Question about Saris T Rax Basic 2 Bike Hitch Mount Rack

1 Answer

Can i connect it on GMS Aveo? - Saris T Rax Basic 2 Bike Hitch Mount Rack

Posted by on

  • dadada1 Oct 29, 2008

    sorry, chevrolet

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Hitch bike racks should connect to any car with a hitch connection on the rear buttom.
Just remove the regular car hitch (if you have one) and replace it with the bike hitch rack.
Hope that it answer you question.

Posted on Oct 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

It is a speedometer that had it wire clipped. Can you fix the connection?


No the wire has many strands that need to be connected to the right spot

Jul 15, 2011 | Sunlite Cycling

Tip

I has to change my WTB Velociraptor 44/50 tyres last week due to age and wear bu


I soon found out that the 44/50 on the tyre is a two-number system introduced by Wilderness Trial Bikes who make the Velociraptor tyres, and is called the GMS both sizes are in millimeters and refer to the size of the inflated tyre, I don't think that it was a popular sizing system I couldn't find much about it but this is what I found out.
  1. The first number is the width of the inner casing in this case 44mm
  2. The second number is the width of the outside tread 50mm
---------figure 1-----722b4b0.gif

These measurements are taken on a standard rim which is 20 mm wide at the bead-capturing point (inner measurement) , with a tyre inflated to 60psi (4 BAR) and maintained for 24 hours.

The recommended pressure range is from
40-75psi on most WTB tyres. Download the PDF on tyres sizes for all the WTB range.

NOTE: > 14.50 psi = 1 Bar


Common BSD (also in inches) vs Actual Wheel Diameter check out my GMS Tip HERE for more information on this critical Bead Size and Tyre size relationship

622mm (24.5") = 29" - Large MTB
622mm (24.5") = 28" - 700C
590mm (23.3") = 26" - Standard MTB
520mm (20.5") = 24" - Childrens MTB
451mm (17.8") = 20" - BMX

NOTE: The BSD of the tyre is always 15% smaller than the Actual Measured Wheeel Diameter

The WTB tyres also have one rotation for the front tyre the treads usually point in this direction and a rear tyre can be used in both directions depending upon its use either Dry Mud OR Cross Country Downhill

on May 14, 2010 | Cycling

1 Answer

The computer will not read mph


Connect it with the USB cable and if that dosen't work install the software that came with it. If your memory card for the device is removable use an adapter to connect the card to the PC.

Feb 21, 2011 | Blackburn 4.0 Bike Computer

1 Answer

Battery connections


Check the voltage rating of the motor (for example 12 volts). If the voltage rating of the battery is half the voltage rating of the motor, then connect one bike wire to the + post of the first battery, connect the - post of that battery to the + post of the second battery and connect the second bike wire to the - post of the second battery. This is a series connection. Two 6 volt batteries connected in series will provide 12 volts. If the voltage of the motor and the battery is the same there would be another connector so I do not think that is the case for your setup.

Jul 28, 2009 | Electric Bicycle Motor, Bike,electric...

1 Answer

I have a schwinn missle fs and it has new batteries. i put the charger on it to charge and the charger light says it's charged but it's not. What could be the problem?


I've never worked on a Schwinn battery-powered scooter, but I'll weigh in--I'd check that the batteries are properly connected to the scooter. The charger may be connecting to the batteries, which are charged, but if the batteries aren't connecting to the motor, you're not going to go anywhere.

The only other thing I can think of to check is for blown fuses. Good luck.

Jun 18, 2009 | Electric Bicycle Motor, Bike,electric...

1 Answer

I would like to know how to wire a bottle dynamo to bike lights


The bottle dynamo rides against the tire turning it . The wires from it go to the front liht. The same two wires  may also be hoked to a back light. The  direction of flow is not that important but most put the same (one of the two ) wire on the center connection. If you generator has only one wire, then the light(s) will have to be grounded through the frame.

Jan 09, 2009 | Classic Accessories Classic Bicycle Dynamo...

Not finding what you are looking for?
Saris T Rax Basic 2 Bike Hitch Mount Rack  Logo

Related Topics:

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saris Cycling Experts

yadayada
yadayada

Level 3 Expert

63456 Answers

kakima

Level 3 Expert

98758 Answers

John Egan
John Egan

Level 2 Expert

72 Answers

Are you a Saris Cycling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...