Question about RCA VR557 VHS VCR

1 Answer

Remote control codes

I want to set up my vcr.but i dont have the codes for the remote to work,can you give me the vcr codes?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

RCA Universal Remote Control Programming Codes
The remote may already be set up to operate your brand of TV, VCR, or Cable Box. It is pre-programmed with following codes:

  • TV-000
  • VCR-000
  • Cable Box-000
  • AUX is programmed with VCR code 037
Programming a Device using Code Search:


  1. Manually turn ON your device (TV, VCR, Cable Box)
  2. Press and "HOLD" CODE SEARCH
  3. Press and release the device button you want to set up (TV, VCR, Cable Box) However, if you are using AUX for a device, press and release AUX first and then the device button for the type of device to be programmed (TV, VCR, or Cable). The selected device button will flash once.
  4. Release CODE SEARCH.
  5. Press OFF/ON repeatedly until the device turns off (you may have to press up to 100 times at a rate of once per second).
  6. Once the device turns off, press and release ENTER.
  7. With the device on, press any other button. If the device responds, no further programming is required. If the device does not respond, repeat steps 1-6.

Programming a device using the Code Lists:
Find codes for device and brand below.
  1. Press and "HOLD" CODE SEARCH.
  2. Press and release the TV, VCR or Cable button you want to set up. If programming AUX for a device, press and release AUX first and then the device to be programmed (TV, VCR or Cable). When the selected device button flashes proceed to the next step.
  3. Enter the three digit code from the TV, VCR or Cable Box code lists.

  4. Release CODE SEARCH.
  5. With the device on, press another button, for example CHANNEL UP. If the device responds, no further programming is required. If the device does not respond, repeat steps 1-5 using another code number from the lists.
RCA Codes for VCR
000,005,007,008,028
035,037,054,069

Posted on Mar 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change channels on a VCR without the remote?


You should have a remote control to change channels. If you wish to buy its original remote control, contact the authorized service centre, or authorized dealer to your device brand. They can either give you a genuine remote control to your device, or can direct you, from where can you purchase a suitable one.
To select a proper universal remote control, you should know about the number of digits to its set-up codes. There are 3 digit, 4 digit, 5 digit, 2 digit and even single digit codes, to some brand devices. After confirming this, check the sites linked here. Both the sites have set-up code list and set-up procedure to many popular brand remote controls. Check which brand remote control has set-up code/s to your device brand, and buy that one according to availability? Brand name of the remote control isn't a matter, but it should have set-up codes in its code list, to the device brand you have.
Please note: Every new universal remote control will have set-up code list, and set-up procedure along with its pack. Never accept a remote control, that hasn't both of this. For more details about the set-up codes, visit the site http://electrohelponline.blogspot.com/ Check this site too. http://remotesearch.blogspot.com/ Universal remote controls are available at most of the electronic spare part selling shops.

Sep 13, 2014 | Televison & Video

2 Answers

I need to program a VA-405 universal remote to work with a toshiba television. None of the codes in the user's manual worked.


i have sony tv and i am trying to set it up but i dont have the user's manual .
i dont remimer have to set it up and i dont have the code number

Mar 06, 2012 | Televison & Video

1 Answer

I need to set a 'One For All' Remote control,and I need the 3 digit product code, so I can make the control work.. The model # is VR5000A Thank You


One For All remote manuals and code lists are available here: http://www.oneforall.com/support/manual . Which specific remote do you have?

Most of the One-For-All remotes use a 4 digit code. The only one, URC-2005, that has 3 digit codes (of the ones I located) gives Orion VCR codes of 036, 088, 121, 208, 209 .

Note: remotes are limited to having codes for devices released at least 6 months before the remote was programmed. If your VCR is newer than the remote, you may need a new remote.

I hope this helps.

Cindy Wells

Jun 22, 2011 | Orion VR213 VHS VCR

1 Answer

I don't know the code to my Panasonic VCR


Hello;

According to the manual located at
http://www.hifi-remote.com/manuals/manual.shtml?URC-3300 , the codes for a Panasonic VCR are: 0035, 0162, 0225, 0454, 0616, 1062, 1162, 1262.

If none of these codes work, you can find the code for your VCR by doing the following:

1. On the remote control, press VCR once.
2. Press and hold SET until the LED blinks twice, then release SET.
3. Enter 9 - 9 - 1.The LED will blink twice.
4. Aim the remote control at the the VCR and slowly alternate between pressing POWER and VCR. Stop when the VCR turns off.
NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first.
5. To lock in the code, press and hold SET until the LED blinks twice, then release SET.

Hope this gives you the information you need.

Mar 14, 2011 | One For All URC-3300 Remote Control

1 Answer

I am looking for the VCR Codes for a Hitachi VCR on your remote. Could you please give me the code to program my VCR?


The One-For-All code list gives:
standalone Hitachi VCR: 0000 0042 0041
Hitachi TV/VCR combination unit: 0000

See the following page for the full code list: http://oneforall-na.com/remote.php?type=URC4220 and look for the codes link near the bottom of the page.

If your device was built within 6 months before the remote was programmed or is newer than the universal remote, the codes may not work. If this remote allows, try scanning through all the codes. However, if it still doesn't work, you need a newer universal remote, a universal remote that can be programmed from a computer or an exact or substitute replacement remote for the device. Search remotes.com for a replacement remote - use the model and not the manufacturer for the best chance of finding the remote.

I hope this helps.

Cindy Wells

Sep 18, 2010 | One For All URC4220 Remote Control

1 Answer

NEED CODES TO USE WITH ONE FOR ALL UNIV. REMOTE URC3300


Try holding down the tv power button and keep holding it while you press the channel button until your tv comes in.. It takes a few pushes. Make sure your tv is off first though.

May 09, 2009 | Televison & Video

1 Answer

I have a panasonic DMR-ES46V vcr/dvd HDMI i lost the instruction manuel and need to reset the remote to work agin i dont have the codes to do so all the display says is set 1 and the remote dosnt work


1) Hold The Enter Button Down On The Remote
2) Press And Hold The Numeric Button "1" For About 3-4 Seconds
3) Your Remote Is Now Reset To The Remote Control Code #1 (Default Setting)

Apr 27, 2009 | Panasonic DMR-EZ47V DVD Recorder/VCR

1 Answer

Cant get my universal remote to work my Zenith model TVBR1922


ha i can help a little ,i also have a rca universal and same tv,vcr combo,the codes in the list rca provides
do not work ,but if you go through the code search procedure componet vcr,until the set turns off
hit enter,this will allow for power on off funtions and ch up down or number keys,also vcr functions,
but no vol, control or menu nevigation,hope this helps a little

Jan 08, 2009 | Zenith TVBR1922 19 in. Combo

1 Answer

Jensen JR400


Code For Model JER422
Code 3168 for Sansui DVD Code 3401 for Sansui DVD Code For Model JER422
Code 2010 for Sansui VCR Code 2031 for Sansui VCR Code 2111 for Sansui VCR Code 2123 for Sansui VCR Code 2130 for Sansui VCRif these dont work try
http://remotefinder.rca.com/

and if you cant find one there then your remote does not support this device.

Dec 24, 2007 | Jensen JER-422 Universal Remote Control

Not finding what you are looking for?
RCA VR557 VHS VCR Logo

Related Topics:

1,025 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

70943 Answers

matt martin
matt martin

Level 3 Expert

1207 Answers

Jaime Hernandez

Level 3 Expert

2270 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...