Question about Pioneer Elite PRO-1140HD 50 in. Plasma HDTV

2 Answers

TV & Tuner stays in Standby mode

TV and Tuner stays on standby but doesn't turn on
REd LCD stays on = standby mode
The Green LCD never comes on

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pioneer Master
  • 5,568 Answers

Assuming you have tried changing batteries in your remote and any front panel power switch your set has, the main power supply is probably at fault and without some technical background and a couple of test instruments, you will not be able to do the repair yourself.  What you can do though is; unplug the set, let it stand overnight or at least several hours, remove the back panel and look for a separate board with mostly larger components on it; it will have a ferrite core transformer on it and several larger capacitors which are cylindrical and mounted vertically to the board.
 
Before touching anything inside, especially on that board, allow several hours to be safe since the larger capacitors can hold a painful voltage charge for some hours.  
 
If you see signs of overheating such as discoloration of the board material, it may not be repairable but if you can find a part number on the board, you might be able to buy the power supply and install it yourself.
If there are no signs of heat damage to the board, there may be companies offering to repair it as a subassembly instead of repairing the whole set which could be much more expensive.
If you choose to replace or have it done, the power supply still may not be at fault since most are capable of switching on and off if a downstream problem is causing an overload.
 

Posted on Oct 29, 2008

  • dick_o234
    dick_o234 Jul 09, 2013

    how much would it cost to fix

  • Steve Allison
    Steve Allison Jul 10, 2013

    There is a chance that a replacement board from 'shopjimmy' is a 'pull' from a salvage set and may produce the same results. Unfortunately, if the mfr. hasn't upgraded component quality, the same failure will occur again. It's likely that the problem is caused by a decayed (internally) electrolytic capacitor and unless it failed catastrophically, there may be no external sings of it but can only be found using an RCL meter/bridge that can measure not only the part's value but also internal losses. Such a meter costs ~$200 and may not be in every technician's possession. A standard electrolytic capacitor subjected to certain conditions will fail over time, more costly caps are designed for 'switched mode power supply' service and be more resistant to such failures. When I find one (or more) that have failed because of this, it is replaced with the better part and paralleled with a multi-layered ceramic cap with a value of .1-.47uFd with appropriate voltage rating. This keeps the high frequencies and fast rise times from damaging the electrolytic cap and can protect it from failure.

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,003 Answers

Sounds like a bad mainbord or power supply parts @ www.shopjimmy.com

Posted on Mar 10, 2013

  • dick_o234
    dick_o234 Jul 09, 2013

    how much would it cost to be fixed if it was either of those parts

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 15 month Celcus LCD423D913FHD tv will not turn on. The standby light is lit and will flicker but will not power up the tv. What is the likely problem?


Fault with its main board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ . In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Oct 20, 2014 | Televison & Video

1 Answer

Red light & green light alternate but TV does not come on


My tv acted the same way. Easy answer........buy a capacitor kit!
it was my first try on desoldering and soldering and I have been watching the tube with no problem for months now!

Jul 12, 2014 | LG 37LC7D 37 in. LCD HDTV

1 Answer

I have a 52in ilo flat screen television that just stopped turning on. It stays in standby mode. It use to come on and periotically would stay in standby mode. It is now stuck in standby mode.


Check and replace its main board. Contact any service technician. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" will make surf easy.
http://electronicshelponline.blogspot.com/

Feb 17, 2014 | iLO 3200 32 in. LCD Television

1 Answer

Tv stuck on standby


The internal power supply may have failed.

Nov 04, 2013 | Televison & Video

1 Answer

I bought my son a 19" philips tv model # 19pfl340d/27.in order to turn tv on it must be unplugged for 10-15 minutes.The first one I bought did the same thing and I returned it.this one is exactly the...


The remote control will not operate the TV when the TV is in the OFF mode (No LED lit on front bezel). To change the mode from OFF to STANDBY or ON, press the POWER button on the side of the TV. Once the POWER button is pressed, the LED will change to either red to indicate STANDBY or green to indicate ON, whichever mode the TV was in prior to being turned off with the TV POWER button.

By pressing the POWER button on the side of the TV, the mode will toggle from OFF to either STANDBY or ON. If the POWER button is pressed and then the LED on the bezel is red, the TV is in STANDBY mode and will need to be turned on using the remote control. If the POWER button is pressed and then the LED on the bezel is green, the TV is ON.

Nov 11, 2009 | Philips 19PFL3403D/27 19 in. LCD TV

3 Answers

The Power Light is Red


yeah, should stay red when unit is turned off, indicating there's power but it's doing nothing.

Per user manual:
Solid red - power off (standby mode)
blinking red - power off (now cooling)
blinking green - power on (preparing to light lamp)
solid green - power on

Mar 08, 2009 | Panasonic PT-40LC12 40" Rear Projection...

1 Answer

Standby Indicator flashing SONY KD-32NX100UWhen I turn the TV on the TV goes straight into standby red light, I press the on button on the remote and the TV comes on for about twenty seconds then it...


If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1Theinternal circuits are jammed because of electrostaticcharges accumulating on capacitors, or because of a wrong voltage readby the main chip on your monitor controller board. this started theprotection circuit.

2 The protection circuit detected a wrongvoltage or abroken contact, identified an internal fault and kicked in, starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Payparticular attention at inverter and power board, power board can beinspected looking for bulged or leaking capacitors, then tested with amultimeter. The inverter is more difficult to test , there is need toread voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Nov 19, 2008 | Sony KV-35S42 35" TV

1 Answer

LG LCD 37'' standby problem


if you want i will buy the tv from you

Nov 17, 2008 | LG 37LC7D 37 in. LCD HDTV

Not finding what you are looking for?
Pioneer Elite PRO-1140HD 50 in. Plasma HDTV Logo

519 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Televison & Video Experts

The Knight
The Knight

Level 3 Expert

73073 Answers

Jaime Hernandez

Level 3 Expert

2307 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Are you a Pioneer Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...