Question about Uniden Cordless Phone

Open Question

Area code not showing up with local numbers

Every time a local number shows up on the caller ID it's only seven numbers. It's suppose to be ten numbers.I've tried programming the area code, but that does not work.

Posted by on

6 Suggested Answers

SOURCE: Uniden CallerID not working..

sell it off

Posted on Jun 17, 2007


  • 146 Answers

SOURCE: area code

Here is a link to the site containing a pdf manual link and this is an excerpt for you :

Long Distance calls and Area Code Setting/Cancellation
While the present Caller ID information is displayed, pressing */tone/< will place
or remove the prefix "1" in the display to set the call for a long distance call, or
pressing #/> will set or cancel an area code (see page 30).
Storing Caller ID messages in the Phonebook
Messages shown in the Caller ID list can be stored in the phonebook. The phone
number and name of the party on the Caller ID list can be stored in memory.
1) When the phone is in standby mode, select the Caller ID message to be stored.
Then press the STORE soft key on the base or the EDIT soft key on the handset.
From the handset, then select E D I T ?. S t o r e / E d i t N a m e appears. If the Caller ID
message is already stored in memory, you will hear a beep and T h i s d a t a i s
a l r e a d y s t o r e d ! ! appears. The number will not be stored.
2) To complete the setting, follow the steps 3-8 in "Phonebook (Storing Phone
Numbers, Names, Distinctive Rings, and Speed Dial)" on pages 42-43.

Posted on Jan 16, 2008

  • 1 Answer

SOURCE: Uniden CXA15198 not showing caller id

Had a similar issue with a brand new DECT2035 uniden phone, displaying incoming call not caller ID.

Checked my old uniden phone, and it was receiving CID. So I connected my DECT2035 to that line and then lo and behold I got my CID.
After further investigation I found that CID on my dect phone wont work if its using a shared filter (ie. adsl/phone splitter). Had to find an unfiltered splitter and then just put a phone filter (that I got with my adsl modem) onto the line that is directly connecting the phone. and then WOOHOO I have caller ID.

Hope this helps you... I got my wife a little cranky over this one cos it took me over an hour and a half to try and sus this one out =)

Posted on Apr 30, 2009

  • 1 Answer

SOURCE: CALLER ID ONLY SHOWS "INCOMING CALL"

I was using this site while trouble shooting this in the US...
If the customer has DSL with filters in the same system go back to the NID and Isolate the DSL,
test the caller id and call waiting caller id. If this works you have Data Bleed coming from the DSL.
Make sure there are not two sets of filters on the line. Tjis customer had a filter with the DSL modem.

Doing this we just fixed an on going problem for a field tech who was the second callout on a customer issue.

Posted on May 11, 2009

cnavarro
  • 2460 Answers

SOURCE: it does not display the area code on the caller ID

Somewhere, you told it your area code. Take that part out or put a different one in and it will show 10 digits.

Carl

Posted on May 19, 2009

  • 2 Answers

SOURCE: CALLER ID

I just got off the phone with a GE rep, they said to unplug all phones from the wall for 15 minutes, then remove the batteries and put them back in the opposite way they came out. That will reset the system and fix the problem.

If it does not fix it, you'd need to purchase new phones.

Posted on May 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What city or state has area code 333


There is no area code +1 333 in North America (USA, Canada, etc.). It does not exist. Google Voice erroneously assigned some numbers in area code 333, but it is not a real area code. Country code +33 is France, and a number beginning +33 3 is in the northeast part of France. If you see a number on your caller ID that shows up as 333-???-????, it could be: * bogus caller ID data (telemarketer/etc. sending random fake digits)

Mar 02, 2015 | Phones

1 Answer

Call display shows time but not caller number


You also must subscribe, with your local phone company and have caller ID, it is a feature and they do charge a monthly fee for it. If you do have that feature and are still having trouble,

Feb 04, 2014 | NorStar T7316E Corded Phone

1 Answer

The caller Id is only displaying the phone number without the area code and without the name. how can we fix this?


you may have the settings of your ViSYS to so that the phone knows the area code of the phone already.
If so, that will make the caller id display only the 7 digit local phone number. This is so you can easily call back that number, since most telephone exchanges don't require the area code before the phone number if the caller is in your local calling area.

