Question about Frigidaire GLEQ2152ES Electric Dryer

1 Answer

Code The machine stopped working and I could only hear a humming noise. I unplugged it and waited 1 min plugged it back up and I got a PF code. I do not know what it means. I turn the power back on and of several times and it is working fine. Do you know what the PF code means? Thank you

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 145 Answers

The PF stand for Power Failure. When you unplugged it, it truely did have a power failure..

Posted on Nov 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

May tag Neptune showing codes


Error codes appear when there are problems with the door, the inflow and drainage of water and the motor.

Do
Your Maytag Neptune washer displays the "do" help code when the washing machine is trying to start a cycle, but the door is open or not locked properly. If this message is displayed, close the door securely and restart the washing cycle.

FL
The "FL" code indicates that the washing machine was unable to lock the door after you closed it. Open and close the door tightly, then restart the washing cycle.

Sd
The "Sd" code indicates that you have added too much detergent to the washing machine and your laundry has too many suds. The machine will stop displaying this code if it has successfully run the suds recovery cycle, which removes the excess suds from the wash load. If the code remains, reduce the amount of detergent in the load. Use less detergent for similar loads of laundry in the future.

PF
The "PF" code indicates that a power failure has occurred. Restart the wash cycle. If the code still appears, check that the washing machine is still plugged in to the electrical outlet.

Nd
The "nd" code indicates that your Maytag Neptune is not draining as it should. Check that the drain hose isn't kinked and that the stand pipe isn't clogged. If you find either of these problems, fix them before restarting the washing cycle.

LO
The "LO" code appears when the washing machine has finished the selected wash cycle, but cannot unlock the door. Verify that the door is closed properly, push the "Off" button, and wait two minutes. The door should unlock and the error code will disappear. If the error code remains, unplug the washing machine, wait two minutes and plug it back into the electrical outlet.

Lr
The "Lr" code indicates that the washing machine's motor is not running as it should. Have your Maytag Neptune washing machine serviced by a certified Maytag repair professional. Maytag Neptune Priority One Service: (888) 462-9824

NF
The "nF" code appears when the washing machine has tried to fill with water and has failed. Verify that the inlet hoses aren't kinked and that the faucets are fully open.

Od
The "od" code appears when you must open the washer door. The Maytag Neptune washer requires that you open the door between cycles.

Other Codes
* If your Maytag Neptune washing machine displays any codes that are not listed above, contact Maytag Neptune Priority One Service for assistance. Maytag Neptune Priority One Service: (888) 462-9824


Hope this helps (remember to rate and comment this answer).

Apr 03, 2011 | Maytag Dryers

1 Answer

My bravo steam dryer is showing an F1 code, and I can't get it to start


this is a control board issue, you may be able to clear the fault using these steps:

1) Unplug or turn the circuit breaker off for 30 seconds.

2) Plug the dryer back in or turn the breaker back on.

3) Press the Pause/Cancel/Stop button twice to clear the "PF" in the display.

4) Start a short cycle to check the operation of the machine by selecting a cycle and pressing and holding the start button until the machine starts.


If it will not clear then you will need to replace the control board, Good Luck Tim

Mar 05, 2011 | Maytag Bravos 7.0 Cu. Ft. Electric Dryer

1 Answer

I got pf on maytag 3000 dryer how do i fix it?


Hi,
"pf" means Power Failure took place during the cycle or the cycle was interrupted, It comes when power connection is loose to the machine, Unplug your device for 5-10 MINS, plug it back then press CANCEL button.

Good Luck and have a nice day.

Jul 04, 2010 | Maytag Neptune MCE8000AY Electric Dryer

1 Answer

I just plugged in the dryer it has a "PF" message and won't do anything, unplugging dosen't change anything....


Pf is power factor. It is showing you there was an interuption of power. Some models you have to wait at least 3 minutes before you can press stop / pause / cancel to clear the PF. If you still keep getting PF go to the main CB panel and turn off the Dryer CB by physically pushing to breaker to the OFF position to reset the breaker then back to on. You will have to wait again before you can clear the PF. If after resetting the breaker you still get the PF in the display you may have to find out what power you actually have at the outlet. 115V or 230V. Other factors come into play also like 3 or 4 prong connections vs the previous connection. They do make a difference and if the power cord was installed incorrectly the PF will never clear until the cord is connected correctly.


Thanks for using FixYa.

Kelly

Mar 07, 2010 | Dryers

1 Answer

The dryer runs for a couple seconds and then give a PF code which I think means power Failure. brand Frigidaire


that is a power failure code. check the main cisuit breaker and the cord to the dryer and make sure the connections are tight.unplug the unit for a few minutes and plug it back in this should clear the pf code out.

Feb 22, 2010 | Frigidaire AEQ6000ES Electric Dryer

1 Answer

Has code PF and will not start Beeps constantly


PF means a power failure has occurred.
Press and hold the cancel button for several seconds to clear the error. Then press start. If the problem still exist you can unplug the unit wait several minutes an plug it back in. If the error still appears the control board maybe at fault.

Nov 12, 2009 | Kenmore Elite HE4 Electric Dryer

1 Answer

Dryer kicks off circuit breaker, pf code is on dryer. now won't let me do anything


pf is for power failure. sounds like You may have a short somewhere. Be careful of electric shock.

Apr 21, 2009 | Dryers

1 Answer

Whirpool duet dryer stopped working PF signal


PF MEEN PAWER FAUILER SOME HOW YOU LAST POWER TRY TO UNPLUG AND PLUG BACK IN AND PUSH CUNCEL . IT WILL RESET THE BORD IF IT DOSEN;T YOU MAY HAVE A BAD BORD AND IS NOT TAKING COMAND

Jan 20, 2009 | Dryers

2 Answers

Cabrio Dryer has a PF code flashing


pf code is power failure. switch breaker off then on. wait 1 minute

Jul 18, 2008 | Whirlpool Dryers

1 Answer

1-1/2 old dryer keeps stopping


could be a bad motor or timer contacts. can you hear a humming sound coming from the motor if you tried starting it again? if there is none, wait for about 5 mins and try starting it again, hear what happens?..

Feb 24, 2008 | GE DBXR463EBWW Electric Dryer

Not finding what you are looking for?
Frigidaire GLEQ2152ES Electric Dryer Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Are you a Frigidaire Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...