Question about Light Switches & Dimmers

2 Answers

Craftsman 1/2 HP Garage Door Opener

During the past couple of weeks my garage door opener does not work. There is no light on the keypay and can not turn the lights on. This has happened in the mornings only. It appears that there is no power to the opener. I checked the breaker and it is fine. An hour or so later, the power is back on all by itself?!??

Any ideas on how the power just goes out and mysteriously comes back on?

Posted by on

  • Frank
    Frank May 11, 2010

    what is the temperture in the morning and what is when it comes back????

    if it is temperture related porblem. you need to check the cable for shorts or open. or the outlet the power is plugged in is not functioning.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If your wall button or Key Pad have nothing on you probably have a bad board. look on back of operator where your wires plug in. There should be a little button 1/2 inch by 1/2 inch button. There will be a little Led Light beside it. Press a remote button and watch it if it lights up you have power to opener. If it does not light your board went out. Replace Key Pad

Posted on Nov 27, 2008

The tempatures in the morning have been cool, about 40F and an hour later slightly warmer, maybe 45-50F. Thanks for the suggestion and I am going to have the cale checked for shorts or opens. The opener is direct wired to the breaker, so no outlet is involved. The morning have been cooler since my original post and have not seen the problem again. Maybe its Grimlins? I'll update if anything wrong is found. Thanks!

Posted on Nov 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to synch remotes on a Liftmaster 1/2 HP Security + garage Door opener


Click the learn button on the receiver followed by the remote. See e.g. http://www.liftmaster.com/CatalogResourcesV3/en-us/shared/files/tucmanuals/114A4109.pdf

Jul 25, 2014 | liftmaster Chamberlain Garage Door Opener...

1 Answer

Hi.. my 1/2 horse liftmaster garage door op[ening is having ANM issue the remote in the truck only opens the door doesnt close it anymore...when you click it.....it ticks repeatedly at the 1/2 unit....my...


Ensure that your electric eyes are aligned.
Disconnect the opener from the door and run the door down & up by hand. Does it move smoothly?
Most openers only require momentary contact to get them to open or close.
I have a doorbell button on mine in my house.

Gary

Aug 25, 2011 | liftmaster Chamberlain Garage Door Opener...

1 Answer

I have a liftmaster formula 1 garage door opener. for the past year, the remote will work every time if in the garage, however, outside of the garage it only works maybe 10 percent of time and then i have...


Yes, replace the remote battery. It is losing power, thus working at short range only. Loss of range is the key indicator for a remote battery going out.

--W/D--

Jan 15, 2011 | liftmaster Chamberlain Garage Door Opener...

1 Answer

Liftmaster 1/2 HP Garage Door opener won't open or close. Has been working fine until I pulled out this morning. The door will move freely if I disengage from opener. Went up ladder to see chain not...


The shaft on these garage door motors are not direct drive systems. You'll have to open up the box to see what the actual problem is. I have had stuff like this happen where a gear just slipped out of place.

http://www.aaadooropeners.com/?gclid=CLH3wt628p8CFVZS2goduwSLYQ

Here is a link for a parts supplier. I don't know your model but it looks like most of the Liftmaster worm screw gears and drive gears are plastic so it's possible that one of them has cracked.

Feb 14, 2010 | liftmaster Chamberlain Garage Door Opener...

1 Answer

Door won't close unless I hold the button all the way down.


make sure the eyes are clean and aligned if the opener thinks something is obstructing its path it will not close

Oct 07, 2009 | liftmaster Chamberlain Garage Door Opener...

1 Answer

GARAGE DOOR OPENER WORKS INTERMITTENLY


& to 10n years on a door opener is good. Did you set the pressure up high there are two dials on the back and they are numbered 1 2 3 to 10 set them to 8 or 9 and see if this solves your problem. What is happening is the sensors are tell your door its hitting something dose the light blink after it stops I need to know more. I would just buy a new one don't get this one fixed not worth it.

Jun 07, 2009 | liftmaster Chamberlain Garage Door Opener...

2 Answers

Wireless keypad for craftsman 1/2 hp garage door opener


Sounds like the new keypad is simply not compatable with your opener. Contact the sears store and speak with the sales person trained on garage door openers. You may find that you simply do not have the wireless key pad you need. good luck

Jan 12, 2009 | Light Switches & Dimmers

1 Answer

Garage door will not work


Check to see if you plugged in the 4 wire limit assy. harness.

Dec 16, 2008 | liftmaster Chamberlain Garage Door Opener...

2 Answers

Garage door not working


increase the opening force by 1/4 turn and decrease the closing force by 1/4 turn on the control box, where the drive shaft for the door is attached, and where the motor is. increase the or decrease the adjustment till the door can be open with minimum of torque.

Dec 01, 2008 | Light Switches & Dimmers

Not finding what you are looking for?
Light Switches & Dimmers Logo

Related Topics:

655 people viewed this question

Ask a Question

Usually answered in minutes!

Top Light Switches & Dimmers Experts

ken skalski

Level 2 Expert

150 Answers

Ottoniel

Level 2 Expert

197 Answers

Hippy_dd

Level 2 Expert

90 Answers

Are you a Light Switch and Dimmer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...