Question about Microsoft Troubleshooting Your Web Page (0-7356-1164-5) for PC

1 Answer

CD-BA1700 mini components system

Hi, When i connect speakers to system and turn on the display shows PROTECT. Is there a way yop get this off ? Is there a battary inside at all ? Please whatever you can help with. Thank you..

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 21 Answers

I am not sure. I could get you in contact with the suppliar for more info. Or I could get in tough with them for you?

Posted on Aug 09, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Protect comes on why


Hello
Protection display will come over this type of set, when it is overloaded or system confused condition. Just unplug the device from AC mains socket and replug it after 4 to 5 minutes, and see whether it shows any protect display. If it shows it again, just disconnect the output loads, ie, connected speakers, and check. Again it displays 'protect', the internal circuit, especially the output amplifier circuits has the trouble, and the system need service. if it does not show protect display, after disconnecting the speakers from it, check the speakers or its connecting wires for damage. OK.

Jan 20, 2012 | Sharp Audio Players & Recorders

1 Answer

My Sharp CD-M10000W displays "PROTECTION"


Generally speaking, an amp attempts to protect itself from heat, shorts, overloads and operator exuberance by refusing to turn on or stay on.

Overloads can be from excessive periods of high output or marginally low impedance loading by the speakers; and shorts would be wiring issues or a speaker blowing up.

You should be able to feel if it's hot. WHY is it overheating? Make sure it has sufficient ventilation on all sides and that vent holes are not blocked by dust balls. Ensure the fan (if equipped) is running as designed (some only operate on demand). Clean dust and debris from it.

If the amp comes back on after cooling, you're lucky. They only have so many self-protection cycles in their lives so continuously resetting or cycling their power without addressing the cause can do more harm than good.

If it protects immediately on a cool power up you should disconnect the speaker connections and try it 'nekkid'. If it comes up then diagnose which lead(s) are shorted. If it does not come up the problem is internal and should be left to an experienced and competent hands-on tech.

Check for loose speaker connections at the speaker as another possible root cause for intermittent shutdown.

Sep 06, 2011 | Sharp Multi-System Mini Component System...

1 Answer

My stereo sysytem is a mini stereo: serial number 10200055. It currently says "protect", what is this and how do we return our system to normal operations?


Hi there,

When the word PROTECT appears on this display, this means the unit has detected a critical fault which could potentially cause harm to your stereo system.

The most common cause is a short circuit somewhere - something even as simple as loose speaker wiring could cause a short, triggering the Protect message.

You will need to determine if there is a possible short somewhere, so I recommend you start by firstly turning power OFF, disconnecting all speaker wires, then turn unit back ON.

Operate the stereo (without speakers) and turn volume up:
  • If Protect message appears when turning volume up, then stereo unit itself has an internal fault
  • If no Protect message appears, then suspect the speakers may be causing the issue.
  • Reduce volume and turn unit OFF
Re-connect speakers (ensure the connections are secure), turn unit ON:
  • If turning volume up triggers the Protect message again, there is an issue with the speakers or connections

Hope this helps.....

Sep 04, 2011 | Kenwood Audio Players & Recorders

1 Answer

I HAVE AN XLMP60 SHARP SYSTEM, ITS IN PROTECT MODE, WHAT CAN I DO?


Hi

If the unit is going into a protect mode, the first thing to do is test the unit with no speakers connected, if it still goes into protect this means that Dc is being detected on the output stage, usually meaning that there is a short circuit on the output stage, therefore the unit needs to be repaired, if it tests find without any speakers connected then either the speaker/s are short circuit or the speaker wiring is short circuit either positive to negitive or positive down to earth, i.e frayed copper wire touching the units casing.

regards

TechSupp12

Dec 11, 2010 | Sharp Multi-System Mini Component System...

1 Answer

My stereo says" protect" everytime i turn it on. can't get anything else.


Hello grammagrisbo, hi your Kenwood head units will show "protect" when there's a problem with the speaker outputs so check to see if the impedance load meets your radio, 8ohms or 4 ohms?. having parallel two speakers on a single channel may cause this dilemma. This might also mean a shorted speaker wire, a blown speaker, or an internal defect in the head unit. Once the condition that's causing the "protect" mode is fixed, the CD player should be back to normal, the next time you turn it on.
If it's staying in "protect", then you'll definitely have to remove the stereo and do something to fix it. Many car audio stores will do system troubleshooting, for a fee. If you want to do it yourself, here's what you need to do:

Pull the Kenwood unit from the dash and disconnect all the speaker wires. power it on and see if the "protect" message displays. If it does, the stereo has an internal defect and will need to be serviced. If it doesn't, then turn it off, and re-connect one speaker only. Turn it on again and see if it will displays "protect" message.

If the radio works with one speaker connected, connect the other speaker to the second channel, you may have now the idea where the problem begun, you will identify the speaker that's causing the problem. There may be a wiring problem or defective speaker in that channel.

If it displays "protect" with a single speaker connected, then disconnect that one and try the other one. If all the speakers cause a "protect" mode, then you're probably back to a defective head unit.

Aug 31, 2010 | Kenwood Car Audio & Video

1 Answer

MY KENWOOD CAR CD PLAYER IS SAYING PROTECT??


Hi,

Kenwood head units show "protect" when there's a problem with the speaker outputs. This might mean a shorted speaker wire, a blown speaker, or an internal defect in the head unit. Once the condition that's causing the "protect" mode is fixed, the CD player should be back in normal mode the next time you turn it on.

If it's staying in "protect", then you'll definitely have to remove the stereo and do some troubleshooting to fix it. Many car audio stores will do system troubleshooting, for a fee. If you want to do it yourself, here's what you need to do:

Pull the Kenwood unit from the dash and disconnect all the speaker wires. Turn it on and see if the "protect" message displays. If it does, the stereo has an internal defect and will need to be serviced. If it doesn't, then turn it off, and re-connect one speaker. Turn it on again and see if it displays "protect".

If it works with a single speaker connected, keep re-connecting the others until you identify the speaker that's causing the problem. There may be a wiring problem or defective speaker in that location.

If it displays "protect" with a single speaker connected, then disconnect that one and try a different one. If all the speakers cause a "protect" mode, then you're probably back to a defective head unit, unless your friend managed to blow all your speakers at once.

Thanks,

Dec 09, 2009 | Kenwood KDC-319 CD Player

1 Answer

Display says protect


check your low voltage fuses, the protect light up when a overload comes....

Jan 28, 2009 | Audio Players & Recorders

1 Answer

SHARP BA1700


Dear steve37,
Please switch off the system from the wall socket. Remove the speaker wires from the rear side of the system. power on the system if it works ,the speakers or the wires are defective.
ramesh22

Jun 08, 2008 | Sharp Audio Players & Recorders

3 Answers

Mini Component


That means the output circuit has a problem and you will need to have the unit serviced.

Mar 08, 2008 | Audio Players & Recorders

1 Answer

System keeps sayin protect


The word PROTECT appears because there is a short. It can be in your speakers, try running it without the speakers plugged, or look if the wires arent shorting. If it stil ldoes that, its cause there is a short in it, from the output section. The system does that to prevent from damaging the electronic components inside.

Nov 17, 2006 | JVC MX-K30 CD Shelf System

Not finding what you are looking for?
Microsoft Troubleshooting Your Web Page (0-7356-1164-5) for PC Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Microsoft Computers & Internet Experts

micky dee

Level 3 Expert

3015 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Alun Cox

Level 3 Expert

2678 Answers

Are you a Microsoft Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...