Question about Rinnai Toyostove Direct Vent Heater: Laser 30 Toyostove Direct Vent Heater Shipping

3 Answers

Monitor Heater 41

When you try to turn on Monitor it will read E-01. What does that mean?

Posted by on

  • Anonymous Dec 06, 2008

    I have the same problem! Help!! :(


3 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

A grounded flame rod, could have a piece of soot on the flame rod, or a pinched wire. Be careful with gaskets when removing and they are reusable, but should be replaced if compromised in any way.

Posted on Jan 27, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 126 Answers

You have a grounded flame rod. Carbon on the rod or burner could be the cause. You could try to remove the rod and clean it. If you do you will need to have a gasket to seal it up when you put it back together. It is very important to seal Monitor heaters after repair. Monitor 41 heaters could be 20+ years old. If it has never been serviced, it's long over due.

Tom Hawkins

Posted on Jan 09, 2009

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 3 Answers

Our monitor heater was reading E-01. We decided that we would try cleaning the back of the unit and we landed up cleaning all parts of the unit that were visible. We plugged it back in and it works fine again. Thank you for your time.

Posted on Nov 04, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

When i turn on my monitor it read E-08. What does that mean?

If it's a Toyo stove it means blower motor. It may just need cleaned or might need to be replaced.

Mar 05, 2011 | Rinnai Toyostove Direct Vent Heater: Laser...

1 Answer

MPI 41 Keresene Monitor Heater LIft Pump over-primed?

I recently relocated monitor heater from living room to dining room and ran new line to heater. I have pressed the priming button located on right side and turn unit on, but all that happens is it will click on run for a cycle and burner never ignites and then turns itself off and burner indicator lights continue to blink on and off, I dont think it is getting proper fuel to unit. What do I need to do?

Jan 05, 2010 | Heating & Cooling

1 Answer

Monitor 41 heater not getting fuel

The problem would be in the inducer or combustion motor not starting up and running. This is a safety or one of several in you're system. When the fan comes on, the draft sends air to a switch telling you're unit that fan is on and ready to fire up.If the fan fails, no heat.Check for voltage to the fan motor. Even though it is free doesn't mean that it will work anymore.If there is no power to the motor, on a call for heat, you need to look at the schematic and find out where this motor gets its power. If there is power, remove it and try and find a dealer online or near by to where you can get one.It has to be working. I am surprised the burners come on at all.
Good Luck Wayne, and please let me know what you find out. Sincerely, Shastalaker7

Nov 05, 2009 | Goodman GMS90703BXA Heater

1 Answer

Monitor 41 oil heater stove lost its heat...

We repair Monitor Heater main circuit board and push button panel. call me at 800-782-4449 ask for Dima

Feb 01, 2009 | Heating & Cooling

1 Answer

Monitor 41 20 years old rebuilt 3 years ago. out of fuel

Hope you got this fixed. Sounds like you were having fuel flow problem.

Jan 17, 2009 | Rinnai Toyostove Direct Vent Heater: Laser...

2 Answers

Monitor heater model 41 keeps turning off during cold spells (AK)

Can you give us more info? How long does it run before quitting? Have you ever been close when it quits? Do you hear a thumping noise when it quits. Can you see the flame?

Tom Hawkins

Jan 07, 2009 | Heating & Cooling

5 Answers

MPI kerosene Monitor Heater

need to bleed air out of filter at oil tank crack open the screw on top it will bleed out air wait until oil starts to run out then tighten back and bleed at heater on right side lever inside hole push and let off slow 4-5 times and restart

Nov 02, 2008 | Rinnai Toyostove Direct Vent Heater: Laser...

13 Answers

Operating manual for MPI monitor heater

You can obtain an electronic copy of the 441 owner's manual from

Scroll towards the bottom of the page to find the 441 or 442 manuals.

Jan 09, 2008 | Heating & Cooling

Not finding what you are looking for?
Rinnai Toyostove Direct Vent Heater: Laser 30 Toyostove Direct Vent Heater Shipping Logo

1,377 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rinnai Heating & Cooling Experts


Level 3 Expert

2046 Answers


Level 1 Expert

53 Answers

Kenneth Wilson
Kenneth Wilson

Level 1 Expert

45 Answers

Are you a Rinnai Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides