Question about Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

1 Answer

Fisher and Paykel Dishdrawer beeping constantly

Hello, my top dishdrawer just started beeping and flashing the screen every 2 seconds while it wasn't being used. It is set to rinse but the screen cycles between showing the rinse screen, and illuminating the whole panel. Inside the rinse light is on and then it goes off in time with the 2 second cycle. I tried resetting at the wall - no good, it just starts up again. Opening the dwawer doesn't stop it either, and the power button just cuts off the cycle as it starts but it still cycles. It is driving me batty! Any suggestions greatly appreciated.

Posted by on

  • Champs1 Nov 04, 2008

    There is no service manual in the enclosure however if someone has a copy I would greatly appreciate an emailed copy.

    An update on the fault - The top drawer is doing the start up 4 rising beeps while showing the last used cycle on the LCD, and then shutting off. A second later it repeats the same thing again, and again, and again.... It won't take any button inputs and only turning the power off at the wall stops it. This all began while the dishwasher hadn't been used for many hours. The bottom drawer works fine.

    Help please!


×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Fisher and P... Master
  • 2,651 Answers

Leave it unpluged to stop for now, the machine has detected a leak and is constantly running hte pumps within the drawers to try to remove any water.. problrm is the water detector is in bottom under the lower drawer and htere is no pump to remove that water ..canbge a fickle machine as far as leaks are concerned, but the easy reason is usually misloading of the drawer itself, was an item put in that was too tall , preventing the lid from coming down and sealing off drawer causing water to overflow down the side??? there should be(so logn as no previous repairmen have taken it) a tech/trubleshooing guide taped to teh back wall behind the lower drawer, which is easily removed by unlocking hte hinges on either side of the front of drawer, explained in your manual

Posted on Nov 03, 2008

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
RescueTech
  • 145 Answers

SOURCE: current service manual for the Fisher & Paykel DD603SS dishdrawer

I realize this is an older post but for information's sake in case someone happens across this subject, you can get the manual for a DD603 series dishdrawer here:
http://www.fisherpaykelparts.net/index.php?categoryid=115&productid=18

Posted on Dec 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fisher and Paykel twin dishdrawer


there is water in the base setting off the flood sensor, you will need to remove the bottom draw and dry the water up with a towel (make sure the power is off and unplug it from the power point) then you will need to do a bit of testing to locate the cause of the leak, if your lucky the leak was caused by incorrect dish stacking or something too big in the draw

Jan 02, 2017 | Fisher and Paykel Dishwashers

1 Answer

How do you set the minutes on the clock?


There are two ways to set the clock on your coffee maker. 1- When you initially plug in the coffee maker, the unit will beep and "12:00" will flash on the LCD display for a few seconds. Press immediately the h/min button (o) to set the current hour. If "12:00" starts to flash, press the PROG button (n) for a few seconds until the "12:00" flashes again. Then press the h/min button (o) to set the current hour. There are AM and PM indicators on the top right side of the LCD screen. To set the current minutes, press the PROG button (n) and then press the h/min button (o) until the correct minutes appear on the LCD display. After 5 seconds, the unit will beep and the time will stop flashing. 2- At any other time, you can set the clock or change the set time by pressing and holding the h/min button (o). The unit will beep and "12:00" will flash on the LCD display. Use the h/min button (o) to set the current hour. There are AM and PM indicators on the top right side of the LCD screen. To set the current minutes, press the PROG button (n) and then press the h/min button (o) until the correct minutes appear on the LCD display. After 5 seconds, the unit will beep and the time will stop flashing. Notes: Your clock has now been set and will continue to keep the correct time, even after the coffee maker has been shut off. Unplugging the coffee maker or a power failure will reset the clock to 12:00 AM. Repeat the instructions above to reset the clock

Source : Krupsusa.com
Link to manual : http://product-support.groupeseb.co.uk/Download/Pdf/366/km730

Mar 21, 2016 | Krups KM730D Breakfast Set Coffee Maker...

1 Answer

F 2 on fisher paykel


http://www.fisherpaykel.com/vault/pdfs//pdf_usecares/590199D%20DishDrawerP7%20userguide%20USCANZAUGBIE.pdf

More then likely you will have to remove both drive impellers and give them a good clean as well as the stainless strainers . Every month or so I run a rinse cycle through them with a cup of white vinegar . this also helps with the damp smell in the warmer weather.
Good luck

May 04, 2014 | Fisher Paykel Fisher & Paykel DishDrawer...

