Question about HP Printers & Copiers

1 Answer

No information on how to print envelpoes on the C6280 All -in-One ...I know how to load envelopes in the in-tray , but when I click on "print" , the machine fails to do so .

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I sat up all night wading through pages of computer speak jargon - gobbledegook if you will ?!
Why can't you people you English ? Your convinced you do , but you don't !
Eventually I found the solution in Word . and I have now solved the problem . Simple when you know how .
However , I repeat for your information that the Basics Guide for the HP Photosmart C6280 All -in - One contains NO information on how to print envelopes except for the obvious on how to load the envelope/s into the feeder tray .

Thank you for getting back to me ,

Keith Kettlewell
Bristol

Posted on Nov 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Canon printer MX310 works fine, but I have never used before to print envelopes. Once i set it for a particular envelope, where do I insert the blank envelope. Have tried every conceivable...


canon.gifPrinting an Envelope

For details about how to load an envelope into the printer, see the user's manual.

The procedure for performing envelope printing is as follows:

1. Fold down the envelope flap.

2. When loading the envelope in the rear tray, orient the envelope so that the flap is on the left and the folded surface is facing down.

env_y_tray1.gif

3. Open the printer driver setup window, and select Envelope from the Media Type list on the Main tab.

envelope1.gif

4. Click the Page Setup tab, and select Youkei 4, Youkei 6, Comm. Env. #10, or DL Env. for Page Size.

5. Select Landscape for Orientation.

6. Click OK.

When you execute print, the information is printed on the envelope.

Jul 21, 2011 | Canon PIXMA MX310 All-In-One Printer

1 Answer

How do I print envelopes on Office Jet 6500?


  • Flip up the printer's output tray to reveal the input tray below and remove any paper in the input tray. Insert up to five envelopes into the input tray, print-side down, and slide the width guide so it touches the edges of the envelopes but does not bend them.

  • 2

    Fold the output tray back down and flip out the extension piece at the end of the tray. Fold up the paper stop at the end of the output tray's extension to keep the envelopes from falling out of the output tray.

  • 3

    Click "File" at the top of the software program you are using to create the text to be printed on the envelopes. Click the "Properties" or "Setup" button in the window that opens, then click on the tab labeled "Paper/Features."

  • 4

    Click the "Type Is" pull-down menu and select "Envelopes." Select the "Size Is" drop-down menu and click on the size of the envelopes you have loaded in the input tray. If you do not find the correct size, click "Custom" and type the height and width in the window that opens, then click "Save."

  • 5

    Click the "Source Is" drop-down menu and select "Tray 1." Click the "OK" button at the bottom of the window to save your settings, then click the "Print" button to begin the print job.



  • Read more: How to Print Envelopes With the HP 6500 E709A ' eHow.com http://www.ehow.com/how_7439186_print-envelopes-hp-6500-e709a.html#ixzz18tq0C0JF

    If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response. Happy Holidays!
    Thanks, Joe

    Dec 23, 2010 | HP Printers & Copiers

    1 Answer

    How does one print envelopes on the xerox pro 232?


    descicon.gif function showThisURL(){ $('.urldisplay').show(); } function hideThisURL(){ $('.urldisplay').hide(); } email-icon.gif print-icon.gif btn_remove_x.gif Return to Search Results Solutions for : How To Print on Envelopes in the Bypass Tray or Optional Envelope Tray Solution : Print on Envelopes in the Bypass Tray or Optional Envelope Tray This solution assumes that Number 10 envelopes are being used and printed on using Microsoft Word 2003 or 2007. Steps may vary if other applications are used.
    NOTE: If necessary, make sure the envelopes are loaded correctly in the Bypass or Optional Envelope Tray. See the Related Items below for additional information.
    From the computer using Word 2003:
    1. Open the application, and then select [Print] from the File menu. The Print window will be displayed.
    2. Select the required printer, and then click on [Close].
    3. Select [Envelopes and Labels] from the Tools menu. The Envelopes and Labels window will be displayed.

      NOTE: For Office 2003, click on [Tools], then [Letters and Mailings], and then select [Envelopes and Labels].

    4. Click on the [Envelope] tab.
    5. Enter the address and other information in the fields provided, and then click on [Options].
    6. Select [Size 10 (4 X 9.5)] from the Envelope size pull-down menu.
    7. Click on the [Printing Options] tab.
    8. Click on the second icon from the right under the For Feed Method section.
    9. Click on [Face-up].
    10. Select [Default Tray (automatically select)] from the Feed from pull-down menu.

      NOTE: If the Envelope Tray is being used, select [Tray 2].

    11. Click [OK].
    12. Click on [Print] to begin printing.
    From the computer using Word 2007:
    1. Open the application, and then select [Print] from the File menu. The Print window will be displayed.
    2. Select the required printer, and then click on [Close].
    3. Click on [Mailings] tab.
    4. Click on the [Envelopes] icon.
    5. Click on the [Envelopes] tab.
    6. Enter the address in the Delivery Address field.
    7. If necessary, enter the return address in the Return Address field.
    8. Click on the [Options] button.
    9. Click the [Envelope Options] tab.
    10. Select [Size 10] from the Envelope Size pull-down menu.
    11. Click the [Printing Options] tab.
    12. Click on the fifth icon from the left from the Feed Method section.
    13. Click on the [Face Up] radio button.
    14. Select [Bypass (Tray 5)] from the Feed From pull-down menu.
    15. Click [OK] twice.

    Nov 23, 2010 | Xerox Printers & Copiers

    1 Answer

    How do I print an envelope


    Hi,

    Step 1- Remove the output tray

    307daa9.jpg

    Step 2 : Load Envelopes

    To print one or more envelopes, follow these steps:

    1. Remove all paper from the paper tray, and then slide a stack of envelopes into the tray, with the envelope flaps up and to the left (print-side down), until they stop.

    2. Adjust the paper-width guide against the envelopes. Be careful not to bend the envelopes and do not overload the tray.

    c2987fe.jpg

    3. Adjust the paper settings in the Printer Properties dialog box for envelopes. Click the Paper/Quality tab, then select the following print settings:

    Size is: The appropriate envelope size
    Type is: Automatic or Plain paper

    4. Select any other print settings that you want, and then click OK .

    5. Print the envelopes.


    Regards,
    Riztech

    Mar 04, 2010 | HP OfficeJet 6210 All-In-One InkJet...

    1 Answer

    X1240 will not print envelope, prints all others just not envelope


    A) Check if you are loading the envelope correctly inthe tray ( load a maximun of 10 enveleopes into the paper support.
    Place the bottom of the envelope with the print side facing up.
    Squeeze and slide the paper guide to the top edge of the envelope.

    B) Make sure you select the paper size that matches your envelope:

    1. Make sure the All-In-One is turned on.
    2. Click File Print.
    3. From Print dialog box, click Properties, Preferences, Options, or Setup (depending on the program).
    4. The Print Properties dialog box appears
    5. From the Paper Setup tab, select the type (Envelope), paper size (your envelope's size) and orientation (landscape).
    This and more information is in the User's Guide you can download from LEXMARK (it is common to all 1200 series):
    http://www.lexmark.com/publications/eng/1200/index.html

    Aug 17, 2009 | Printers & Copiers

    1 Answer

    Paper jam when trying to print envelopes.


    You need to make sure that your print sriver setting match the setting on the printer itself.

    If setting are changed on the printer itself to envelopes then when you go to print click preferences button on print screen and look for a place to change paper type (usually defaulted to letter size.) Change paper type to envelpoes and click ok. Click ok again on print screen and it should print correctly.

    Paper types must be configured the same on the device as well as the print driver installed on the computer.

    Hope this helps
    TankMurdock

    Mar 09, 2009 | HP Photosmart D7260 Printer

    1 Answer

    How to print an envelop


    nstructions Use the following steps to ensure that you are ready to print envelopes. Your printer can have either a single envelope or multiple envelopes loaded and ready for printing.
    • If you are printing a single envelope, you can use the single envelope slot and leave your paper in the lower (IN) tray. This allows you to print the envelope and then a letter.
    • If you are printing a stack of envelopes, use the lower (IN) tray for loading the stack of envelopes.
    To Load a Single Envelope
    1. Do not remove the paper from the lower (IN) tray. Be sure the card guide is in the down position, before using the single envelope slot.
    2. Remove a single envelope from its packaging.
    3. Slide the envelope evenly into the single envelope slot. The single envelope slot is located on the right side of the upper (OUT) tray. The envelope should be loaded with the address side down (flap side up).
    4. Make sure the creased flap edge of the envelope aligns with the right side of the single envelope slot.
    5. Slide the envelope through the slot until it stops. Make sure the envelope is not bent and is straight in the envelope slot.
      NOTE: To minimize print skew, use envelopes with rectangular flaps rather than triangular flaps.
    To Load Multiple Envelopes
    1. Slide the paper width adjuster to its leftmost position.
    2. Pull out the paper length adjuster and remove any paper from the IN tray.
    3. Remove up to 20 envelopes from their packing and tap the short edge of the envelopes on a flat surface to even the stack.
    4. Slide the envelopes evenly into the IN tray, address side down (flap side up).
    5. Slide the paper width adjuster to the right until it gently touches the left edge of the envelope stack.
    6. For size Invitation A2 and C6 Envelopes, press the inside of the paper length adjuster handle to release and lower it.
    7. For all sizes of envelopes, push the paper length adjuster in toward the envelopes until it stops. Make sure the envelopes are flat in the lower tray and not bent.
    Set up the Printer Properties
    1. Select Start on the taskbar. Choose Settings, then Printers. Right-click the printer. Select Properties from the pop-up menu.
    2. Select the Paper or Setup tab depending on the version of the printer driver software.
    3. In the Paper Options section, select the desired envelope size from the Paper Size drop-down box.
    4. Click OK.
    Print Print the envelope from your chosen program. From most applications, just select the File menu, then choose Print. After Printing the Envelopes Reset the printer and the printer properties for the kind of printing you will be doing next.
    1. Remove any remaining envelopes from the lower (IN) tray.
    2. Slide the paper width adjuster to its leftmost position.
    3. Load the desired paper into the lower (IN) tray.
    4. On the computer, Select Start on the taskbar. Choose Settings, then Printers. Right-click the printer. Select Properties from the pop-up menu.
    5. Select the Paper or Setup tab depending on the version of the printer driver software.
    6. In the Paper Options section, select the desired paper size from the Paper Size drop-down box.
    7. Click OK.

