Question about BenQ FP757V2 (Black, Silver) 17 in. Flat Panel LCD Monitor

1 Answer

The screen is white

When i plug in the monitor it turns white... then i plut it into the comp and it blinks. then back to white. but if i leave just the power conected. it stays white for a couple secs. then turns off. (ring turns gold/yello)

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 472 Answers
Re: the screen is white

This is the internal video card of the monitor.
It has either failed, or the cable that connects it to the LCD panel has come out of either the video card or the panel.

Hope that helps =)

Posted on Apr 09, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My monitor is a View Sonic vg181 I left my monitor on that night, now the power on switch just blinks and I cannot shut it off. When I unplug it and plug it back in, I can see the screen getting a bit...

It sounds like it's in PowerSave mode.

Switch off PC and monitor.

Unplug it from PC.

Leave for a minute.

Plug it back in and switch it on.

Power on monitor.

Read screen in case of error message like 'No VGA' or similar.

Dec 30, 2010 | ViewSonic VG181 (White) 18.1 in. Flat...

2 Answers

Monitor directly enter into power afe mode wen we

turn off the cop and unplug all the cables and open the comp tower and remove all memory chip and turn on the comp by plugging just the power cable and leave the comp on for 2-3 min and the comp will beep and thn turn off the cop and pull the power out and put the memoy chips back in the comp and plug all the cables asnd then turn on the comp anf the issue resolved le me know if any problems at
Memory Installation Guidelines

Sep 18, 2009 | Computer Monitors

1 Answer

SVA Color TFT LCD is white on start up but goes blank.

when i turn the computer on the light on the monitor blinks green but i cant get it to turn on..i have a black screen.

Jan 16, 2009 | Computer Monitors

2 Answers

LCD blank screen, blink white

blank_page Use a reset sequence on the monitor-
1. turn off monitor
2. unplug power
3. plug power back in, holding down the last button on the left, then push the power button to turn back on and off three times, holding on the third try until it comes on- hold for ten seconds and release; the monitor should work again

Jul 28, 2008 | Computer Monitors

2 Answers

Lcd doent come on

Hi, This has happened to me a few times. I found few thing that it can be,

1. The motherboard has a fault so will need replacing
2. Cpu is burnt out or faulty so will need replacing
3.Problem with graphics card

start from bottom, what you can try first is reseting bios by locating the jumper swith keep mains plug out . If you need help with this let me know. Also can try battery take out but doest always work properly. Hope this has helped. Thanks


Mar 19, 2008 | Gateway FPD2275W LCD Monitor

1 Answer

Mymonitor is black and the on button from the monitor is green and is flashing

i havent seen this question asked, and believe me i have searched. i have compaq presario, windows xp media edition 2005, 64 amd processor, model # SR2017CL, with HP 1703 17" monitor. Prob-put computer in hibernate mode other evening, without turning it off. when i woke up, screen had diagonal lines going across it. i rebooted, well manually restarted, since comp would not respond.
Message comes up white with black writing, essentially, prob with active desktop, restore or turn off. i tried to turn off and screen went back to diag. lines. looks like the horizontal hold of a tv screen is asque. tried adjusting monitor to no avail.
tried a few more times, was fine for a few mins then went to same thing. now when i turn monitor on it blinks red, blue, and so on.
just whole screen that color. so i am at the point where i dont
know if its the comp or the monitor. (i am quite a newby)
ty for any help you can give

Jan 30, 2008 | HP Pavilion F1703 17" LCD Monitor

1 Answer

My monitor will only blink a black or white screen.

check the warranty online for your screen.. go the the acer support website and look up warranties, and it will ask for a really long number on the back of your screen, and it will tell how long the warranty is good for and what to do with it.
Mine is doing the same thing. flashes white then black and that is all

Dec 31, 2007 | Acer AL2016WBbd Monitor

2 Answers

Dell P1110

Hi, The part where you see some color bars and blinking green led is what we call MONITOR SELF TEST. A diagnostic pattern consisting of four colors (red, green, blue and white) appears, and the LED flashes slowly. this happens when signal cable from the monitor is disconnected from the tower and leaving the power chord for the monitor plugged in. If the monitor works properly on a different computer. then its a problem with the computer's video card sending out signal. im 85% sure that its a problem with your video card.

Oct 02, 2007 | Dell UltraScan P1110 21" CRT Monitor

Not finding what you are looking for?
BenQ FP757V2 (Black, Silver) 17 in. Flat Panel LCD Monitor Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top BenQ Computer Monitors Experts


Level 3 Expert

2598 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1042 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a BenQ Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides