Question about Frigidaire ATF6000ES Front Load Washer

1 Answer

Hi there, ive got an frigidaire washer atf6000es frnt load

Pumps out wont spin, motor control board? no error code!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Frigidaire Master
  • 2,651 Answers

Yea board or latch)latch usually shows fault. the board is located left rear of unit, first ck for loose wire connection leading to it.

Posted on Oct 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code e52


Good Afternoon Tracy, thank you for allowing me to assist you!

An error code E52 is associated with a tacho signal failure. The motor contains the tachometer and the motor control board reads the signal from the tachometer. If you have replaced both components, then something is preventing the tub from spinning or there is possibly a wiring issue between the motor and motor control board. This is not a typical DIY job. I would recommend reaching out to an experienced appliance tech just to ensure no step has been missed.

Best of luck!

Feb 01, 2014 | Frigidaire ATF6000ES Front Load Washer

1 Answer

My frigidaire affinity front load washer ATF6000 will agitate but wont spin


Hi burwellkaren - Is the washer making a humming noise? If so, either the drainage hose or pump is clogged and needs cleaning. If not, then the unit may possibly be experiencing an issue with the control board not communication correctly, faulty pump, timer, door lock assembly or something more severe like a damaged tub. I will personally recommend contacting a certified technician to narrow down the precise issue before investing in parts that may or may not be the root cause.

Mar 08, 2013 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Frigidaire front load washer (ATF6000SF1) error E20


E20 is not an exact error code. It's indicating a possible pump out problem. Here is a few possible causes of an E20 error code:

1. Restriction in the drain pump

2. Failed pump

3. Water not pumping out fast enough (crimped drain hose)

4. Too many suds ( too much detergent or wrong kind)

5. Pressure switch (not communicating with control board)

6. Loose wire at pressure switch

7. Loose wire at pump or control board

8. Failed control board

Nov 29, 2012 | Frigidaire ATF6000ES Front Load Washer

2 Answers

Not spin


problem with motor control board

Jul 08, 2012 | Frigidaire ATF6000ES Front Load Washer

1 Answer

E20 message want spin


E20 is not an exact error code. It's indicating a possible pump out problem. Here is a few possible causes of an E20 error code:

1. Restriction in the drain pump

2. Failed pump

3. Water not pumping out fast enough (crimped drain hose)

4. Too many suds ( too much detergent or wrong kind)

5. Pressure switch (not communicating with control board)

6. Loose wire at pressure switch

7. Loose wire at pump or control board

8. Failed control board

Apr 29, 2010 | Frigidaire ATF6000ES Front Load Washer

1 Answer

I'm getting an error signal E20 when there is about 15 minutes left in the cycle. Ive tried clearing the hose, not sure what to do??


The most common cause of an E20 error code would be a clogged or damaged drain pump. Other possible issues would be a loose wire to you pressure switch, loose wire at your control board, loose wire at your drian pump, or failed control board. This is not a specific error but from my experience the most likely cause of this issue would be a bad drain pump. Something is clogging the pump or the motor is bad.

hope this helps _MJ_

Jan 31, 2010 | Frigidaire ATF6000ES Front Load Washer

1 Answer

It wont start washing or spin


MIne had the same code. It is the error code for the motor and control board. The book that tells you how to read the code is under the washer behind the front panel. My washer was 4 1/2 years old and was shot. To repair this was $479 for parts and labor, I replaced with a new Amana front load washer for $496.00. Glad I had AHS home warranty only cost me $60.00 for the service call and they sent me a check for a replacement. I probably would not buy another Frigidaire, because a washer should last more than 4 years. Good Luck.

Jan 04, 2010 | Frigidaire ATF6000ES Front Load Washer

2 Answers

My fridaire front load washer will not spin at high speed


HI. Your unit is equipped with a Motor Speed Control Board. This board regulates the spin speed, with the help of a tachometer, which, is located and mounted on the motor. When this Control board is experiencing issues, the spin will not preform at optimal performance. I recommend to replace this Motor Control Board asap. Once replaced, the unit will spin properly.

Nov 17, 2009 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Washer wont drain


I had a Splendide that would do that. To spin and pump out, it actually ran in reverse! I finally found a loose connection on an electronics board near the motor. Another time the big capacitor had a dent in it and wouldn't work anymore. That keeps the motor from starting.

Apr 20, 2009 | Frigidaire ATF6000ES Front Load Washer

Not finding what you are looking for?
Frigidaire ATF6000ES Front Load Washer Logo

Related Topics:

394 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...