Question about Audio & Video Receivers

1 Answer

Can you get a belt clip for the thomson rt 222?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Thanks
found one

Posted on Nov 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Thomson freeview remote control not working changed batteries but no lights on remote when we press the buttons


Double check that the batteries are installed correctly. It happens. Try a new set of batteries. Make sure the terminals are clean. A pencil eraser can clean them up for you. If all that fails I would have to wonder if a defect may have occurred. Good luck.

Mar 06, 2011 | Thomson Audio & Video Receivers

2 Answers

Hi, I have a JVC AL-E11BK fully automatic turntable. I need to replace the belt. Could you please advice me on how to do it? I cannot lift the platter because of the centre clip. I don't know what to do...


remove rubber pladder and use a flat blade screwdriver to remove the clip "carefull it may take off on you" next slide off the pladder, remove the old belt. Now! take the new belt put it around the inner part of the pladder, next put the pladder partly back on the center spindle and rotate until one hole lines up with the motor, take a hook and slip it under belt now carefully stretch over to the motor put on and push pladder into place and rotate it by hand clockwise to make sure it is in place, next reseat rubber pladder back on and power up to make sure it is working before replace the clip.

Feb 14, 2011 | Audio & Video Receivers

1 Answer

The rubber drive belt on my new Akai ATT021A USB Turntable has come off both spindles, and dissappeared under the platter.Can anyone recommend how it can be refitted. PaulR


Remove mat from platter. Using a small screwdriver remove the cir-clip holding the platter on, careful here mind your eyes it may spring away. Carefully lift the platter of, not too much force, you will see the belt laying underneath. Take the belt and put it around the underside of the platter, you will see where it goes, just on the large inside edge. Put the platter back on but not the cir-clip yet. Move the platter around until you can see the motor spindle. Using a small screwdriver and your finger put the belt onto the motor spindle. Make sure it is not twisted. Test the player if the turntable spins OK replace the cir-clip, this can be tricky but get it located first then lift the back up to clear the spindle bearing. There you go.

Jan 26, 2011 | Audio & Video Receivers

1 Answer

I Have a Thomson DPL2000 receiver, there is no sound and the speaker symbols are flashing can you help please


hi.... you have the solution for your problem? i have the same problem and i cant find the answer...can you help me?
my e-mail: scdetm@yahoo.es

Sep 19, 2010 | Thomson Audio & Video Receivers

1 Answer

The drive belt off my AWA turntable has come off and I cannot re-configure it


undo clip on centre of deck circlip normally (round clip) remove deck platter round plastic that records sit on...when removed turn over replace drive belt if brokern . if just come of place belt around the inner circle so there are no twists etc on the belt ....look at near outer edge of platter there is a clip you can stretch belt to to hold so you can put over drive motor...(belt stretch from centre to clip creating v with the bely as you veiw from above ..locate motor on the deck noe alifn top of v with positin above motor .. when done drop down platter onto centre shaft again.gently turn the platter clock wise until belt locates correctly with deck ..replace clip and test ..if ok done ..if not repeat until you get it right....sometimes over time belts stretch so a new belt may be required ..ebay can supply most belts . type in turntable drive belt ..measur size of belt by cutting is it..(if strectched and no use) measure lenght of belt find replacement belt that is smaller than measurment .i.e nearest size ...hope this helps yammandan

Aug 19, 2010 | Audio & Video Receivers

1 Answer

How can I get the Thomson EH308 drivers?


Please spend Thomson video converter on e-mail kukom6@hotmail.com Thanks :)

May 01, 2010 | Thomson Scenium DPL4000

1 Answer

Need a manual for rca rt 2500 receiver,don't know how to program radio stations manually can u help me thanks Darryl


Did you try "PAC PARTS"? But I think RCA stopped selling parts! Might try a search with the model#...

Apr 23, 2010 | Audio & Video Receivers

1 Answer

User manual


www.thomson.user-manuals.com

Jan 17, 2008 | Audio & Video Receivers

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68323 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...