Question about E-Machines eMachines Monitor E15T4

1 Answer

Screen on moniter is not full

I am now posting this on an emachines W3503 computer that only shows the page in the middle of the screen on my moniter,the sides are black and i can only view the page in the middle of the screen.I tried adjusting the page on the menu of the moniter but its only about 80 percent.How do I get the full screen back on my moniter............thanks.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,601 Answers
Re: Screen on moniter is not full

I think that you need to reinstall or find a new driver for it.


Posted on Oct 23, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

LG Flatron E2042. Brand new. New CPU. Windows 7. I plugged in my new monitor today. Does not turn on automatically. But when I do turn it on I get an error message. D SUB POWER SAVING MODE and tur

Your new moniter may not be compatible with your computer. I have an Emachines that won't take a flat screen. I have to use a big bulky moniter because it says not connected even thought the hookup fits the back of the tower. That might be your problem. Did your old moniter work correctly?

Nov 15, 2012 | Computer Monitors

1 Answer

The moniter blacked out, blue light is saying the moniter is still on, but screen looks like there is no power. When you turn on the moniter, the screen shows up for a few seconds, then blacks out again!...

Unplug power. Unplug VGA cable. Remove back of monitor. (four small Philips headed screws along the bottom rear. Remove screws attaching Monitor to it's base. Carefully, lean the screen away from back of case. Gently unplug 25 pin cable from the screen.
Connect AC power.
Screen should power on Gray to White. Ble light comes on Blue.Flickers then changes to Amber.
Reconnect VGA cable. Monitor should work.
Close up the monitor in reverse order to opening it.
If these steps don't solve your monitor, consider replacing as cost of repairs may shock you.

Sep 09, 2010 | Proview PL926WBi 19" LCD Monitor

1 Answer

Screen black

Take the post (power on self test) disconnect vga cable and connect power cable if monitor shows no signal check signal cable massage then monitor is ok fault is in cpu. open it and clean the dust
by vaccum cleaner you will get the display again

Oct 17, 2008 | X2Gen MG19MY 19" LCD Monitor

1 Answer

15.6 lcd wide moniter (low light)

It's LCD pannel problem

Remove the LCD pannel and checket flowrocent tubes at top of LCD Screen and Bottom of LCD Pannel. If U Find any burning area at end of F tube, please clean it and solder the flowercent tubes in same possion and connect as same.

Oct 03, 2008 | Acer AL2216WBD LCD Monitor

2 Answers

Problem with data cord

Change the data cord if not repaired then change the monitor ,give another companies monitor

Aug 26, 2008 | Philips 105S51 15" CRT Monitor

1 Answer

Osd off

I sugust un hooking the cable from the moniter to the computer, asumuming it is a desktop and then see if it will turn of. If it turns of the you probably have a computer issue. Good luck.


May 14, 2008 | E-Machines eMachines Monitor E15T4

2 Answers

Monitor blinks no image

first you need to isolate the problem to either the computer or the moniter. I would sugust that you hook a know good moniter to the compter and go from there. If the other moniter works then you have a moniter issue aif not chek the video card in the computer. good luck

May 01, 2008 | E-Machines eMachines Monitor E15T4

2 Answers

Blue tinted monitor screen

black and white tracking can vary in color depending on which color that the dispay is not getting enough of or to much of. In the case of it changing when you walk
in to the room, sugust that there is probably a loose connection or poor solder joint on the curicut board of the moniter. I don't suggust that you get inside the moniter and try to fix this due to dagerous voltage potential with in the moniter. Good luck

Apr 18, 2008 | E-Machines eMachines Monitor E15T4

Not finding what you are looking for?
E-Machines eMachines Monitor E15T4 Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top E-Machines Computer Monitors Experts

buzz flewhart
buzz flewhart

Level 3 Expert

655 Answers

Ricky Ostrom
Ricky Ostrom

Level 2 Expert

270 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you an E-Machines Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides