Question about GE 13TVR70 13 in. Combo

1 Answer

TV will not hold power

I press the power button and it starts to power up, you can hear it and then it immediately turns off?

It was playing fine just yesterday?

Any ideas?

Thank you so much!

Andrea

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Could be the parental control.  See Mark Z solution for power LCD blinks, put TV will not power up. Hold remote power switch down for 6 to 8 seconds to get out of parental control mode. 

Posted on Nov 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reset button on a powerbook g4


The Powerbook G4 power button functions like a reset button if you hold the power button in for a few seconds until the computer powers down.
  1. Hold the power button in for a few seconds (until you see the screen turn off/go black and hear the fans & hard drive stop spinning).
  2. Press the power button again to turn your computer on.
  3. If you have more trouble, you may need to boot in Safe Mode or "perform a Safe Boot":
    Press and hold down the "Shift" key immediately after you hear the start-up tone. Release the "Shift" key when the gray Apple icon appears on the screen.

May 02, 2014 | Apple 15" PowerBook G4 Aluminum 1.67 GHz...

Tip

PS3 Has no Video - Simple fix!


When you attach your Play Station 3 to an HD TV through an HDMI port, the Play Station 3 will ask you if you wish to switch to HD Mode.

However, if you decide to move it to another TV that is not HD compatible, you will get no picture because the Play Station 3 is “stuck” in HD (HDMI) mode.

Follow these steps to resolve your problem:

1. Turn off the PS3 so it only shows a red light. You can hold the power button on the front until it goes into standby. To be sure, flick the power switch on the back of the Play Station 3 off and then back on.

2. Make sure your Play Station 3 is connected to your regular TV (not HDTV) with the standard video cables.

3. Press and hold the power button until the screen "flickers" and then immediately release. This should reset the video settings.

4. Wait a few seconds, and the Play Station 3 (PS3) logo should appear.

If this does not resolve the problem, follow these steps:

1. Turn off the PS3 so it only shows a red light. You can hold the power button on the front until it goes into standby. To be sure, flick the power switch on the back of the Play Station 3 off and then back on.

2. Make sure your Play Station 3 is connected to your regular TV (not HDTV) with the standard video cables.

3. Press and hold the power button on the front until the Play Station 3 beeps and then turns off again. This should reset the video for you and you can turn it back on after this.



That’s it! You can play your Play Station 3 again!

on May 13, 2010 | Video Game Consoles & Games

Tip

How to change or reset PS3 Video Display Mode


When you attach your Play Station 3 to an HD TV through an HDMI port, the Play Station 3 will ask you if you wish to switch to HD Mode.

However, if you decide to move it to another TV that is not HD compatible, you will get no picture because the Play Station 3 is “stuck” in HD (HDMI) mode.

Follow these steps to resolve your problem:

1. Turn off the PS3 so it only shows a red light. You can hold the power button on the front until it goes into standby. To be sure, flick the power switch on the back of the Play Station 3 off and then back on.

2. Make sure your Play Station 3 is connected to your regular TV (not HDTV) with the standard video cables.

3. Press and hold the power button until the screen "flickers" and then immediately release. This should reset the video settings.

4. Wait a few seconds, and the Play Station 3 (PS3) logo should appear.

If this does not resolve the problem, follow these steps:

1. Turn off the PS3 so it only shows a red light. You can hold the power button on the front until it goes into standby. To be sure, flick the power switch on the back of the Play Station 3 off and then back on.

2. Make sure your Play Station 3 is connected to your regular TV (not HDTV) with the standard video cables.

3. Press and hold the power button on the front until the Play Station 3 beeps and then turns off again. This should reset the video for you and you can turn it back on after this.



That’s it! You can play your Play Station 3 again!

on Mar 12, 2010 | Video Game Consoles & Games

1 Answer

Moved playstation to friends tv played fine. Connected back to my tv power lights come on but No sound or picture yet all cables are ok


You need to reset the display, follow these steps :

Step 1. Turn the PS3 off into standby (red light on)

Step 2. Press and hold the power button. It will beep when you first press it then beep again 5 seconds later. Release the power button when you hear this second beep.

Step 3. Wait for the PS3 to start up with normal display settings. If you are using HDMI make sure only the HDMI cable is connected when doing the above steps.

Hope this helps and thank you for using FixYa

Nov 14, 2010 | Sony Playstation 3 (PS3) Console

1 Answer

My playstation won't play a game. Everything else works but it won't play a videogame. It freezes everytime u start it.


Dear, before you get in touch with Sony technical support you may want to try to use the PS3 recovery options. The PS3 stores a copy of firmware drivers on the hard-drive and will reload any corrupt files. To access the recovery menu, do this: Make sure the PS3 is turned off Press and hold the power button on the PS3 it will power on then power off. When it's off press and hold the power button again until you hear two beeps. When you hear the double beeps immediately take your finger off the power button (if your system turns off before you get a double beep just try again and hold the button, it should double beep the 2nd time you try) It will ask for the controller to be connected via the USB cable, Turn on the controller and you will have access to the menu. Be aware that you may lose all of your previously saved data (NOT trophies, they're stored online so don't worry).
Thank you for using Fixya and for rating my solution if you find it helpful. Peter_Rei

Aug 05, 2010 | Sony Playstation 3 (PS3) Console

Tip

Dell Laptops (Has power no display issues) 1. Immediately run PSA. (Make sure...


Dell Laptops (Has power no display issues)

1. Immediately run PSA. (Make sure laptop is connected to AC Adapter. Leave laptop off. Press and hold on the Fn key then press power button once).

2. Just wait for about 3 to 5 minutes then you might will hear beeping sounds (no display with beeping sounds) this means that laptop is working fine but no display. This might cause by either the video card or LCD.

3. After hearing beeps turn off laptop. (Press and hold on the power button for about 3 seconds)

4. Leave laptop off. Press and hold on the D key then press power button once. If full screen colors appears this means LCD is working fine and the problem is the video card. If no display from the LCD no colors were displayed try the test again just to make sure. If still the same no full screen colors then the problem is the LCD.

on Dec 03, 2009 | Computers & Internet

1 Answer

Tv and ps3 plugged in and on. av channel shows an empty screen


Follow these steps to resolve your problem:

1. Turn off the PS3 so it only shows a red light. You can hold the power button on the front until it goes into standby. To be sure, flick the power switch on the back of the Play Station 3 off and then back on.

2. Make sure your Play Station 3 is connected to your regular TV (not HDTV) with the standard video cables.

3. Press and hold the power button until the screen "flickers" and then immediately release. This should reset the video settings.

4. Wait a few seconds, and the Play Station 3 (PS3) logo should appear.

If this does not resolve the problem, follow these steps:

1. Turn off the PS3 so it only shows a red light. You can hold the power button on the front until it goes into standby. To be sure, flick the power switch on the back of the Play Station 3 off and then back on.

2. Make sure your Play Station 3 is connected to your regular TV (not HDTV) with the standard video cables.

3. Press and hold the power button on the front until the Play Station 3 beeps and then turns off again. This should reset the video for you and you can turn it back on after this.

Jun 10, 2010 | Sony Playstation 3 (PS3) Console

1 Answer

Ps3 wont display on the tv!!


Follow these steps to resolve your problem:

1. Turn off the PS3 so it only shows a red light. You can hold the power button on the front until it goes into standby. To be sure, flick the power switch on the back of the Play Station 3 off and then back on.

2. Make sure your Play Station 3 is connected to your regular TV (not HDTV) with the standard video cables.

3. Press and hold the power button until the screen "flickers" and then immediately release. This should reset the video settings.

4. Wait a few seconds, and the Play Station 3 (PS3) logo should appear.

If this does not resolve the problem, follow these steps:

1. Turn off the PS3 so it only shows a red light. You can hold the power button on the front until it goes into standby. To be sure, flick the power switch on the back of the Play Station 3 off and then back on.

2. Make sure your Play Station 3 is connected to your regular TV (not HDTV) with the standard video cables.

3. Press and hold the power button on the front until the Play Station 3 beeps and then turns off again. This should reset the video for you and you can turn it back on after this.

Jun 10, 2010 | Sony PlayStation 3 40GB System

1 Answer

Ps3 broken


When you attach your Play Station 3 to an HD TV through an HDMI port, the Play Station 3 will ask you if you wish to switch to HD Mode.

However, if you decide to move it to another TV that is not HD compatible, you will get no picture because the Play Station 3 is “stuck” in HD (HDMI) mode.

Follow these steps to resolve your problem:

1. Turn off the PS3 so it only shows a red light. You can hold the power button on the front until it goes into standby. To be sure, flick the power switch on the back of the Play Station 3 off and then back on.

2. Make sure your Play Station 3 is connected to your regular TV (not HDTV) with the standard video cables.

3. Press and hold the power button until the screen "flickers" and then immediately release. This should reset the video settings.

4. Wait a few seconds, and the Play Station 3 (PS3) logo should appear.

If this does not resolve the problem, follow these steps:

1. Turn off the PS3 so it only shows a red light. You can hold the power button on the front until it goes into standby. To be sure, flick the power switch on the back of the Play Station 3 off and then back on.

2. Make sure your Play Station 3 is connected to your regular TV (not HDTV) with the standard video cables.

3. Press and hold the power button on the front until the Play Station 3 beeps and then turns off again. This should reset the video for you and you can turn it back on after this.



That’s it! You can play your Play Station 3 again!

Nov 06, 2009 | Sony Playstation 3 (PS3) Console

3 Answers

Epson Stylus Photo 1270. All lights flashing. Whats wrong and how can I fix it?


Hi Guys
I had the same problem with all lights flashing nothing working, happened after a panic power shut down. As with peter after the paper button was released, printer lit up like a christmas tree again. I played around with the button combinations and found that holding down the ink button instead of the flashing paper button cleared the problem. Great tip guys saved me a lot of money. cheers me dears clive.

Mar 02, 2009 | Epson Stylus Photo 1270 InkJet Printer

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Televison & Video Experts

The Knight
The Knight

Level 3 Expert

72230 Answers

matt martin
matt martin

Level 3 Expert

1207 Answers

Cindy Wells

Level 3 Expert

4919 Answers

Are you a GE Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...