Question about GE 19TVR62 19 in. TV/VCR Combo

1 Answer

TV won't turn on.

When power button is pressed, the green light flashes five times but the TV won't turn on. There is not a tape in the VCR. Thank you for your assistance.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 119 Answers
Re: TV won't turn on.

Try pressing & holding the power button ON THE REMOTE for 6 to 10 seconds. the unit sould come back on. Info should be at the bottom of page 10 of your owners manual for "front panel block"

Posted on Oct 31, 2006

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

5 Answers

Plustron lcd TV/DVD NEED CODE


Try this solution posted by Ipsita:

thank you to IPsita if this work:

The contain below:

icon_minipost.gifRegion code hack posted by ipsita, January 11 2008:
1) Remove the dvd (if present) from the player
2) Open the tray
3) Press STOP on the remote
4) Press 7 0 on the remote
5) Press MENU on the remote
6) You can see the current region on the top of the screen
7) Press the appropriate region code, e.g. press 5 if the region code needs to be Russia. Press 0 to make the dvd player region free.
8) Press MENU


Aug 23, 2008 | Combination Televisions

2 Answers

Where can I find a book on the different UVerse Remot tv codes for a new tv?


Universal remote code for Panasonic TV/VCR/DVD combo is


Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
Code Search If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.
  1. Manually turn on the device (TV, VCR, etc.) to be controlled.
  2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
  4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
  5. Press and release MUTE to install the code. The indicator light goes off.
Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.

Dec 19, 2010 | Panasonic PV-DM2792 Triple Play 27 in....

1 Answer

Flashing green button

Where are you located? If you don't want this Sharp 35VX-H2000 anymore, I will take it, even if it's broken. Thanks.

Jun 29, 2010 | Sharp 35VX-H2000 35 in. TV/VCR Combo

1 Answer


1. Turn on the device you want to control (vcr, satellite receiver, etc.)

2. Press and hold the button you want to program. While holding the device button, press and hold ON-OFF until the LED on the remote control turns on, then release both buttons.

Note that the AUX button can only be programmed using direct code entry.

3. Point the remote control at the device and press and release PLAY, then wait five seconds or until the LED stops flashing.

At this point the remote control is searching for the correct code to program. If, after five seconds, the device you want to control does not turn off, press and release PLAY again to tell the remote to search the next set of codes.

Continue pressing and releasing PLAY until the device turns off or you have searched through all of the codes. There are 20 total sets of codes. If the device does not turn off after pressing PLAY 20 times, then the remote cannot control that particular device.

If the device you want to control does turn off:

1. Press and release REVERSE, then wait two seconds. Repeat this step until the device turns back on.

2. To finish, press and hold STOP until the LED on the remote control turns off.

Oct 17, 2009 | Panasonic PV-C2023 20 in. TV/VCR Combo

3 Answers

Orion Code for Uverse

1382, 3213, 1383, 3202

try one of those

Mar 12, 2009 | Orion FTDV2004 20 in. TV/VCR/DVD Combo

3 Answers

Sylvania tv model # ssc719c

I had the same problem programming my directv remote to recognize the ssc719c. What finally worked was programming AV1 (not 'TV') with the sylvania DVD code 20821. This allowed me to turn the tv on and off and change tv channels, but wouldn't allow me to mute or change the volume. To fix this, (at least in my case) you have to program your remote to recognize the volume and mute buttons in the AV1 slide setting. I assume other (non directv) remotes similarly disable the volume and mute buttons when the remote is not in satellite or tv mode. Anyway, here are the instructions that activated the volume & mute buttons on my remote: "Depending on how you set up your remote, the VOL and
MUTE may control the volume only on your TV, regardless
of the position of the MODE switch. This remote can be set
up so that the VOL and MUTE keys work only with the
component selected by the MODE switch. To enable this
feature, perform the following steps:
1. Press and hold the MUTE and SELECT keys until the
green light under the DIRECTV position flashes twice,
then release both keys.
2. Using the number keys, enter 9-9-3. (The green light
will flash twice after the 3.)
3. Press and release the VOL+ key. (The green light
flashes 4 times.)
Now the VOL and MUTE keys will work only for the
component selected by the MODE switch position."

To sum up: if you find a code for your remote that will turn your tv on and off, but doesn't seem to do much of anything else, it's probably the right code; your remote is probably set up not to recognize volume or mute inputs in AV1 or AV2. You change that using a remote-specific code that's probably found somewhere on the remote maker's website.

Jan 31, 2008 | Sylvania SSC719C 19 in. TV/VCR/DVD Combo

1 Answer

TVSC1320 13 in. combo from January 2000 VCR Tape is Stuck

i took mine out with 2 butter knifes. 1 pressing on each side of the tape forcing it outward while pressing eject at the same time

Dec 23, 2007 | Zenith TVBR1330 13 in. Combo

1 Answer

RCA T13060GY

You or someone may have press record and the set is in record mode. that way whatever time it's set for it will come on. Or you have to unplug to reset. Leave off for atleast 1hour then plug back in.

Sep 23, 2007 | RCA T13208 13 in. TV/VCR Combo

2 Answers

On/off button flashes green, unit will not turn on manually or with remote


Sep 25, 2006 | RCA T19064 19 in. Combo

Not finding what you are looking for?
GE 19TVR62 19 in. TV/VCR Combo Logo

Related Topics:

243 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Combination Televisions Experts

The Knight
The Knight

Level 3 Expert

66537 Answers


Level 3 Expert

2236 Answers


Level 3 Expert

4327 Answers

Are you a GE Combination Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides