Question about Projection Televisions

1 Answer

We have been given a new remote control but the volume does not work and when we try to turn over it works for ma minute then stops working altogether

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 124 Answers

Hi, I think you have a something (an object or liquid) inside the buttons that is causing a short on the remote control board. When you turn the remote control over, the object does not touch the remote control board, this is why the remote control works. I would turn the remote control over and just tap on it firmly a few times. if that does not work, then you might use a blow dryer on the remote control Key. Let me know the outcome so that I can further assist you. Thanks, Mike H

Posted on Nov 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The television wont change channels, only power and volume work,


also check remote control if it the rubber contacts are clean. sometimes moisture seeps into remoted. and several times semiconductor rubber contacts loose their properties with friction and pressure.Try to remove batteries of the remote for several minutes and press buttons to discharge any current stred into capacitors. Put the batteries back into remote and try it.Otherwise Try another of the same remote or there may other problems with TV IR sensor. or switching circuit.

Apr 08, 2010 | Hitachi UltraVision CineForm 55VG825 55"...

1 Answer

The tv turns on but turns itself off after a minute


There can be several causes for this, few of which you can do anything about. However, a few things to try.

1) Replace the batteries on your remote control.
2) Try resetting the logic functions on your tv by unplugging it for a minute, then plugging it back in.
3) Try covering up the infra-red receptor on the front of your TV to see if you're getting unwanted signals from the receptor. taping a piece of foil over that area is perfect. If it doesn't stop after doing these two things you'll probably need to take it to a shop.
4) If this does stop it, then look for unexpected signal sources. Have you added a remote control extender? Added a new device to your audio-video system? Changed to a new remote?

Good luck with your problem...I hope you can work it out.

Mar 28, 2010 | JVC HD-52G787 52" Projection Television

1 Answer

Seems like some type of control board problem. Remote will not work on tv, but works other devices. Manual controls are squirelly. Cannot change inputs. Can move to other inputs on menu but when I hit...


Thats a bad button on the front keypad of the tv . The remote does not work because the tv micro sees a button pressed all the time and never listens to the IR reciever . If you pull the front speaker grill off you will find connector ZF just below the keypad or just inside the access panel. If you do remove that panel don't touch anything else.Just follow the wires down from the keypad to connector ZF. Connector ZF is inline with the wires to the front keypad. Unplug it . Then remote will work like normal. Use it like that or have the front keypad buttons replaced.

Oct 21, 2009 | Mitsubishi WS-65809 65" Rear Projection...

1 Answer

Code to programme Sky Remote to operate new TV?


i have the same problem with the codes 0035 0125 0049 everything works except turning the volume up. have you found a solution yet???

Dec 31, 2008 | Projection Televisions

2 Answers

WS-55511 55in volume turns up by itself & can't switch devices


The remote is not the problem. The switch for volume up on the control panel has become leaky. Very common problem for this generation Mitsubishi. If you don't mind not having the control panel working you can disconnect it and the set will work just fine with the remote. To disconnect the control panel pull the speaker grill, it just snaps off, and remove the front access panel. Once that is done you'll see a cable going to the switches just disconnect it.

Nov 23, 2008 | Mitsubishi WS-55511 55" Rear Projection...

1 Answer

Remote control


Try installing a pair of new alkaline batteries into the remote. If the problem persists, I would suspect the remote is defective and return it to the store for a refund. I have used Philips remotes twice before, and had problems with both of them. I switched to a One-for-All universal remote, and it has been trouble-free, so far.











Jul 05, 2008 | Philips 60P8341 60" Rear Projection...

1 Answer

Remote stopped work for my kp-61hs10


Sounds to me like a problem in the tv, not the remote. A short maybe, or a bad connection somewhere.

Dec 22, 2007 | Sony KP-61HS10 61" Rear Projection...

1 Answer

Trouble w/ my Phillips 50P8341 50 IN. HELP!!!


there is most likely a prob. with the keybd. switches all need to be replaced at the same time.

Aug 22, 2007 | Philips 50P8341 50" Rear Projection...

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...