Question about JVC AV-36F702 36" TV

1 Answer

Jvc tv the on timer button is on. unplugged to 48 hours plug back in and it sounds like it comes on and then shuts off and the time button is blinking. I have electronic experience, pls help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 337 Answers
Re: jvc tv

You need to check the horizontal output transistor first for a short,ift he transistor is good check the diodes and low value resistors of the secondary of the flyback(output trasformer),if all those are ok check the crt board,it has low value resistor for the g2 voltage,if ok you need to go back to power supply and check for a short from each one of the diodes to ground for a posiblwe short.Be careful when measuring voltages and use the correct ground.

Posted on Oct 02, 2006

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

TV won't come back after pushing wrong button on remote.

Try unplugging the TV.. After you plug it back in it may be OK. I had a similar problem were I could not turn on the TV (JVC). The owners manual specified in the troubleshooting section to unplug for 1/2 hour. I left it unplugged overnight and the next day plugged it in and it was fine.

May 21, 2013 | Standard (CRT) Televisions

1 Answer

The TV shuts off automatically and the Timer On button on the front of the TV flashes. The TV will not start again, either manually on the TV or with the remote. If we unplug the TV, leave it off for a few...

sound like timer setting on . you need to go to setup menu the timer set it off, if not , you need to check power supply unit, high value capacitor if under reading replace it. good luck!

Jan 27, 2010 | JVC AV-32230 32" TV

1 Answer

Sleep timer will not shut off We can not turn it on to shut it off.

unplug for a quite few hours, press and hold power button for 5 full seconds while it is shut off, then wait half hour more and plug back in and it should reset itself.

Jan 22, 2010 | JVC AV-27D203 27" TV

1 Answer

I was playing a game and it made a sound then shut off now my on timer light is blinking. when i unplug and plug back in the timer light stops blinking for a second then starts again.

Something shorted in the set, possibly the horizontal output transistor or a power supply diode. The reason it starts blinking again after plug in is because JVC try to come back on if they were on when the problem started. In other words, if it quit while it was playing it will always be in the on position until the problem is repaired and it can be turned off normally. Have a shop check it out for you. There are a lot of things that can cause one to go out. Thanks

Nov 01, 2009 | JVC AV-27020 TV

2 Answers

How do i shut off the timer on my jvc tv

HI...I have the same problem and I am trying this today (Expert advice on forum) ... Hope it works!

Try unplugging the power cord of your T.V. for 1-4 hours for a "HARD RE-SET".
If T.V. does not work normally after this, then you'll need parts/repiars. (Internal circuit/voltage problem).

Best of Luck!
I will know if it works for me in about 2 hours!

Mar 22, 2009 | JVC AV-27530 27" TV

1 Answer

Av-32d302 tv

The set is shutting down because a problem has been detected. Replacing the remote will not help. Count the flashes and call a JVC servicer to get an idea about what the specific problem may be.


Jul 29, 2008 | JVC AV-32D302 TV

1 Answer

JVC TV crisis.....HELP

yes... i actually work at verizon the tv is to old for fios because fios is so advanced we run off ot 720 to 1080 depending on areas. what kind of box is it? is it the hd box or stb>

Feb 13, 2008 | JVC AV-32230 32" TV

2 Answers

JVC tv "stuck" on sleep timer

I think you would have to turn off the sleep timer mode completely or increase its ON time span, say to 4 hours or so
or the lenth of time you have the TV on for. If that does not fix it then it sounds like a STANDBY MODE fault problem.
Hope this helps.

Feb 06, 2008 | JVC AV-27320 27" TV

2 Answers

Jvc av-32fa44 television

My JVC AV-32FA44 wont turn on. the on timer light blinks. When i unplug it and plug it back in i get beeping (i stoped counting at 50 beeps) then it stops and the light just blinks.

Jan 12, 2007 | JVC AV-32FA44 32" TV

Not finding what you are looking for?
JVC AV-36F702 36" TV Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

66623 Answers

matt martin
matt martin

Level 3 Expert

1187 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Are you a JVC Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides