An expert who has achieved level 2 by getting 100 points
An expert that got 5 achievements.
An expert whose answer got voted for 100 times.
An expert who has answered 200 questions.
Re: BJC55 Printer not printing
There are some possibilities due to the above phenomena. Let's discuss about it: 1) If the POWER light is flashing green, then your printer is now warming up or performing maintenance procedure (replacing cartridge/tank) or cleaning print head, just wait a few seconds till the light stop flash. Also if the last page of a print job not done, this POWER light flashing green. 2) If the CHARGE/ERROR light is flashing orange with beep 3times, it mean your cartridge need to be install (especially the 1st time turn on printer) or cartridge being replaced, just install the cartridge and press RESUME to continue. 3) If both POWER light is flashing green and CHARGE/ERROR light is flashing orange with beep 3times, then your printer may facing a very serious error and maybe need a replacement.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
2 times - No paper (ASF)  * No paper in the cassette 
3 times - Paper jam  * Paper jam in the rear guide  * Paper jam in the under guide  * Front door closed 
4 times - No ink  * Ink tank not installed 
5 times - The print head is not installed  * Print head temperature sensor  * Faulty EEPROM data of the print head 
6 times - Inner cover open  * Inner cover open (while printing)  * Inner cover open (printing continuous) ; (printing not continuous) 
7 times - Multiple ink tanks of the same color installed  * Ink tank in wrong position 
8 times - Warning: The waste ink absorber becomes almost full 
9 times - The digital/video camera does not support Camera Direct Printing 
10 times - Automatic duplex printing cannot be performed (paper size not supported) 
11 times - Failed in automatic print head alignment 
13 times - The remaining ink amount unknown 
14 times - Ink tank not recognized 
15 times - Ink tank not recognized [1410 to 1419] * No Blinking Access cover open 
16 times - Valve sensor [6C00]
ORANGE / GREEN FLASHES
2 times - Carriage  3 times - Line feed  4 times - Purge cam sensor [5C00] 5 times - ASF (cam) sensor  6 times - Internal temperature  7 times - Waste ink absorber full [5B00] 8 times - Print head temperature rise  9 times - EEPROM  11 times - Carriage lift mechanism  12 times - AP position [6A00] 13 times - Paper feed position [6B00] 14 times - Paper feed cam sensor [6B10] 15 times - USB Host VBUS overcurrent  17 times - Motor driver [6D00] 18 times - NIC Board  19 times - Ink tank position sensor  20 times - Other hardware  * Alt. Blinking ROM * Light in Orange RAM
SERVICE MODE This printer has a service mode for service-related settings and for performing test prints. The operator panel buttons are used to enter the desired service mode.
Service Mode Operations 1. With the printer powered off, hold down the Resume/Cancel button and press the Power button. 2. While holding down the Power button, release the Resume/Cancel button and press the Resume/Cancel button twice in succession. Now release the Power and Resume/Cancel buttons. 3. Select one of the following service mode functions by pressing the Resume/Cancel button the specified number of times.
Count Indicator Functions • 0 times Green Print head not installed, carriage returns and locks in home position • 1 time Orange Service test print • 2 times Green EEPROM information print • 3 times Orange EEPROM initialization • 4 times Green Waste ink counter setting • 5 times Orange Destination setting • 6 times Green Print head deep cleaning • 7 times Orange LF correction • 14 times Green Left margin correction
Execute the selected function (except for model setting) by pressing the Power button. The printer will switch itself off after performing the function.
Probably your waste ink counter. Should be cleaned or replaced before
resetting but usually you can get away with resetting once. 1. Start with printer OFF 2. Hold down RESUME and then hold down POWER 3. Release RESUME 4. press RESUME twice, then release POWER 5. let green light blink until printhead has finished moving. 6. Select functions below with RESUME, execute with POWER
0 presses - green light - Test Print (exit service for i960) 1 press - orange light - EEPROM info print 2 presses - green light - EEPROM initialise 3 presses - orange light - reset waste ink counter.
Reload the paper correctly and press the RESUME/CANCEL button.
Three flashes: Paper jam
If paper has jammed in the printer, clear the jam, reload the paper in the printer correctly and press the RESUME/CANCEL button.
See Paper Jams
Four flashes: Empty ink tank
If you press the RESUME/CANCEL button, it will continue printing with an empty ink tank. After printing is finished, replace the ink tank immediately. If you continue printing with an empty ink tank, it may cause damage to your printer.
Refer to your Quick Start Guide for instructions on how to replace an ink tank.
Five flashes: No print head installed/Defective print head
Install the print head. Also, ensure that the protective tape has been removed.
If reinstalling the print head does not solve the problem, replace it with a new one. Contact the Customer Care Center.
Eight flashes: Waste ink tank almost full
The printer has a built-in waste ink tank for the ink used during print head cleaning. Eight flashes indicates that the waste ink tank is nearly full. Press the RESUME/CANCEL button to cancel the error so you can continue printing. Before the waste ink tank becomes completely full, contact the Customer Care Center.
If the CHARGE/ERROR light is remain on orange with beep 1times,
it mean the paper is not properly set in the feed slot, just remove the paper and reload it properly. If the POWER light is flashing green, that mean your print job is not finish yet.
1. Hold down RESUME and then hold down POWER 2. Release RESUME 3. Press RESUME twice, then release POWER 4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute: presses - light color - function
Number of presses - light color - function 0 presses - green - Test print (or exit service mode on i960) 1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i850) 2 presses - green - EEPROM initialize 3 presses - orange - Reset waste ink counter