Question about Numark TTX1 Turntable

1 Answer

PROBLEM WITH THE PLATTER FUNCTION

Hello, both ttx turntable when i hold the platter, stop and dosent turn alone i need to give it a slow push, plus on ocations, when i press stop and press again star dosent go ahead, need to push the platter, what can be the problem?
Thanks
Wilfred
will_dj91@HOTMAIL.COM

Posted by on

  • WILL_DJ91 Nov 04, 2008

    Hey all credit here gopes to DJCiscoElnino@aol.com for coming up with this mod/fix.

    ok here goes

    original asisphonics link: http://www.asisphonics.net/ubb/ultimateb...


    Text info:

    Cisco el Nino - "since numark fixed thier overheating problems by adding a vent under the platter, i think that what is happeing is that our DC MOTOR DRIVER IC (Toshiba TA7259P) has gone bad what i am going to do it order this, install it and let you know the deal. there only 5.80 a piece and shipping is like 8 dollars. ill get back to you. I am guessing it is sort of like computers CPU, like its got thermal gel/grease on it and all that fun stuff. It is on the Motor's board heres the image

    (IMG:http://img97.imageshack.us/img97/9139/tt...)

    after i install it too, i am also going to cut vents like this under my platter like the updated versions

    (IMG:http://img97.imageshack.us/img97/8523/tt...)


    also take your time when installing the chip.
    1. its sensitive to static.
    2.buy a low heat soldering iron.
    3.do each solder point at a time, wait a few seconds for the IC to cool off. then approach the next.
    also open your ttx and see what exact IC you need. Mine was a Toshiba TA7259P. Also when you order that, order small tube of thermal paste.

    http://www.audiolabga.com/ for parts ordering"

    Thank DJCiscoElNino@aol.com

    Mad props. This elongates the life of the Numark TT turntable series indefinitely, because they are good turntables, but they had this problem. Well, no longer.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 515 Answers

Yes, this is a common problem with the Numark TTX units.

- OPTiC
Numark Repair Videos
Numark DJ Repair
DJ Equipment Sales
Numark Parts

Posted on Jan 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The platter wobbles


Why are there only 1 a 2 years questions left.... goodbye i leave this channel

Mar 22, 2013 | Numark TTX Turntable

1 Answer

Numark ttx/ttx1 pitch fader wonky


Try spraying the slider with Servisol Video 40.

Mar 15, 2013 | Numark TTX1 Turntable

1 Answer

Turntable does not function


Turntable Belt... Try to picture this, remove the c-clip holding the platter to the center spindle. Remove the platter and turn it bottom side up, place the rubber belt around the platter and fix it to the little post sticking up on the outer-edge surface. The little post holds the belt to the platter while you turn the platter over and put it on so that the post points right over the motor pulley. Turn the platter by hand either clockwise or counter-CW and the belt will pop off of the post and land on the motor pulley. One drop of oil on the center spindle for lube and fasten the e-clip back on.

Nov 01, 2010 | Seth Thomas Pacconi Turntable

2 Answers

Start/stop button doesn't move platter


nakered switch then needs replacing

Aug 07, 2009 | Numark Pro TT-2 Turntable

1 Answer

Numark TTX-1 turntable starts slow but then is okay.


A drop or two of light oil at the center of the spindle will surely solve the problem.Remove the platter and check if its clean

Jul 06, 2009 | Numark TTX Turntable

1 Answer

How do I remove the Numark TTX platter


Nope, nothing to it. The platter is just held down by gravity. Take a mallet or a piece of 2x4 block, and give the spindle a little whack. Not too hard, just enough to break the hold.

- OPTiC
Numark Repair Videos
Numark DJ Repair
DJ Equipment Sales
Numark Parts

Jan 04, 2009 | Numark TTX1 Turntable

1 Answer

Numark ttx turntable


More than likely the drive IC (integrated circuit) has shorted, and needs to be replaced. Not an easy fix, and you'll have to take it to a service center for replacement.

This is a common problem on this turntable.

- OPTiC
Turntable Repair Expert
Digital Analog Therapy

Nov 14, 2008 | Numark TTX1 Turntable

1 Answer

Numark TTX1 Turntable Problem-Platter stops


This is a drive issue. Unfortunately the TTX direct drive system isn't the greatest. It's good, but it's no Technics 1200. The only way to 'fix' this issue is to have a professional look at main circuit board to see if there are any components which are burned, or damaged in any way.

Hope this helps some.

- OPTiC.
Digital Analog Therapy
www.djprolab.com

Nov 04, 2008 | Numark TTX1 Turntable

1 Answer

Ttx 1 numark


hiya fixya...well i just opted,,,to take the thing to the repairs.the conclution is that the"platter rotation sensor " had burned out.sent the deck off today.will let you know the outcome,to maybe pass on this info to other ttx 1 users for near future....thanks for your responce.quote 35 quid just to confirm problem...but deducted from final bill of??????.westend dj staff are very helpful indeed where i puchased them from in the begining.

Mar 31, 2008 | Numark TTX1 Turntable

Not finding what you are looking for?
Numark TTX1 Turntable Logo

Related Topics:

1,170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Numark Turntables Experts

 Grubhead
Grubhead

Level 3 Expert

4590 Answers

Jazz Boyce
Jazz Boyce

Level 1 Expert

728 Answers

Steve

Level 3 Expert

3287 Answers

Are you a Numark Turntable Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...