    Jan 19, 2009 | HP LaserJet 1600 Printer

    2 Answers

    HHow do I print envelopes on a deskjet940c. What is the set up.


    Here is a how-to for the printer, but I'm not sure if you mean the printer, or in a program.
    If this is not what you need, let me know.

    HP Deskjet 920c and 940c Series Printers - Printing Envelopes s.gif s.gif s.gif

    gtabseps.gif
    gtabblt.gif Loading a single envelope gtabblt.gif Loading multiple envelopes gtabseps.gif Loading a single envelope Preparing to print
    1. Place the envelope, with the flap side on the left and facing up, into the single envelope slot.
    2. Push the envelope forward until it stops. See Figure 1.
    Figure 1: Inserting the envelope c00104463.jpg Printing guidelines
    • Verify that the Out tray is in the down position.
    • Avoid using envelopes that have clasps or windows.
    • Avoid using envelopes that are shiny or embossed, envelopes with thick, irregular, or curled edges, or envelopes that are wrinkled, torn, or otherwise damaged.
    Loading multiple envelopes Preparing to print
    1. Pull out the In tray.
    2. Slide out both paper guides and remove all paper from the tray.
    3. Place no more than 15 envelopes -- with the flap side on the left and facing up -- in the tray.
    4. Push the envelopes forward until they stop.
    5. Slide the paper guides snugly against the edges of the envelopes, then push the tray forward until it stops. See Figure 2.
    Figure 2: Inserting multiple envelopes c00104464.jpg Printing the envelopes Each software program is different and requires different steps to successfully print envelopes. For instance, in many versions of MS Word, clicking Tools , and then Envelopes and Labels , accesses the envelope-printing feature. Other software programs will differ from this procedure. Consult the Help menu on a software program or User's Guide for instructions for the particular application. Printing guidelines
    • Never place more than 15 envelopes in the In tray at one time.
    • Align the envelope edges before inserting them.
    • Avoid using envelopes that have clasps or windows.
    • Avoid using envelopes that are shiny or embossed, envelopes with thick, irregular, or curled edges, or envelopes that are wrinkled, torn, or otherwise damaged.

    May 27, 2008 | HP Printers & Copiers

    3 Answers

    Can't print envelopes


    Solution Title: How to print on COM10 envelops from the Bypass tray (PCL6) using a Windows 2000 O/S Resolution/
    Solution
    thumbsup.gif Fixed! thumbsdn.gif Did not fix. Resolution Role: Fix
    Critical Message: The Envelope must be placed in the Bypass Tray face down (flap side up) and Long Edge IN. In Microsoft Word (Word 2000)
      1. Under the Tools tab, select Envelopes and Labels.
      2. Enter your Delivery and Return addresses.
      3. Click on Options
      4. Under Envelope Options; [Envelope size], select Size 10 (41/8 x 91/2 in)
      5. Under Printing Options, select Portrait (LEF) - Long Edge Feed
          • As Feed from, select Tray 5 (Bypass)
      6. Click <OK>

    Within the WorkCentre Pro 123/128 print driver
    After opening up the print driver [<Start>, <Settings>, <Printers>, double-click on the WCP 128 PCL6 driver], click on Printing Preferences under the General tab.
    • Under the Paper/Output tab
    Set the following features as follow:
      • Job Type: Normal Print
      • Paper Size: COM10
      • Output Size: Same as Paper Size
      • Image orientation: Portrait
      • Image Rotation: OFF
      • 2 sided Print: 1 sided Print
      • Stapling: None
      • Output destination: Center Output Tray
      • Offset Stacking: None

    • Under Tray/Layout
    • Set Paper Source to Tray 5 (Bypass)
    • Click on Bypass Tray Settings
      • Paper Type: Heavyweight (1 or 2)
      • Feed orientation: Portrait
    • Click <OK>
    • " on Specify Paper Type and select Heavyweight (1 or 2)
    • " (Apply> and <OK>
    • " <OK> again

    In Microsoft Word under Envelopes and Labels, Click <Print> to send the information to the printer.

    Note: This setup represents one way of printing envelopes. Other ways setting up some features in a different manner will work as well.

    Solution v1.3.20.0 312637.How to Print on COM10 Envelops From the Bypass Tray (PCL6) 2006-04-05 21:57:29

    Nov 02, 2007 | Xerox WorkCentre PRO 128 Copier

    Not finding what you are looking for?
    Printers & Copiers Logo

    Related Topics:

    87 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top HP Printers & Copiers Experts

    kakima

    Level 3 Expert

    96396 Answers

    k24674

    Level 3 Expert

    7987 Answers

    Brian Sullivan
    Brian Sullivan

    Level 3 Expert

    27725 Answers

    Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...