Question about Haier XQG50-11 Front Load Washer / Dryer

2 Answers

Haier XQG50-11 I have this machine it washes fine but the dryer does not dry. The clothes seem to be wetter at the end of the dry cycle then the wash cycle. The dry cycle does get very hot so the heating element I don't think is a problem. When it is on the dry cycle it almost sounds like it is constantly sending water into it.

Posted by on

  • 1 more comment 
  • camisha_r Nov 17, 2008

    I also have the same problem. Cycle is hot, but clothes (also VERY hot) seem wetter at the end than when they started. This is an intermittant problem, though. Some dry cyles go just fine. But when it doesn't work, it REALLY doesn't work.

  • Roland Bartholomew Apr 23, 2013

    hey i have a haier_xqg50_11 , i srewed up the circuit board by mistake , had it taken out by repairman , and bougt another one to put in but repairman forgot the wiring sequence , can some help me with the wiring sequence?.....i can send pictures of wire colors and circuit board to you , just tell me how to hook it up..

  • Anonymous Mar 27, 2014

    when machine is in drying cycle it only has high heat and no other heat settings

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I had this same problem. There are two possible solutions. First, you need to look underneath (use 2 people) and see if any hoses are kinked. If that is not the case then the machine is pulling in too much water during the dry cycle. I'm hooked up to a sink so I just turn the faucet down until the water is just a trickle. This works for me. If yours is attached to the wall you need to turn down the cold water tap. Its a pain in the ****, but I discovered no one can fix this machine, not even Haier's recommended service A&E. I always know more than the repairmen, very sad. Hope this helped you.

Posted on Nov 21, 2008

  • Roland Bartholomew Apr 23, 2013

    hey i have a haier_xqg50_11 , i srewed up the circuit board by mistake , had it taken out by repairman , and bougt another one to put in but repairman forgot the wiring sequence , can some help me with the wiring sequence?.....i can send pictures of wire colors and circuit board to you , just tell me how to hook it up..

×

Same problems here. It seems steam can not get out. I guess the valve program goes wrong, sending water in instead of sending steam out as it should be.
At least the washer part is fine...

Posted on Nov 10, 2008

  • Roland Bartholomew Apr 23, 2013

    hey i have a haier_xqg50_11 , i screwed up the circuit board by mistake , had it taken out by repairman , and bougt another one to put in but repairman forgot the wiring sequence , can some help me with the wiring sequence?.....i can send pictures of wire colors and circuit board to you , just tell me how to hook it up..

×

1 Suggested Answer

  • 1122 Answers

SOURCE: We have the Haier XQG50-11

make sure your drum is turning,open it quickly and see if it's turning,also make sure you have good ventilation behind the dryer,let me know what you find-mike

Posted on Oct 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dryer not working. Clothes wetter than when they went in?


Could be that the RPM is not enough for the spin as the BELT is loose or slipping or if the motor speed is less due to a worn out CAPACITOR.
Try with a longer drying time or manually dry to confirm .
Also check if the inlet valve is working at any time during this cycle to we the clothes, if so there could be output from the control panel which could be a suspect.

Jul 05, 2012 | Fagor 24" Washer/Dryer Combo with LCD...

1 Answer

Water building up during the dry cycle and clothes getting wetter


1) Make sure wash cycle is 100% finished (sometimes dryer will start before - usu on synthetic cycle & allows water to continue flowing in)

2) Manually start the dry cycle after you ensure wash cycle is finished and push in the wash cycle button.

Hope that helps! If not, you may need a new control module (I did - hope you don't!)

Apr 19, 2010 | Haier XQG65-11SU Front Load Washer / Dryer

1 Answer

Things are not drying on a regular cycle like they use to.


Most likely cause is a partially blocked waste water filter. If the filter is blocked, the water wont drain away as well as it should, so the clothes are wetter at the start of the dry cycle than they should be. Ergo, they end up wetter at the end of the dry cycle. Find and clean your filter, this will probably fix the issue. If it doesn't then you may have a problem with the heating element on the dryer. The fact that you say they are not drying like they used to suggests that they are drying to some extent, heater elements tend to either work or fail, rayther than nnot work well, so if you have some drying, but its not as good as it should be, I would put my money on a blocked filter.

Oct 09, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Haier washer/dryer combo not drying clothes


Check things like the Filter / clear fluff...Make sure outlet hose if any is not kinked and passing air..Hope this helps..

Oct 02, 2009 | Haier 14.3 lb. Washer/Dryer Combo

1 Answer

Hwd1000 washer dryer combo is not moving into the drying cycle


Its time you found out where your filter is to clean out thoroughly

Mar 02, 2009 | Haier HWD1000

1 Answer

Hotpoint Aquarius 1200 Washer Dryer not drying.


Hi, I think the problem you have is with the cold water inlet valve? When your machine dries it uses a small amount of water at high pressure through a restricter fitted in the water inlet valve. These break down letting in to much water which cannot evaporate quick enough for it to pump out causing the washing to become wetter than after the wash/spin cycle. The only way of solving this is to replace th tree way water inlet valve. But make sure that the pump is working ok first and that there is nothing in the sump hose trap which is located underneath the washing machine out the bottom of the tub.
Good luck.................

Dec 28, 2008 | Hotpoint Washing Machines

1 Answer

Dryer Problem


EC4 The temperature of air vent
Within 30 minutes of dry cycle there is 5 minutes in which the temperature is not increasing.

You need to call for repairs. Probably the heating element is faulty.

You can create a custom program without a dry cycle and hang dry your clothing.

Nov 21, 2008 | Haier HWD1000

1 Answer

We have the Haier XQG50-11 Combo VENTLESS Washer / Dryer 120 Volt and the problem we are having is that the clothes are not drying. The dryer itself gets plenty hot but the clothes are wetter at the end...


make sure your drum is turning,open it quickly and see if it's turning,also make sure you have good ventilation behind the dryer,let me know what you find-mike

Oct 15, 2008 | Haier Washing Machines

1 Answer

How do you DRY with the Haier washer/dryer


Have you tried lengthening the dryer cycle or running it at a higher temp? The usual culprit for wet clothes is not running a dryer long enough or hot enough. (I remember some stand-alone dryers (coin-operated with a fixed drying time per coin) that needed two cycles to dry stuff.

Jul 12, 2008 | Haier 14.3 lb. Washer/Dryer Combo

Not finding what you are looking for?
Haier XQG50-11 Front Load Washer / Dryer Logo

547 people viewed this question

Ask a Question

Usually answered in minutes!

Top Haier Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Owen Barnes

Level 3 Expert

835 Answers

Are you a Haier Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...