Question about Symbol ES 3000 (ES3000PWR10WW) 24x10/100 Mbps and 2x1000 Mbps Networking Switch

1 Answer

Not communicating Hi, The ES3000 is not pinging from network even though it is functioning properly. Because of this the remote administration is not possible. Can any one suggest any solutions for this. Regards, LaijuSukhalal

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has written 50 answers of more than 400 characters.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 114 Answers
Re: Not communicating

I would check the IP address/subnet mask/ default gateway information and make sure it is correct for the network is on. Then, I would check to make sure that the IP information is valid for the VLAN for which the management interface is assigned. It may be easiest to reset everything from the console and redo the configuration from scratch. Below are several documents that should help you do that. Device Documentation. Quickstart Guide Admin Guide I would review the sections that pertain to setting the IP address and other management features. I could not find a section on reseting the switch to factory defaults, so you may have to contact their support staff for that. 631.738.6213 or 1.800.653.5350

Posted on Sep 18, 2006

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Why Addresses in the IP Address Pool on a Switch Are Exhausted When the Switch Functions as a DHCP Server and It Has a Few Clients?

If the IP address pool has much more resources than needs of clients, the following two reasons may cause address exhaustion:
1. An attacker keeps changing the CHADDR field and sending DHCP Discover packets to exhaust addresses. If so, contact Huawei engineers to deploy DHCP snooping to protect the IP address pool.
2. The DHCP server ping function is enabled on the DHCP server. This function tries to ping the allocated addresses before responding to DHCP Offer packets. If a client responds to any ping packet, the DHCP server considers that there are address conflicts and addresses are exhausted. To solve this problem, two methods are available:
1. Capture packets on the ports connected to the DHCP server. If a client responds to ping packets, prohibit the client.
2. Disable the DHCP server ping function using the undo dhcp server ping packet command.
3. Such as S5700, S6700

Aug 01, 2016 | Networking Hubs & Switches

1 Answer

Network is: 2x AT-FS713FC/SC (fiber connected with each other) behind the "remote" FS713FC i have one motorola acces point ( motorola ap5131). This AP functions properly. I added a...

You got to check a few things prior to perform any troubleshooting step.
1)whenever you face a disconnection check both end FO converters and try to figure out which one lights are blinking and which are not blinking in both ends at the same time.
2) are both the converter is similar make or not? If not please specify both makes.
3)How many devices are connected on both end after the AP's(approx)? Is there any switch or hub also present within the same network?
4)whenever you face a hang/disconnection position disconnect and reconnect power from one of the FO converters and see what happens then disconnect and reconnect power in the other end and see what you get.
Please revert back with the above detail and I feel I will be able to help you out.Rather you will be able to find out where the issue lies by applying the above steps.
All the best.

Nov 14, 2011 | Allied Telesyn AT-FS713FC ST-10...

1 Answer

How do i reset my password i don´t know the ip and the passwort?

You need to phone your ISP to reset the password. Your username is usually the first part of your email address.
Why do you want to reset the password???

Oct 15, 2010 | Symbol ES3000 (ES300010WW)

2 Answers

What is the loop backup ip and why its being use?

Loopback detection is used to prevent any looping of signals of on two ports it will shut the 2 ports down until line is cleared perventing a collision of packet jam Notifies administrator where a problem is

Aug 26, 2010 | D-Link Networking Hubs & Switches

1 Answer

Managed switches not responding to ping commands.

switch not responding to ping commands. hiow do i find out what the problem is

Mar 13, 2009 | 3Com 3C17210 /RETAIL3COM SS III 4400...

1 Answer

No longer pinging...

check the cables, it's possible that a wire used for the comm. from the server to the switch/router is not making proper contact or is broke...

Jun 24, 2008 | NetGear 24-Port (fsm726s&mr814) Networking...

1 Answer

Ping to my device via network

They are correct a lot of networks will block an echo request or a "ping" because or security and bandwidth issues. Just because your device will not pint doesn't mean its not on the network. I would check with your IT department.

May 12, 2008 | 3M Volition Networking Switch

Not finding what you are looking for?
Symbol ES 3000 (ES3000PWR10WW) 24x10/100 Mbps and 2x1000 Mbps Networking Switch Logo

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Symbol Networking Hubs & Switches Experts


Level 3 Expert

4327 Answers


Level 3 Expert

18259 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Symbol Networking Hub and Switch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides