Powers up My wii powers up without me pressing the power button, and there is no disc inside

You have to try out all these options first:

Turn the Wii off and on again after about 20 seconds. Press the eject button again.

Unplug the Wii's AC power supply if Step 1 doesn't work. Wait 1 to 2 minutes, and trying to eject the disc again after turning the Wii back on.

Hold down the eject button for 5 to 10 seconds.

Try ejecting the disc with the Wii at different angles. If you hold the Wii upside down, it may help the disc fall out.

Call Nintendo and send the Wii back if non of these steps work. In most cases, a disc stuck in the Wii should be covered by warranty.

Nintendo says to see if power light was coming on, AC adapter reset. unplug from both ends for 90 seconds.Hold eject button for five or 10 seconds.

If none of this works, you might wanna try this, but it is not a preferred method, if you ask me, even though it can be done.

To remove a disc you'll need three sets of tweezers. And possibly a bobby-pin.
First you need to turn the Wii upside down (and preferably unplugged from a power source)
Second, using two sets of tweezers, press the small metal "guards" down. These are located just inside the mouth of the Wii. They're there to keep the disc from free falling, and inhibit their removal. They aren't locked and shouldn't be difficult to press down.
Third, you'll need to reach "up" through the middle of the mouth with the third set of tweezers to grab hold of the disc. I'd highly recommend using flat tweezers, not sharp ones as the disc may become scratched.
NOTE: The disc itself rests on the internal carriage (through the center hole of the disc) and if upside down, should fall into your tweezer's grasp easily. If it doesn't then you need a bobby pin to dislodge. Gently press the bobby pin on top of the disc and then grip the disc with the tweezers.
Finally, gently pull and the disc and push on the bobby pin and the disc will slide out easily .

This can be done with one person, but helps if you have an extra hand.
Good luck.

Synching can be completed only if a compatible game disc is running in the console. Compatible game discs (such as Wii Fit) will display the Wii Balance Board icon on their packaging.
The Wii Balance Board must be synced to each compatible game individually.
These sync settings will be saved even after the console is turned off.

Follow these directions to sync the Wii Balance Board (so that it is recognized by the Wii console):

Insert a Wii Balance Board compatible game disc (such as Wii Fit) in the Wii console.


Use the Wii Remote to select the Disc Channel from the Wii Menu, then select "Start" to begin the game.

Open the SD Card slot cover on the front of the Wii console.

Remove the Battery Cover on the bottom of the Wii Balance Board.

Press and release the SYNC button on the Wii Balance Board. The Power LED on the board will start blinking.

Press and release the SYNC button on the console while the Power LED on the board is still blinking.

The Power LED will stop blinking and light steadily once the synchronization is complete.

Synchronizing the Wii Remote with the Wii Console Synchronizing the Wii Remote to a Wii console allows the Wii Remote to communicate with the console. The Wii Remote included with your system should already be synchronized to your console. However, all additional Wii Remotes you use with your system also need to be synced in order to function properly..
There are two different modes of synchronizing (syncing):

• STANDARD MODE - The Standard Mode procedure is used when adding additional Wii Remotes to your system or if you want to re-synchronize your original Wii Remote. Once synchronized, the Wii Remote will stay synced to the console unless you overwrite the settings by syncing the remote to a different console. For instructions on Standard Mode syncing, please click here.


• ONE TIME MODE - This mode allows you to temporarily use your remote on a Wii console other than your own, or to use a friend's remote on your console. It can also be used to change the order of the Wii Remotes, without the need to turn off the Wii console. One Time Mode does not delete the Standard Mode setting stored in the Wii Remote. In this mode, the Wii Remote will only communicate with the Wii console while the power is on. When the power is turned off, the Wii Remote will lose its sync with the Wii Console. For instructions on One Time Mode setup, please click here.

Note: Only a Wii Remote in Standard Mode can turn the Wii console power ON or OFF.

Standard Mode Synchronization
Note: Make sure you have placed batteries in the Wii Remote (how to).

1. Press the Power button on the Wii console to turn it on.


2. Open the SD Card Slot cover on the front of the Wii console. Remove the battery cover on the back of the Wii Remote you wish to sync up.


3. Press and release the SYNC button just below the batteries on the Wii Remote; the Player LED will blink. Quickly press and release the SYNC button on the inside of the SD Card compartment on the console.


4. When the Player LED blinking stops, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).
This procedure must be followed for each additional Wii Remote added to your system.
Go to the Next Step (Playing Game Discs) >

One Time Mode SynchronizationNote: This mode temporarily removes Standard Mode synchronization setup for all Wii Remotes until the power of the Wii console is turned off. When the power is turned back on again, the Standard Mode settings will return.

1. Press the HOME Button on a Wii Remote that is synchronized with the Wii console.

2. Select the Wii Remote Settings option from the Home Button menu.

3. Select the Reconnect Option.


4. Press the 1 and 2 Buttons at the same time on the Wii Remote that you want to synchronize with the console. If you are syncing multiple Wii Remotes, press the 1 and 2 Buttons on each Wii Remote immediately (without a significant pause) in the order you want them synced. The order in which you synchronize Wii Remotes determines the player order (1 through 4) for multiplayer games. The Player LED will blink during the syncing process. When the blinking stops, the connection is complete.

willysm38

If the unit loses all power after pressing the power button it sound like a problem with the AC adapter or the power circuit inside the Wii.

What I would do is borrow AC adapter from a friend and try it on your system. If it works then you just need to replace your AC adapter. If it does not work then there is something wrong with the mainboard on the Wii. If you had the system less than a year I would contact Wii support about getting an RMA.

Let me know if you have any more problems or questions

Issken
http://www.fixya.com/users/issken

your wii is fake

Turn the Wii off and on again after about 20 seconds. Press the eject button again.

Unplug the Wii's AC power supply if Step 1 doesn't work. Wait 1 to 2 minutes, and trying to eject the disc again after turning the Wii back on.

Hold down the eject button for 5 to 10 seconds

Try ejecting the disc with the Wii at different angles. If you hold the Wii upside down, it may help the disc fall out.

Call Nintendo and send the Wii back if non of these steps work. In most cases, a disc stuck in the Wii should be covered by warranty.

Nintendo says to see if power light was coming on, AC adapter reset. unplug from both ends for 90 seconds.Hold eject button for five or 10 seconds.

1. Unplug Wii from power outlet.
2. Plug in Wii again.
3. Press power button.
4. Press Eject button for at least 10 seconds.
5. If the disc doesn't eject try holding down the power button for 10 seconds and then the eject button again.

Here are the steps that worked for some:
1. Completely power down the console.
2. Power up the console and get to the Wii Menu.
3. Eject any disc currently in the console.
4. Press the eject button again, without any discs in the drive.
5. Insert the disc that you would like to play.

If this doesn't work then contact Wii customer support.

hai. I am one of the user of wii....... i also got many problem like this..... i solved my problem using wii repair guide....click here to help you........

hello micky1965

Try holding down the eject button for at least 10 seconds after turning on the console. If that doesn't work (or you've already tried that). Try the following steps.

1. Unplug Wii from power outlet.
2. Plug in Wii again.
3. Press power button.
4. Press Eject button for at least 10 seconds.
5. If the disc doesn't eject try holding down the power button for 10 seconds and then the eject button again.

If that fails then either return the console to exchange for a new one or contact Nintendo consumer support. Info follows:

Nintendo Consumer Service Contact Information:
Telephone: 1-800-255-3700

Email webform:

| Nintendo - Customer Service | Contact Us! |


I wouldn't attempt to manually remove the disc (by trying to disassemble your Wii) as it may void your warranty. It could simply be a faulty console in which case Nintendo should replace it within 2 weeks (according to posts I've read). It seems to be a somewhat common problem.

If holding down the eject button doesn't work, there's really not much else you can do. Sometimes unplugging and replugging does the trick.

I've had problems with discs not ejecting and some combination of the steps I wrote above solved the problem.

riz.

althought i have a guide for opening inside the wii.?