Question about Marine Electronics

1 Answer

Need info or a manual

I bought a SI TEX fish pro 111 fish finder on e-bay and no manual to show me how to work it!!

Posted by on

  • ranjanmg Jan 23, 2009

    I need 2L-THE Engine wiring diagram for check power supply

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

I've found SI-TEX's support page: http://www.si-tex.com/html/support.html where they say this:

Printed copies of retired products and the manuals above are available for $15, if mailed within the United States.
E-mail or call us to request a printed version of a manual.

Their number is: (727) 576-5734

Posted on Dec 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a very old Si-tex pro II finder that im trying to get running can any give me a diagrame of how the wiring. the coulors of each wire does what? witch plug/wires runs to the tranducer??? Thanks Sam


Hello, Ticle33 did you ever get he hold of a wiring diagram for the si-tex profish II? I am in the same situation and cannot find one. Hope to hear from you. Thanks /Tom

Aug 07, 2011 | SI-TEX Profish Ii Without Transducer 6"...

1 Answer

I recently bought a boat with this type depth finder on it. It was working fine until I was unable to get off a local beach that people commonly pull up on. The water ran out and the entire bottom was...


Hi, make sure that the bottom of the transducer is parallel to the bottom of the boat. It probably has been knocked upwards while on the beach. If not the transducer will need to be replaced. Hope this helps, regards Phil.

Jun 06, 2011 | SI-TEX Sitex Cvs106lmkii Color Lcd With...

1 Answer

When we are deep water (500 ft or deeper) the fish finder will display 3.5-10 ft. and won't show the fish or shows tons of fish. Are we able to set the depth that we would like to see eg: if we are...


Im not familiar with your particular unit but you should be using a low frequency transducer for water over 500'; something like a 50 kHz transducer or a dual frequency transducer like a 50/200kHz for detail with the high freq. but increased depth range on the lower frequency. As far as setting it to 250 ft, you should be able to use the range feature and adjust the maximum to 250'. typically the factory default is automatic so it will caonstantly adjust the range based on the maximum current depth.

May 22, 2011 | Standard Horizon Standard Ff520 Fish...

1 Answer

Want to know depth range just bought boat with this unit know nothing about it


with the correct transducer you can mark fish at 600 and bottom at 100 feet

Jan 31, 2010 | SI-TEX Sitex Cvs106lmkii Color Lcd With...

1 Answer

I need a manual for Si tex profish II


http://www.si-tex.com/html/support.html

E-mail them at custsvc@si-tex.com with your request and they will e-mail the manual to you.

Jan 03, 2009 | SI-TEX Profish Ii Without Transducer 6"...

1 Answer

Need a op. manual for uniden mc-600 fish finder


There is not a Uniden Marine Electronic with MC-600. Here's are all the manuals for Uniden Marine Electronics =>

http://www.uniden.com/index/manuals_results.cfm?cat=7

If it's the Cobra Fish Finder MC600, here's the operation manual =>

http://www.cobra.com/downloads/manuals/MC600C_MANL_ENG1.pdf

Jan 03, 2009 | Marine Electronics

1 Answer

Turning on my Lowrance LCX 111HD fish locator creates static with my ICOM M502 VHF Marine radio.


Hello LJones0455. From your detailed attempts there are few options. Position the transducers one foward one aft. Connect the negitives of the battiers to the boat still route both positive & negitive wiring to all devices. Check the continunity of your transducers include flexing while ohming. Let me know of the results.

Oct 07, 2008 | Marine Electronics

Not finding what you are looking for?
Marine Electronics Logo

Related Topics:

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Marine Electronics Experts

Steve
Steve

Level 3 Expert

688 Answers

Phil Walker
Phil Walker

Level 3 Expert

602 Answers

The Knight
The Knight

Level 3 Expert

68368 Answers

Are you a Marine Electronics Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...