Question about Kenwood KDC-MP528 CD Player

1 Answer

Kenwood KDCMP528 Hi! I have a Kenwood KDCMP528 radio in my car and I just had the battery replaced in my car so of course it's asking me for the security code and it was a gift 3 years ago when I first bought my car. The person who bought it for me has no idea what the code is and I'm ready to pull my hair out....I've tried every code I could possibly think of that it would have been set as. Can anyone please help me reset this before I run over this stupid radio???

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 34 Answers

For your kdc-mp528 type 2 below will work whith code KCAR entered from the remote

Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press and hold the "Auto" button and "Track up" (next track button on the right) on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

i hope this works for you.

Posted on Jan 08, 2009

  • djheathen
    djheathen Mar 24, 2012

    the volume is a knob, so there is no holding up or down....

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is EC code in kenwood a.c ?


  1. If your car battery died, your Kenwood stereo will ask you for a code. There are various ways to enter the security code; this depends on the model of your Kenwood stereo.
  2. Look in your manual and see what the security code is for your particular Kenwood stereo. There are common security codes on many Kenwood stereos. Kenwood claims security, but its stereos have many of the same security codes. Here are three common security codes: 1-2-3-4 (a code many Kenwood owners use), 3-0-5-1 (a common security code in Kenwood manuals) and KCAR (works on some Kenwood stereo models). You should have a code within the pages of your manual. Luckily, many Kenwood stereos have the same security codes.
  3. Enter the security code into your Kenwood radio. Method #1: During the code request mode, while holding the DISP key depressed, press and hold the "Volume UP" or "DOWN" key for three seconds until the " ... " display disappears. Enter the security code using your Kenwood remote. Method #2: Press the "Auto" and "Track Up" button on the face of radio at the same time until the four dash lines disappear. Enter the security code using your Kenwood remote. Method #3: Press and hold the "One" then the "Six" preset keys until the display shows the letter "C." Enter the security code using your Kenwood remote.
  4. Tips:
  • If you did not have your manual, try the most common codes for Kenwood stereos. If those codes don't work, you can also buy your Kenwood stereo code online. There are places online that will sell you the security code to your Kenwood stereo.
  • Keep your security code and this information in a safe place.

Here is a link to a more detailed site Good Luck

May 18, 2016 | Kenwood Car Audio Receivers

1 Answer

I have a kenwood car radio /cd my battery recently went and was replaced and the radio is now asking for a 4 digit code which i dont have .I have amanual but nothing is written in the back what can i do ?


You can enter a 4-digit security code which must be used when the unit is removed from the vehicle, or the constant power source is disconnected from the unit. When constant power is restored to the unit, the security code must be entered before the unit becomes operational.
If the code is lost or forgotten I am afraid the unit has to be re-coded by a Kenwood dealer.
Good luck with it.

Mar 26, 2011 | Kenwood KDC-MP342U Car CD Player

1 Answer

Kenwood DNX5140 Security Code


did you ever get a resolution... Having the same problem.

Feb 13, 2010 | Kenwood Car Audio Receivers

2 Answers

Need Unlock Code for Kenwood MP235 car stereo


Look for a really small hole in the face plate. Put a tip of a pen into it. Press it in and then it should turn on. If this doesn't work, take it to a place that installs them, they'll help....Usually for free....

Aug 26, 2009 | Kenwood KDC-MP235 CD Player

1 Answer

I have a kenwood Model # KDC-MP4028 and I just changed the battery in my car and now its asking 4 a code I have had this radio for years and I dont know the code and need instructions on how to restart the...


Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

Jun 25, 2009 | Kenwood KDC-MP4028 CD Player

1 Answer

I disconnected my battery on my truck and when i reconnected it, its asking me for a code, and i didnt even set one. what can i do?


Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

Jun 24, 2009 | Kenwood KDC-MP5032 - Car Audio CD MP3...

1 Answer

Changed battery now radio says enter code when i turn it on


Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

Jun 10, 2009 | Kenwood KDC-MP435U CD Player

3 Answers

KENWOOD RADIO CODES


Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

May 26, 2009 | Kenwood KDC-MP228 CD Player

1 Answer

Need the unlock code for kenwood dpx-mp4070 car radio


Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

May 20, 2009 | Kenwood DPX-MP4070 CD / Cassette Player

1 Answer

Security code for kenwood kdcmp528


for your kdc-mp332 type 2 below will work whith code KCAR entered from the remote

Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press and hold the "Auto" button and "Track up" (next track button on the right) on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

i hope this works for you.

Oct 31, 2008 | Kenwood KDC-MP528 CD Player

Not finding what you are looking for?
Kenwood KDC-MP528 CD Player Logo

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio Receivers Experts

xxxxxx xxx

Level 3 Expert

4706 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Are you a Kenwood Car Audio Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...