Question about Dell Inspiron 1100 Notebook

2 Answers

No display I dropped my computer recently, and now the display doesnt work, any ideas on what i should test

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

When using an external monitor, you should press the FN key and the hotkey (F8 for Dell's) to toggle the display between the LCD and the external monitor. The hotkey has a "blue" icon that looks like a display or something similar.

Posted on Nov 15, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 275 Answers

You said the display doesnt work ...
connect an external monitor and than start the laptop and than chk if you are getting a display ... if yes ... contact the technical support of the laptop mfg coz maybe you will need a new display

Posted on Oct 31, 2008

  • Ali Khambati
    Ali Khambati Oct 31, 2008

    or call up 18006249896 thats the dell teck support number

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

GE error E61


E61 means you have the neutral and the L2 wire either reversed or in the wrong position. ENTER TEST MODE SEQUENCE by doing the following . 1.Disconnect thepower for 30 seconds.2.Reconnect the power and within 30 seconds press the sequence of buttons listed below.3.Press the "SIGNAL"button.4.Press the "DELAY START"button.5.Press the "SIGNAL"button.6.Press the "DELAY START"button. Now after you have fixed the reveresed wiring problem you will need to remove the fault code fromt he memory otherwise the machine will not work. To remove the fault code do the following ENTER TEST MODE
SEQUENCE (cont.)
You will notice "t01". To choose the test mode that you want toverify, turn the knob to the desired test mode setting.
Push the start/pause button.To cancel the test mode, press on "power".
You will be able to choose another test mode and again press on "start/pause".
The display error codes test allows the service technician to examine and clear the fault log.
DISPLAY ERROR CODES TEST
(t02)
The display error codes test allows the service technician to examine and clear the fault log.
The control shall display the most recent error in the fault logupon entry into the display error codes test. If there are no errors in the fault log, the no error code "E00"shall be displayed on the 7-segment display.
The control shall clear the displayed error from the fault log if the start key is pressed during the display error codes test. After clearing thedisplayed error from the fault log, the appliance shall display the next most recent error from the fault log.
After clearing all errors from the fault log, the control shall display the no error "E00"code on the 7-segment display.
The control shall log the last 8 error codes in the non-volatile memory stored in a circular list.
The control shall avoid logging multiple instances of the same error code. now unplug the appliance for about 30 seconds and replug and everything should be fine



credit to the original author of this solution rcadieux4444

Jun 30, 2012 | PC Laptops

1 Answer

I have a Toshiba Satellite M45 and the monitor no longer works. there are some lines on the screen (left) and the rest of the screen is black.


Hi,
Can you tell us please, what - recently - happen to the lap? have it been shocked, dropped down ,,, ?

To test, u can plug external monitor in the VGA-port, turn ON the laptop, after a minute, toggle the display once, or twice, or 3 times to change the display path to the external monitor.
Tell us your results
Good Luck

May 13, 2011 | Toshiba Satellite M45-S2652 Notebook

1 Answer

Black screen after startup


drop it on the ground lol

Jul 11, 2010 | PC Laptops

1 Answer

Hi i have a HP NX6110, and i want to watch it on my tv, i got the lead (15 pins) that connect my tv to computer, when i connect them up the HP doesnt work, just says no signel, when i go in to my dispaly...


it may need a keystroke to toggle the display from your pc to your tv. try looing for monitor icon on your function keys then press it together with Fn key to transfer the display.

Mar 29, 2010 | HP Compaq nx6110 Notebook

1 Answer

Acer computer won't work with LCD projector


Have you tried a lower resolution?Update the drivers for the video card.
Good Luck

Oct 17, 2009 | Acer PC Laptops

1 Answer

Gateway 450ROG WiFi Not Working


Sounds like you need to look at that board closer. You wifi is not getting power.

Feb 21, 2009 | Gateway 450ROG Notebook

1 Answer

C793tu Audio Error - Internal Mic doesnt work


Did you check the settings in control panel, under sound and audio devices. You need to go to hardware tab and select the appropriate hardwared from the drop down list. Let me know if its works.

Jan 25, 2009 | Compaq Presario Notebook

1 Answer

My screen doesnt work.


I suggest you to perform these steps.
Test the AC adapter Follow the steps below to determine whether the problem is related to the AC adapter or your notebook system board.
  1. Remove the battery and disconnect all external devices from the computer.
  2. Hold the Power button for several seconds, with all power sources removed. This drains residual power from the system, and may correct many problems.
  3. Connect the AC adapter to a wall outlet and plug the other end into the computer.
  4. Press the Power button to start the notebook PC.
If the notebook does not start or the display is blank then check the power indicator light or power socket LED. I suggest you to connect the notebook to external monitor and check whether its working or not. Then please perform the harddrive self test also.

Jan 09, 2009 | Dell Inspiron 1521 Notebook

1 Answer

Compaq presario 2500


at that xp screen the computer loads all of the drivers and windows components. is is possible that something recently installed was not good or something has become corrupted. reboot the computer and as it is coming up continually tap the f8 key. you will get to the windows advanced options menu. choose the option for last known good configuration. if this doesnt solve your problem you may need to reinstall windows on this computer.

Aug 23, 2008 | Compaq Presario 2100U Notebook

1 Answer

Acer aspire 5050 display faliure


you cant see the damage physically, i think it has internal parts that is damage that is why it won't work. try to check internal display wirings of your lcd.

Mar 12, 2008 | Acer Aspire 5050-3242 Notebook

Not finding what you are looking for?
Dell Inspiron 1100 Notebook Logo

Related Topics:

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dell PC Laptops Experts

Coss

Level 3 Expert

1043 Answers

Donna Sander

Level 2 Expert

193 Answers

Jax Planet
Jax Planet

Level 2 Expert

921 Answers

Are you a Dell PC Laptop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...