Question about Norcent Technologies PM-4203 42 in. EDTV-Ready Plasma Television

Open Question

Norcent 42 inch PM 4203

No picture. For awhile it worked when you tapped it on the lower left hand corner...has been getting progressively worse, sometimes you can't get picture at all, just black screen. It seems like something's just a tad loose or poor connection somewhere.

Posted by on

5 Suggested Answers

  • 140 Answers

SOURCE: norcent television locked

Try this: ?POWER (OFF) > MENU > V-CHIP > MUTE? to revert to the default password of 1111.

Posted on Sep 10, 2007

Testimonial: "great"

SOURCE: no video

I had the same problem too. It called the Y-main Board. It cost $145 if you order directly from Norcent itself. I hope that help.

Posted on Feb 06, 2008

  • 4 Answers

SOURCE: norcent lcd tv 27 inch has sound turns on and off, black screen

wiggle the power cord where it plugs into the set!

Posted on Aug 29, 2009

  • 2 Answers

SOURCE: norcent 42 inch plasma

check the yellow cable

Posted on Apr 10, 2010

  • 11361 Answers

SOURCE: TV is black as if turned off.

You may have lost the 24vdc due to bad caps, this 24vdc is used to power the backlight inverter baord, or you may have failed inverter board. Look for 24vdc first.

You can try looking for parts here: www.shopjimmy.con

Posted on Jun 13, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to factory reset the hp pro 300 laserjet printer

1. Power down the printer
2. Press and hold the lower left hand corner of the screen
a. This is normally where the progress bar starts loading on the screen
3. Power on the printer
4. Release the left hand corner once the "Permanent Storage Init" message appears.

or alterative way
1. Power down the printer
2. Press and hold the right arrow button on the navigational bar
a. This button will flash for a moment when the printer boots up
3. Power on the printer
4. Release the left hand corner once the "Permanent Storage Init" message appears.

Jul 14, 2016 | HP Office Equipment & Supplies

1 Answer

SPN 4235: Picture goes off

It is a loose connection, need to open the unit and the tap on the board and cables connected to check the loose connection. be careful to use a rubber gloves.

Jul 15, 2008 | Samsung SPN4235 42 in. Plasma HDTV

1 Answer

Where are my photos in instagram?

Tap the icon in the lower right hand corner that should have a picture of a person from the shoulders up, or a card with that picture inside it. Either way, lower right hand corner from the main screen.

May 20, 2015 | Apple iPhone 5c

1 Answer

Norcent Technologies PM-4201 42 in. EDTV-Ready Plasma Television that turns itself off within one second. Then the remotes don't work and I have to unplug the tv. Is the tv shot?

Sounds like the main power regulator board inside the TV is faulty. Contact any service technician. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.

Dec 31, 2014 | Norcent Technologies PM-4201 42 in....

1 Answer

Has sounds but no picture

take the back off it and check for burnt capacitors :) and replace the ones which have black leakage on the tops of them or are bulging at the tops.capacitors are what keep the picture lit up :) they hold a charge like batteries

Apr 17, 2012 | Norcent Technologies PM-4203 42 in....

1 Answer

Hello. there is some green lines appearing on my 42 inch norcent plasma monitor display. what could it be? usually it starts after one hour of the tv being on. and if I leave it on for more thatn an hours...

Dear Sir,

Welcome to Fixya.

The problem is related to plasma it is very difficult to fix the problem,so solution is you have to replace your tv plasma screen.But it is too much expensive.Depending on your Plasma EDTV model and size estimation can be done.If it is in warranty you can get free replacement.Visit nearest Norcent Service Centre for more detail.If you have any problem regarding this issue leave a comment we were happy to assist you.

Have a Nice Day.

Oct 08, 2009 | Norcent Technologies PM-4203 42 in....

1 Answer

SPN 4235: Picture goes off


Jul 15, 2008 | Samsung SPN4235 42 in. Plasma HDTV

Not finding what you are looking for?
Norcent Technologies PM-4203 42 in. EDTV-Ready Plasma Television Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Norcent Technologies Televison & Video Experts

The Knight
The Knight

Level 3 Expert

71754 Answers

Jaime Hernandez

Level 3 Expert

2294 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Are you a Norcent Technologies Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides