Question about Computer Speakers

1 Answer

Front left speaker is louder than the right one Replaced my altec lansing speakers because left speaker was louder than right. They were about 6 years old, replaced with Logitech 2300. Same problem. If I turn down the left and turn up the right it seems alot better. But I still don't think it's right. Is it the sound card?

Posted by on

  • Anonymous Jan 02, 2009

    Well balancing is all fine and sweet for me, but my old set of Logitech speakers have the same problem. It the speakers themselves witch are messed. The volume knob is faulty. If I press on it (not turning it! is not meant to be pressed but it does fix it) the balance at low volumes corrects itself.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 34 Answers

JUST ADJUST THE BALANCE IN THE VOLUME CONTROL, YOU CAN FIND IT IN THE CONTROL PANEL OR AN ICON AT THE BOTTOM RIGHT OF YOUR SCREEN, THE RIGHT NEXT TO THE CLOCK.. PLEASE VOTE FOR MY POST

Posted on Oct 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to open left speaker


If you remove the front fabric cover by levering it off using a flat head screw driver, it will reveal the screws to open the speaker up. This is the same for both the left and right speakers.2_6_2016_3_29_16_pm.jpg2_6_2016_3_29_17_pm.jpg

Jul 26, 2013 | Altec Lansing VS2621 Speakers

1 Answer

Need help with altec lansing ada 745 4.1 speakers


Does the right front speaker need to work in order for the whole speaker system to work?

The whole system can still work with or without it.

Here is an additional tip how to ..... Computer Speakers

Sep 29, 2012 | Altec Lansing ADA745 4 Speakers

2 Answers

9 pin diagram altec lansing


can anyone help me with the Altec Lansing VS4121 2.1 Channel i need the wiring diagram of 9 pin cable i broke it. please mail me the layout at maurya.mohit07@gmail.com

May 20, 2012 | Altec Lansing VS4121 2.1 Channel Powered...

1 Answer

I hav altec lansing vs2621, some times sub woofer not working. left and right speakers ok.


Hello
Check its speaker. In subwoofers, the lead wire that goes to the voice coil; goes from the speaker solder terminal to the vocie coil will get internal break and this type of fault sill occur. Intermittent working of speaker will be the result. Lead wire can be replaced. It can be bought from the electronic spare part shops. It is a type of copper braid wire. If you have the skill, fid out which wire is faulty and replace the same. you have to take out the speaker out of the box for repair. Broken wire can be detected by measuring its resistance with a multimeter. OK.

Jun 20, 2011 | Altec Lansing VS2621 Speakers

1 Answer

Ah i have altec lansing acs 45.1.the problem is i dont know how to wiring.can u pls help me.ynx


ok first plug run a1/8 two sided head phone jack[male] from the computer to sub woofer you should have two imput jacks makes no differance ok the left sat speaker has a 6 pin din plug round looking plug insert into subwoofer and then plugac cord in the wall you should be good togo "note right sat speaker is attached to the left good luck

Nov 16, 2010 | Altec Lansing ACS 45.1 Computer Speakers

2 Answers

Altec Lansing ada885


Same issue showed up for me today very randomly...

HD comes on and off for no reason and sound cuts in and out. This fix worked for me:

1.Disconnect the left speaker from the sub woofer.
2.Take the 4 screws out on the bottom of the left speaker. (They are under the rubber matting you can just poke holes through it)
3. Remove the bottom plastic assembly from the speaker
4. Cut the 4 wires to the headset chip. Careful not to cut any others to the speakers themselves!
5. Unscrew and remove headset plug chip
6. Reassemble and plug left speaker back into sub woofer.

No more HD issues =)

Apr 04, 2008 | Altec Lansing ADA 885 Computer Speakers

3 Answers

Need wiring and 9pin connector diagram


Dell (Altec Lansing) A425 Subwoofer Pinouts

This is a standard female DB-9 serial port.
Here are the pinouts.

Pin 1 = Left Speaker Out +

Pin 2 = Left Speaker Out - (Common Ground)

Pin 3 = Left Line In +

Pin 4 = Right Line In +

Pin 5 = Left/Right line In - (Common Ground)

Pin 6 = Right Speaker Out +

Pin 7 = Right Speaker Out - (Common Ground)

Pin 8 = Power A

Pin 9 = Power B

Jumper (short) Power A to B to turn on.
If you want a volume control you need to put one on the inputs. You will buy buy a stereo volume control or potentiometer.
Here is some info on how to do this.
http://g4tv.com/screensavers/features/43665/Pump-Up-The-Volume.html

Cheers!

Mar 27, 2008 | Altec Lansing ADA425 3-piece 30-watt...

2 Answers

How to repair atp3 altec lansing


Best bet would be to just strip the wire with a wire stripper or utility knife and twist the bare ends together to fix the connection. A little electrical tape around those wires and you should be almost good as new. Of course you might notice some difference in quality but I'm pretty sure the only way round that would be replacing the cable.

Try it out and let me know how it works out for you. If you know how to solder it might be a good idea to solder the connection as well.

Jan 04, 2008 | Altec Lansing ATP 3W Computer Speakers

Not finding what you are looking for?
Computer Speakers Logo

Related Topics:

2,007 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computer Speakers Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Carlos L. Burgos
Carlos L. Burgos

Level 2 Expert

508 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Are you a Computer Speaker Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...