Jun 10, 2010 | RCA ViSYS 2-Line Speakerphone

1 Answer

Phone doesn't show caller id numbers anymore.


You need to make sure you have programmed your area code...check the manual for setting up caller ID. You can search for the manual on line...go to Retrevo.com

http://www.retrevo.com/support/Sony-IT-M602-Telephones-manual/id/751bh629/t/2/

Mar 10, 2010 | Sony IT M602 Corded Phone

1 Answer

When a received call comes in the number shows 1-402 then the number.on call back the phone dials all 11 numbers,then i get a recording from windstream that says i dont need to dial the 1 and area code....


The caller ID in your area is set up to show the 1 plus the area code although not every area has yet to require you to dial the 1 before the number. In the near future it's possible you will have to dial the 1 even if you're calling a local number. I know of no way to change the phone settings in order to remove the 1 in the caller id. Unfortunately it looks like your only option will be to dial the number directly without the 1. Good luck!

Dec 10, 2009 | Panasonic Phones

1 Answer

Area Code not showing on incoming calls. Sakar HT44ID-10


Not all systems require the area code. In fact if I am calling a number in my area from the ID caller & it has the area code shown, I must hit the pound key to erase the area code to make a connection. If it shows only the area code & it is a long distance call, I hit the star key to add a one in front of the existing number.

Aug 21, 2009 | Sakar Caller ID Telephone-White. Price...

1 Answer

It does not display the area code on the caller ID


Somewhere, you told it your area code. Take that part out or put a different one in and it will show 10 digits.

Carl

May 19, 2009 | Uniden Cordless Phone

2 Answers

No Caller ID on display


To set up call id you need to enter programming by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt, press the show key (top right arrow). The display should now ask for an extension number. Enter extension number you wish to program call log on. Press the show key (top right arrow)
Press the next key (bottom right arrow) 5 times. The display should say TELCO FEATURES.
Press the show key (top right arrow) 2 times. The display should say CALLED ID: N(or Y)Press the change key til it says Y.
press the release key.
that should do it providing you have caller id service though your local telco provider.

Mar 25, 2009 | NorStar T7316E Corded Phone

1 Answer

Area code


Here is a link to the site containing a pdf manual link and this is an excerpt for you :

Long Distance calls and Area Code Setting/Cancellation
While the present Caller ID information is displayed, pressing */tone/< will place
or remove the prefix "1" in the display to set the call for a long distance call, or
pressing #/> will set or cancel an area code (see page 30).
Storing Caller ID messages in the Phonebook
Messages shown in the Caller ID list can be stored in the phonebook. The phone
number and name of the party on the Caller ID list can be stored in memory.
1) When the phone is in standby mode, select the Caller ID message to be stored.
Then press the STORE soft key on the base or the EDIT soft key on the handset.
From the handset, then select E D I T ?. S t o r e / E d i t N a m e appears. If the Caller ID
message is already stored in memory, you will hear a beep and T h i s d a t a i s
a l r e a d y s t o r e d ! ! appears. The number will not be stored.
2) To complete the setting, follow the steps 3-8 in "Phonebook (Storing Phone
Numbers, Names, Distinctive Rings, and Speed Dial)" on pages 42-43.

Dec 17, 2007 | Uniden TRU8885-2 Cordless Phone

1 Answer

AREA CODE


Just purchased the GE 25922 today. Looks like you can skip (ignore) the option to enter an area code.

United States' Area Codes are three-digit numbers. If the phone 'requires' entering a number you can use any three digit number. The purpose of this option is to display a local telephone number with only the 7 digits.

Example:
603 - 123 - 4567
'603' is the area code
123-4567 is the 7-digit local number.

If the area code option is programmed to '603', then if that number called '123-4567' would display on the Caller ID display.
Which now reminds me: you would need to also subscribe to Caller ID with the Telephone Company for the numberic display to occur.

Oct 27, 2007 | GE 25922 Cordless Phone

Not finding what you are looking for?
Uniden Cordless Phone Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Uniden Phones Experts

kakima

Level 3 Expert

96738 Answers

Dave Ellis

Level 2 Expert

84 Answers

k24674

Level 3 Expert

7993 Answers

Are you an Uniden Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...