Question about Planar PL1910M (Black) 19 in. Flat Panel LCD Monitor

1 Answer

I changed Desktop resolution setting to higher, Monitor went black with "Out of Range" message

I changed the Desktop resolution setting (right-click on desktop, then setting) to higher. Monitor went black with "Out of Range" message and now I can't see anything to change it back.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 488 Answers

Please try this:
To resolve this behavior, either change the refresh rate, or change the video adapter settings.

To change the refresh rate:

1. Restart the computer, and while it is restarting, press F8 until the Startup menu appears. Press 3, and then press ENTER to start the computer in Safe mode.
2. Right-click the desktop, click Properties, and then click Settings.
3. Click Advanced, click Adapter, and then click Adapter Default from the Refresh Rate list.
4. Click OK, click OK again, and then click Yes to restart the computer in Normal mode.

You can set the colors and screen area to your preferences under Display Properties.


To change the video adapter settings:

1. Restart the computer, and while it is restarting, press F8 until the Startup menu appears. Press 3, and then press ENTER to start the computer in Safe mode.
2. Right-click the desktop, click Properties, and then click Settings.
3. Click Advanced, click Adapter, and then click Change.
4. Click Next, and then click Display a list of all the drivers in a specific location, so you can select the driver you want.
5. Click Next, click Show all hardware, and then click Standard display types under Manufacturers.
6. Click Standard Display Adapter (VGA), and then click Next.
7. Click Yes, click Next, click Finish, and then click Yes to restart the computer.
8. After the computer starts, right-click the desktop, click Properties, and then click Settings.
9. Click 256 colors, click Apply, and then restart the computer.
10. After the computer starts, click Start, point to Settings, click Control Panel, and then double-click System.
11. Click Device Manager, click View devices by type, and then click Display adapters.
12. Click Standard Display Adapter (VGA), click Remove, and then click OK.
13. Install all updated monitor drivers.

hope it helps!

Posted on Nov 02, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Monitor's resolution need to be increased, how?


Hi

You don't say which operating system you are using.

The monitor resolves images across a fixed range of resolutions and resfresh rates.

It is the resolution of the graphics card or graphics adapter that can be changed, not that of the monitor.

Right click on empty space on your desktop > properties > settings.

Left click and hold on the slider and slide to the right in stages.

Each resolution change offers you a test page to accept or reject.

When satisfied Apply > Yes > Ok.

To reset the Refresh Rate:

Properties > settings > Advanced > Refresh Rate.

Then restart your computer.

Be careful not to exceed the resolution/refresh rate range of your monitor (1280 x 1024) / 75.0 Hz because if you do, when you restart the computer, the monitor will be unable to resolve the image and you will get a blank screen and/or an Out Of Range error message.

An out of range problem might only be resolved by using a different monitor to reset the resolution back to within the range of the preferred monitor.

Hope this helps

Aug 22, 2011 | Northgate MONNG7NSS 17" Flat Panel LCD...

2 Answers

I gives me the message that it is out of range. What do I do?


hello


it is because the vga you have and monitor you have is not compatible at the first use, you have to press F7 while booting up. or if did not work you have to use another monitor to change your resolution into 800X600 and plug it again into the monitor which is out of range to be able to work.


just leave a comments

thank you

Mar 14, 2011 | Sceptre X5g-Komodo VII 15'' LCD Monitor

2 Answers

I am getting a purple out of range box on my screen that floats from top left to bottom right that I can't get rid of.


It is because your Windows monitor settings are OUT OF RANGE if you can boot into Windows normaly just rite click on the desktop, chose properties, than settings tab (if it's XP), go to advance, than monitor, look for frequency refresh rate, change to 60Hz, than save, than reboot

if you can't boot into Windows, try booting in SAFE MODE by pressing (F8) key at startup than do the above starting at -- rite click on the desktop...

Good luck!

Jan 04, 2011 | MPC Computers MPC F1760I 17" FLAT PANEL...

2 Answers

Out of range message


This is caused by a resolution and/or refresh frequency setting in your computer's display properties that exceeds the values supported by the monitor.
Find out the optimum (native) resolution of your monitor (in case of AMV 17V5 it will be 1280x1024 pixels), and supported refresh frequency (usually 60Hz for LCD monitors), and set your display properties to these values.

Nov 23, 2009 | Amptron AMV 17V5 17" LCD Flat Panel...

1 Answer

StarLogic- Out of range


The computer needs its screen resolution reducing or changing in aspect ratio to suit the StarLogic monitor. Use a previously-working monitor and reduce the resolution on the computer to 1024 x 768 pixels or less (right-click an unused part of the desktop, click Properties and select Settings; slide the resolution slider to the left to adjust). The StarLogic monitor will now work; plug it in - do the resolution adjustment again as above, but increasing the resolution until you are happy. Going this way around, your computer will failsafe back to the previous (lower) resolution if the monitor says Out Of Range again, so you cannot lose the display along the way..

Sep 07, 2009 | Star Logic 17" LCD Monitor

2 Answers

Monitor displaying out of range message


Hello and Welcome to FixYa!

This usually happens when you select a resolution or a refresh rate that is beyond the monitor range. For example if your monitor supports a max. resolution of 1024x768 then if you give it a signal of 1600x1200 it will display out of range.

Solution of this problem is to reduce the resolution or refresh rate frequency.

Changing screen resolution in Windows XP: First right-click on the desktop and then left click on Properties from the menu that appears.

The display properties dialogue box will appear as shown in fig 1.1 below, click on the settings tab at the top right of the box.

xp-screen-resolution-1.gif

The areas worth noting are:

Screen Resolution
This slide bar is what you use to change the resolution, the options you have will depend on your graphics card and monitor, but the standard options are 800x600, 1024x768 and 1152x864.

