Question about Goodman Heaters

Open Question

Parts schematic or breakdown for goodman GMNT 060-3

I am looking for some kind of parts list or breakdown diagram of the parts for a goodman furnace model GMNT 060-3 ser #0108604061. Can anyone guide me in the right direction.

Thank you

Posted by on

5 Suggested Answers

  • 69 Answers

SOURCE: Furnace start buts shuts off

It sounds like you have an obstruction in the exhaust vent. Thats why when you bybass the pressure switch it runs ok. Steve

Posted on Dec 21, 2008

  • 76 Answers

SOURCE: Need circuit board for Goodman GMNP-060-3 Rev B Furnace

Go to your nearest HVAC supply house. They should be able to get you it.

Posted on Aug 06, 2009

  • 1214 Answers

SOURCE: Model #GMPN100-4 Goodman furnace. Vent fan

The sequence of events for furnace operation is -

Fan purge for 30-45 seconds. During this time, a pressure switch is actuated by the running of the purge fan, proving the control board the purge fan is running.

After purge and purge prove, the hot surface ignition and or spark begins. After a few second delay, the gas valve will open. The control board then monitors for flame prove through another sensor located near the burners. If there is no flame within 3-5 seconds, the gas valve closes. It will repeat this process, usually 3 times, before it shuts the system down, which requires a power down of the system to reset.

I have seen trash get into the hose between the purge blower and the purge switch. But you could be having other problems.

Posted on Dec 17, 2009

  • 15 Answers

SOURCE: Goodman furnace fires up but turns off soon after (over and over)

check grounding and make sure flame sensor is nt dirty .

Posted on Jan 24, 2010

Testimonial: "I cleaned the flame sensor, and that has seemed to do the trick! No problems since then. Thanks!"

  • 66 Answers

SOURCE: Goodman GMNT furnace - should I be able to get

Check the front of the unit and you should see 4 5/16 screws . I believe the outer 2 screws undo the top cover .Remove it first, and remove the inner 2 screws, and the lower door will come off. Good luck. Vern

Posted on Feb 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Goodman dependable 92 light for 6 sec out reignights after 45 sec it does it about 4 times then nothing i turn the pwr on and of thought might be the thermocoupler or flm sensors storm knocked out air


be carefull
only found these

DF]Service Instructions - HVACPartsShop

www.hvacpartsshop.com/manuals/gmph050-3.pdf

Goodman Dependable 92 Furnace Manual - PDF documents

www.do-cu-cu.com/Goodman-Dependable-92-Furnace-Manual.pdf Goodman dependable 92 furnace manual shop for goodman gas furnace repair parts for model gmpn1004 at sears partsdirect. find parts, manuals & diagrams ...

.

Oct 10, 2016 | Goodman Heaters

1 Answer

My Goodman GMNT 120-5 furnace is not coming on.


First I believe you will need to begin by reading this=>

Goodman GMNT120-5 Service Instructions
You will need Adobe Acrobat Reader to view these documents. The Adobe Acrobat Reader is available as a free download.
If you have questions please let me know, Sea Breeze

Nov 03, 2012 | Heaters

1 Answer

I am trying to find manuala for model GMH81155CNAC. Do you where I may be able to locate them?


Google Alpine Home Air. Their website does have a detailed parts breakdown of the GMH furnace. Another option is to go to Goodman manufacturing's website and finding a local dealer who may be willing to get one for you. The dealer search is at the top right hand side of the web site. Good Luck!

Nov 18, 2010 | Goodman GMS90703BXA Heater

1 Answer

Goodman furnace model#GCH90904CXAB the red light


This model is equiped with a diagnostic error control. Take off the front panels and look for a wiring diagram pasted on the reverse side of the panels. On this diagram there will be a chart telling you what 4 blinks represent and where to start looking for the issue. I suspect the air filter may be dirty or the pressure switch may be bad, however make sure the condensate hoses are free of any debris. Good luck to you!

Apr 25, 2010 | Goodman Heaters

1 Answer

Goodman GMNT furnace - should I be able to get remove the access control panel easily?


Check the front of the unit and you should see 4 5/16 screws . I believe the outer 2 screws undo the top cover .Remove it first, and remove the inner 2 screws, and the lower door will come off. Good luck. Vern

Feb 21, 2010 | Goodman GMS90703BXA Heater

1 Answer

My burner goes on but shuts off early and blows cold air. it is a goodman furnace. where should i start to solve this problem. i just had furnace cleaned and flame sensor cleaned. should i buy a new flame...


First when it goes out again, locate the furnace and look thru a small viewing port to see if there is a light blinking, count the number of blinks. Then look at the wiring diagram for a diagnostic code chart. This will give you a strart of where to look.

Oct 17, 2009 | Goodman Heaters

2 Answers

Need circuit board for Goodman GMNP-060-3 Rev B Furnace


Go to your nearest HVAC supply house. They should be able to get you it.

Apr 04, 2009 | Goodman GMS90703BXA Heater

1 Answer

Goodman furnace


you should not need the owners manual. most likely you will find a chart listing the diagnostic codes on the inside of the door to the blower compartment. diagnostics are printed next to the wiring schematic. the most common problem on this style furnace is just a dirty flame sensor. a small piece of fine grit sandpaper and a 1/4" nutdriver is needed. the sensor is located in front of the burner on either the far left or right. be carefull....(do not remove the hot surface ignitor that has two wires). you want the part that has only one wire connected to the sensor under the buner. pull it out and sand the dirt off of the metal rod. reinstall and enjoy your heat

Mar 22, 2009 | Goodman GMS90703BXA Heater

1 Answer

Furnace start buts shuts off


It sounds like you have an obstruction in the exhaust vent. Thats why when you bybass the pressure switch it runs ok. Steve

Dec 15, 2008 | Goodman GMS90703BXA Heater

Not finding what you are looking for?
Heaters Logo

Related Topics:

2,318 people viewed this question

Ask a Question

Usually answered in minutes!

Top Goodman Heaters Experts

paulcarew

Level 3 Expert

1875 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Ken Thomas

Level 2 Expert

118 Answers

Are you a Goodman Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...