Question about Chainsaws

3 Answers

How to replace the Husqvarna chainsaw fuel line.

Show me a diagram of the fuel line on an older model Husqvarna chainsaw.

Posted by on

  • 4 more comments 
  • RBVIP Feb 13, 2009

    Husqvarna 345 leaks fuel when gas cap is opened from fuel line/carb? It is a fairly new saw.

  • chrisp522 Apr 05, 2009

    I'm looking to purchase a husky 61, older model (white plastic top)  fuel line is broken, not sure how to replace looks like there are a couple of fuel line/filter combos to choose from.  Looking for repair instructions.

  • lewisont May 04, 2009

    Husqvarna 353 has a gas line that has sprung a leak. need to replace the whole gas line but I don't know how to get at it as it runs through the body of the saw. Can someone tell me where i can get info on replacing that line?


  • Anonymous May 24, 2009

    how do i replace the gas line on a husqvarna chain saw 36cc

  • Anonymous Mar 22, 2014

    fuel line system

  • Anonymous Mar 27, 2014

    purchased a new gas line with pick up already attached, how to install


3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 1,423 Answers

One fuel hose inside tank has the fuel-filter this goes to the primerbulb and from the primerbulb goes another fuel hose to the carburetor and the surplus from the carburetor goes back into tank again some saws have an special air puls line by a hose from an carter pulsation to the carburetor that will move the float needle by a membraan (its no fuel line)

Posted on Jun 29, 2016

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Need diagram for 235 husgavarna

Posted on Dec 30, 2015

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert whose answer got voted for 20 times.

  • Expert
  • 181 Answers

Let me knoe the model number and i'll see what i have....

Posted on Feb 11, 2009


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Starts but stalls when hot. Chain is not too tight

Larry,Carburetor may be dirty, remove and clean or rebuild. Check the attached links,videos,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Husqvarna Chainsaw 235Troubleshooting Repair Help

How to Troubleshoot Husqvarna Chainsaw Problems eHow

Husqvarna 136 Chainsaw Carburetor Rebuild Fuel Line Repair

Apr 19, 2016 | Husqvarna Chain Saw Models 51, 55

1 Answer

Where to find vent line on 359 husqvarna

Husqvarna chainsaw fuel line check and replace - YouTube

? 3:44
Feb 6, 2012 - Uploaded by mweba1
359. ... Husqvarna chainsaw fuel line check and replace. mweba1. SubscribeSubscribed .... You will want to inspect the tank vent and fuel line.

Husqvarna common air leak - YouTube

? 1:51
Apr 11, 2012 - Uploaded by mweba1
Husqvarna common air leak ... Husqvarna 136 ChainsawCarburetor Rebuild & Fuel Line Repair - Duration: 22:39. by donyboy73 59,377 views.

Husqvarna 359 Professional Chain Saw Review

Dec 14, 2015 | Husqvarna Chainsaws

1 Answer

How to replace fuel pick up,line in Husqvarna 1414 chainsaw?

You need to remove carb and then you can access the hole for the fuel tank. you need to go to a Husqvarna dealer and get the correct line. if too big wont go in if too small will leak replace fuel filter when you do it.

Oct 14, 2014 | Husqvarna Chainsaws

1 Answer

I have a 340 Air Injection Chainsaw. We made sure it has gas/oil and chain saw oil. We get it started but it won't stay on? What are we doing wrong.

If it has an air filter make sure it is clean, also check the gas filter in the gas tank,

sometimes it will get gummed up and will pass very little fuel, it can be pulled out

by making a hook on the end of any wired coat hanger or stiff wire, once you pull,

it out remove the fuel filter , put the fuel line back in, make sure it is submerged

in the fuel, if it keeps running, just replace the fuel filter, the gas tank will have

two lines going to it, normally only one has a filter, also make sure the lines are

intact and don't have any cracks or breaks. make sure your gas to oil ratio is

correct. most chains will have it written on the chainsaw, or check your user's

manual. 40:1 ratio on older models , on newer models 50:1 good luck!

Jul 02, 2011 | Husqvarna Chainsaws

1 Answer

I have a Husqvarna model 444 chain saw. The fuel pick up line disolved in the fuel tank. How do I replace?

order new fuel line and filter from
remove top cover, remove air filter, remove fuel line from carburetor, empty gas tank, pull remains of fuel line out of tank and replace with new.

Aug 25, 2010 | Husqvarna Chain Saw 20" Bar

1 Answer

Replacing 16" craftsman chainsaw fuel line. Problem is one line from tank with two ports on carb and two ports on bulb. There is no diagram to show sequence of connections.

The second carburetor port feeds the primer (bleeder), returns excess fuel to tank.
Filtered line to carb, carb to bleeder, bleeder to tank (probably not visible and no hose in tank).

You can find an exploded parts list wit a little detail here:
The print is deceptive, it appears the filtered line feed the bleeder it does not!

If you have more questions or need additional help please reply below and I will get back to you. Good Luck. HTH
Thank You for using FixYa.

Apr 18, 2010 | Husqvarna Craftsman 36cc, 16 In. Gas Chain...

2 Answers

How to replace fuel line/filter 1994 husqvarna 36 chainsaw?

You can find an IPL with fuel system components, part numbers and some detail here: They are probably spread overr multiple images.
Enter the 3 digit model number (no XPs, Es, just the numbers)
Serial number decode – for use with IPL
06 1500198
06 = year produced – 2006 (single digit before 2000)
15 = week produced - March
00198 = 198th unit Husky produced that week
typical fuel system:
Fuel Line Replacement by
  • The hose in the tank with the filter on the free end connects directly to the carburetor input connection.
  • If the saw is equipped with a primer bulb, the output line from the carburetor connects to the suction side of the primer (once the bulb is collapsed it draws fuel from the tank through the carburetor to refill as it inflates).
  • The pressure side of the primer returns displaced fuel to the tank as it is depressed.
Take lots of notes and a few digital photographs to help with reassembly. HTH

Nov 13, 2009 | Chainsaws

1 Answer

Diagram of fuel line for Craftsman 16" chainsaw

Your saw is a Poulan. Try converting the cc to a model number. A 2.2cc Craftsman is often a Poulan model 2200. go to this link and find something that appears the same under (POULAN-WEED-EATER).
The IPL will help. Pay attention to the year there is a different area for older saws.
For a current saw Craftsman should have something available.

Sep 04, 2009 | Husqvarna Craftsman 36cc, 16 In. Gas Chain...

1 Answer

Husqvarna 65 fuel line

This is manuals. You wlll need to find the IPL that applies to you. The exploded diagrams should help you trace the fue lines.

Aug 06, 2009 | Chainsaws

Not finding what you are looking for?
Chainsaws Logo

Related Topics:

3,751 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chainsaws Experts

Jim Parker
Jim Parker

Level 3 Expert

1040 Answers


Level 3 Expert

479 Answers

Phil Walker
Phil Walker

Level 3 Expert

602 Answers

Are you a Chainsaw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides