garbage disposer and / or the passage opening to the dishwasher.

Posted on Aug 08, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Two year old Whirlpool washer started failing to advance from the rinse cycle to the spin cycle a couple of weeks ago. However, the water would drain through and run until you manually advanced the system...


Hi, I just want clarification. Is the washer filling to a point when it starts draining the water before it starts to agitate? If this is the case, check the end of your drain hose and make sure that it is as high as the top of the washer. Make sure that where it goes into the drain pipe that it is a loose fitting so that air will **** back into the drain hose. Please let me know if I have given you the right information or if I have missed what you are describing so I can assist you further.

Thank
Vic

Jul 13, 2009 | Washing Machines

1 Answer

Dishwasher stalls


If the cycle doesn't complete, check these:

Water-heating cycle
Timer
Water-heating cycle Many dishwashers heat the wash and/or rinse water to a higher temperature, as the cycle calls for it. In these cycles, the dishwasher pauses after it has filled with water, waiting for the water to reach the pre-set temperature. What happens next, depends, as follows:

  • On some units, the pause is timed and the unit continues after the allotted time.

  • On others, the cycle can't continue until the water reaches the higher temperature. If you have this type of dishwasher and the water isn't being heated (say, because of a problem with the heating element or thermostat), after the unit stops at the heating cycle, it never continues. When you repair the heating-system problem, the "cycle problem" is fixed too.

Timer Timers don't often fail. But if every other part of the dishwasher seems to be working properly and the timer knob seems to be stuck in one place--doing one function continuously--the timer may be at fault. Dishwasher timers can't be repaired. If yours is defective, replace it.


May 31, 2009 | Bosch SHU4006 Dishwasher

1 Answer

Washer will not advance in the rinse cycle,water just runs continuely.


check the drain hose it should be only 6 to 8 inch in your drain line if drain hose is all the way in the drain line correct it and you will be fine.

May 21, 2009 | Washing Machines

1 Answer

Kenmore front-load washer stops at rinse cycle


When the washer initially fills for the wash, is it only hot water entering the drum? Try switching the water temperature between hot and cold as it fills. If any of them show little or no water getting through, it sounds too easy but check to make sure water supply taps are on, and that the cold/hot fill hoses aren't reversed. Remove the fill hoses and check any of the screen filters for blockage (in the hoses and in the inlet water valve). When the machine stops and waits to fill but all you hear is a hum, it sounds like there is power going to the valve but water is not able to get through it.
Good luck!

Mar 03, 2009 | Kenmore 43142 Front Load Washer

2 Answers

Machine fills and agitates, but won't drain


Please empty your machine and run the machine empty. If the washer goes through the whole cycle without any clothes. Please let me know

Jan 19, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

New Whirlpool washer model WTW5700SW rinse cycle doesn't worker properly. The water never fills the tub & continues to drain. You have to manually move the dial to the end of the rinse cycle to have...


Sounds like what you are describing is the timer on the dial is not activating the next cycle. Timers are usually the problem when the cycles do not complete there cycle

Dec 03, 2017 | Whirlpool Washing Machines

1 Answer

Won't complete the cycle


Try using a quick cycle and see what happens. Don't use sanitize or any extra heat cycle. Sometimes during sanitize high temp rinse or other cycles the timer motor is stopped until the water heats up. The sensor could be defective. Not all machines do this and I'm not real familiar with your particular one.

Jul 03, 2008 | Bosch 24 in. SHU43 Built-in Dishwasher

1 Answer

Roper (Whirlpool) Washer


ohm out the lid switch, with the switch closed it should read contunity if it does not then the lid switch is the issue

Apr 19, 2008 | Roper RAB2121KW Top Load Washer

Not finding what you are looking for?
Jenn-Air JDB6510 Built-in Dishwasher Logo

374 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jenn-Air Dishwashers Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

John Tripp
John Tripp

Level 3 Expert

4655 Answers

Mike

Level 3 Expert

4354 Answers

Are you a Jenn-Air Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...