Normally the default (in XP) is set to 800x600 which means the display will be 800 pixels wide and 600 pixels high.

How to Change the Screen Refresh Rate of Your Monitor loadTOCNode(2, 'summary');
  1. Click Start, click Control Panel, click Appearance and Themes, and then click Display.

    Alternatively, right-click the desktop, and then click Properties.
  2. Click the Settings tab, and then click Advanced.
  3. Click the Monitor tab, and then click the screen refresh rate that you want to use.
NOTE:
  • The default refresh rate setting is 60 Hertz (HZ); however, your monitor may support a higher setting. Check your manufacturer's documentation for information about the settings that your monitor supports.
  • If you use a higher refresh rate, you can reduce the rate that your screen flickers; however, if you specify a refresh rate that is too high for your monitor, your screen may become unusable and your hardware may be damaged.
  • Changes to the refresh rate affect all users that log on to the computer.
Source:
http://www.helpwithpcs.com/tipsandtricks/changing-screen-resolution-win-xp.htm
http://support.microsoft.com/kb/311403

Kindly rate me if i was helpful.
Regards,
Waqar

Aug 25, 2009 | Hansol Computers & Internet

2 Answers

Frequency out of range, it read , please change the display mode to 1440 + 900 with 60Hz.


You need to Set the Desktop Display Settings to match those advised by the monitor... in other words, your desktop's resolution settings aren't supported by that monitor, so right click on desktop, choose settings, and change the resolution (1440 x 900 ) and set the Refresh Rate (60 Hz).

Apr 20, 2009 | Envision 19" Widescreen Flat Panel LCD...

2 Answers

Outof Range error message & black screen


To resolve this behavior, either change the refresh rate which is what is chnaged or the resolution or change the video adapter settings.
 
To change the refresh rate:
  1. Restart the computer, and while it is restarting, press F8 until the Startup menu appears. Press 3, and then press ENTER to start the computer in Safe mode.
  2. Right-click the desktop, click Properties, and then click Settings.
  3. Click Advanced, click Adapter, and then click Adapter Default from the Refresh Rate list.
  4. Click OK, click OK again, and then click Yes to restart the computer in Normal mode.
You can set the colors and screen area to your preferences under Display Properties

If the above problem does not help ypu then change the resolution and select the correct resolution which your CPU and monitor both support....

Try the below solution if you know it or else leave it
To change the video adapter settings:
  1. Restart the computer, and while it is restarting, press F8 until the Startup menu appears. Press 3, and then press ENTER to start the computer in Safe mode.
  2. Right-click the desktop, click Properties, and then click Settings.
  3. Click Advanced, click Adapter, and then click Change.
  4. Click Next, and then click Display a list of all the drivers in a specific location, so you can select the driver you want.
  5. Click Next, click Show all hardware, and then click Standard display types underManufacturers.
  6. Click Standard Display Adapter (VGA), and then click Next.
  7. Click Yes, click Next, click Finish, and then click Yes to restart the computer.
  8. After the computer starts, right-click the desktop, click Properties, and then clickSettings.
  9. Click 256 colors, click Apply, and then restart the computer.
  10. After the computer starts, click Start, point to Settings, click Control Panel, and then double-click System.
  11. Click Device Manager, click View devices by type, and then click Display adapters.
  12. Click Standard Display Adapter (VGA), click Remove, and then click OK.
  13. Install all updated monitor drivers.
If the above solutions is not working for you then contact your nearest Harware person for the solution... All the best.

Mar 18, 2009 | HP L1940 19" LCD Monitor

1 Answer

Signal out of range


1: Signal out of range meas the monitor can't handle the input refresh rate. lcd and Tft monitors usually supports 60 and 75Hz refresh rates.
2: The Resolution you are using to view the desktop is too high, this number is depending on the size of the lcd monitor.
a 15" lcd usually runs with: 1024x768 with 60hz
a 17" lcd usually runs with: 1280x1024 with 60hz some of them supports 75hz.
a 19" lcd usually runs with 1600x1200 or higher.

I recommend reading the user manual if you have it, or checking the information on the manufacturer's website.

3: As a solution turn on your computer and after it passes the bios screen press F8 and select VGA mode.

This will enable 640x480 (standard vga) resolution and 60Hz refresh rate, after windows boots up you can change thease nmbers , and windows automatically asks for turning to 800x600 60Hz.

If you want to change the resolution go to: Right click on your desktop, select properties , select settings tab, and adjust the resolution on the bottom of the window.

Hope this helps, good luck.

Nov 10, 2008 | Kogi L7CH Monitor

9 Answers

Monitor out of range


Most commonly, this problem is caused by an incorrect refresh rate setting. LCD monitors typically DO NOT support refresh rates higher than 60hz - and this is no exception. Try running the game in "safe mode" if it has one. Adjusting the in-game video settings should solve the problem, just look for a screen refresh rate or any video-related setting with a number followed by "hz". Set it to 60, everything should be fine.

It could also be that at some point the game changes resolution (this frequently occurs if there is an in-game movie or cut-scene). In this case the resolution settings for the in-game movie might be at fault, check them if you can.

Sep 23, 2007 | Computers & Internet

Not finding what you are looking for?
Planar PL1910M (Black) 19 in. Flat Panel LCD Monitor Logo

Related Topics:

687 people viewed this question

Ask a Question

Usually answered in minutes!

Top Planar Computers & Internet Experts

Clive Gray

Level 3 Expert

1479 Answers

Joe Goldman
Joe Goldman

Level 2 Expert

330 Answers

William Miller
William Miller

Level 3 Expert

8865 Answers

Are you a Planar Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...