1 Answer

Dishwasher keep beeping F1 and F5


F5 is the fast and rinse LED
It simply means the lid motror current is to high during the start - The lid is jammed up or down. Or the electronic controller has failed!!

Dec 29, 2013 | Fisher and Paykel DishDrawer DS605FDSM...

1 Answer

Dishdrawer cannot open


the power board at the base of the dishwasher under bottom drawer appears to have blown up. Take the bottom drawer out carefully to access the power board. Make sure the mains power is turned off.

The reason the bottom drawer is not getting back in is that lid seal actuators are stuck as the motors are in close position. Will reset to normal position once the power is restored. So don't try to push the drawer in as the lid seal will be damaged.

Feb 15, 2013 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

How do i change display color?


Hold the top left button down until you hear a beep and the seconds start to flash. Then push the bottom left button (7 times) until COL starts to flash above the seconds. At this point, you can use the 2 right buttons to scroll through the color options. When you're done, press the top left button to set and lock the color you've chosen. Hope that helps.

Dec 20, 2010 | Casio G-Shock G3110-1V Wrist Watch

1 Answer

Hey got a set of dishdraws and when ever we turn on it starts beeping and flashing F1


F1 Error is the Flood Switch. This Usualy mens there is a leak that has Triped the flote switch.

There are many things that could be leaking to cause this.

You should have a pro look at this machine.

Aug 11, 2010 | Fisher and Paykel DishDrawer DS605FDSM...

1 Answer

Our F&P DD601V2 double dishdraw is showing error 'U3' and the water does not totally drain out after a cycle, any ideas? Thanks


This applies to all DD601 and DD603 dishdrawers.
U3 is either one of the following:
- Drain pump is blocked.
- Drain hose is blocked.
- Sprayarm or rotor not turning freely.
- Motor electronics have failed.
- Machine set to 'LP' on a high pressure water supply.

Often it's just the last one, "Machine set to 'LP' on a high pressure water supply.", as this can be unintentionally changed by a user from an uncommon course of events. Sometimes, due to the technical design of the way the buttons work, if water bridges the 2 "Programme" and "Eco" buttons (inside on the top right of the tub), pressing either one, or both, (or just having your finger in the water) for longer than 5 seconds brings up a special mode that a user, in their ignorant attempts to get out of it, can erroneously change the pressure setting, subsequently causing a U3 error. It happened to me once when I was cleaning the machine, wiping around the Programme buttons.

To change to the proper High or Low Pressure settings:
1) LCD Display on. Hold the Programme and Eco touch switches simultaneously for 5 seconds.
2) Machine beeps and "HP" or "LP" is displayed in the LCD.
3) Push the Start/Pause button to toggle between them.
4) Push the Power button when correct selection complete.

Apr 07, 2010 | Fisher and Paykel 24 in. DD603H W Built-in...

1 Answer

Dishdrawer leaves dried detergent and crud on


1-Go to diagnostic mode.
2-Press the Start /pause button until you get the display rd for Rinse Aid Dispense setting.
3-Have warm water readu in a kettle or a pitch.
open thedispenser to pull water in.
press the Lock button to turn the dispenser on.
4-Continue to pull water onto the dispenser holder so it can flush out all the resisdue.
5-When you feel that it is enough, press the Lock button again tostop it.
6-Press the power button to get out of this mode.
7-Start a Rinse cycle to completely flush out the residue from the inner tube to the sewage.
8 The next run you won't see the white stuff anymore providing that you will use the liquid not the powder...

Jul 03, 2009 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

Kenmore Oasis Elite---110-27086601


This error only shows in diagnostic mode, with power off choose any buttons except stop and power, press in intervals 5 seconds on and 5 seconds off until 88 appears and all light light up. If the user panel is faulted F 2 will flash in the display, press the same button you used to start diagnostics to jump to the next error code and once through 88 will flash and diagnostics will start. Sometimes once F2 flashes and the machine has not been repaired it will stick at that mode.

Aug 07, 2008 | Kenmore Oasis HE 27082 Top Load Washer

Not finding what you are looking for?
Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher Logo

12,365 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Dishwashers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Mark Davis

Level 1 Expert

18 Answers

Bruce Denton

Level 2 Expert

273 Answers

Are you a Fisher and Paykel Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...