Question about HP LaserJet 3050 All-In-One Printer

1 Answer

How to reset Language

HP 3050 has language set on Dutch; how do I change it back to English or reconfigure it the way it came?

Posted by on

  • deannabaumga Oct 29, 2008

    Have found that 3050 prints and faxes in English; only the display is in Dutch; any ideas on how to change the display or should I learn Dutch?

  • Anonymous Dec 20, 2008

    I have same problem. grandaughter played with the settings. Got it in Russian and I can change the reader back to English. I tried the * and five key hold down but not having much luck.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 87 Answers

When a super NVRAM init is performed, the all-in-one language and telecom country/region settings
are undefined. The user is prompted to set the language and telecom country/region. Until these settings
are defined, the all-in-one will not return to the Ready state.
CAUTION A Super NVRAM init erases all data that is stored in both the unprotected and
protected NVRAM memory.
To perform a super NVRAM init
1.
Turn off the all-in-one.
2. Press and hold down the * and 5 buttons.
3. Continue to hold down the buttons while you turn on the all-in-one. Hold the buttons throughout
the entire power-on sequence.
4. When Permanent Storage Init. appears on the control-panel display, release the buttons.
5. When prompted, set the language and telecom country/region.
6. Allow the all-in-one to return to Ready before using it.

Posted on Oct 30, 2008

  • jimbeb Mar 25, 2011

    03-24-2011 07:54 AM Just had the same problem. Dispaly in German after selecting English-Europe. Hp support had no answer after 25 mins on the phone. Finally solved it myself. This is for a Deskjet 3050 1) Remove power cord. 2) Press and hold together Cancel button and OK button ( OK button is the one at the very bottom). 3) Reinsert power cord to rear of printer while holding in both of these buttons for about 20-30 seconds. 4) The HP sign should come onto the dispaly. This should reset the dispaly screen back to factory settings. You will have to reconnect your wifi again. This worked for me. Good luck.

  • obebrooke
    obebrooke Mar 04, 2013

    Thank You so much, I've been sitting here for two hours trying to find the solution without doing a down load.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Suddenly my Facebook looks like Russian. How to get it to return to English?


you may have changed your primary language to russian.
regardless of the language used, you may still be able to find the setting to change it back, since the locations of the settings would not have changed..
if you use google chrome, you could easily ask it to translate the page automatically back to english for you.. and then navigate to My Account - Settings - Language - & choose english as your primary language.
Alternatively, this link shows how to change to dutch/german, but is included as a guide to getting to the language settings page only. http://www.itechnobuzz.com/freebies-f-secure-antivirus-2011-1-year-free-license-key

Sep 30, 2015 | HP Computers & Internet

2 Answers

Need to change language to english/us


is it windows 7 home basic?if it is the only way to change language legaly is to upgrade to ultimate as that has all the languages.there is a programme you can run but it does not change the language of the op system.eg windows 7 dutch would be changed to english but updates will still be dutch.if its ultimate download the language pack from windows update.

Dec 06, 2013 | Acer Computers & Internet

2 Answers

My printer language has been changed accidentally, pls help me to change it to english language. send me how to change using the control panel.


Hi vivekchat18,

The instruction below will help you put back the display language you desire for your printer. You may use the procedure below to print out reports or to show messages on the all-in-one control panel. Here's how:

1.First you need to press MENU.
2.Then, select SYSTEM SET UP.
3.Afterward, select LANGUAGE.
4.Now, choose the language that you prefer. In your case, ENGLISH.
5.You have to SAVE your settings.
6.Finally, wait until your system automatically restarts.

Hope it helps.

Thank you for using Fixya.

Mar 29, 2011 | HP LaserJet 3050 All-In-One Printer

1 Answer

Hi, I have bought HP Deskjet 3050 all in one printer and it's not in English how can i change the language display? Thankyou.


You will need to perform a reset on the machine.

1. Turn off the all-in-one.

2. Press and hold down the * and buttons.

3. Continue to hold down the buttons while you turn on the all-in-one. Hold the buttons throughout

the entire power-on sequence.

4. When Permanent Storage Init. appears on the control-panel display, release the buttons.
5. Allow the all-in-one to return to Ready before using it.

Once it resets it will prompt you to set the language, use the arrow keys to select English and then press the checkmark. Unit will restart in English mode.

Mar 11, 2011 | HP LaserJet 3050 All-In-One Printer

1 Answer

I have just brought the HP DESKJET 3050 all-in-one J610 SERIES and the language setting is in german on the display of the printer. How do i turn it back to english?


Hi amandajane30,

The instruction below will help you put back the display language you desire for your printer. You may use the procedure below to print out reports or to show messages on the all-in-one control panel.

Here's how:

1.First you need to press MENU.
2.Then, select SYSTEM SET UP.
3.Afterward, select LANGUAGE.
4.Now, choose the language that you prefer. In your case, ENGLISH.
5.You have to SAVE your settings.
6.Finally, wait until your system automatically restarts.

Hope it helps.

Thank you for using Fixya.

Jan 01, 2011 | HP LaserJet 3050 All-In-One Printer

1 Answer

Language is Dutch - I need English (USA)


if you do a reset (hold reset for 10 seconds )it should go through the mains setting before starting the navcore.

Sep 24, 2009 | Tomtom ONE GPS Receiver

1 Answer

Need to change language settings on Samsung Omnia


yes you can......the question is do you understand dutch?? :D take it to were you got it from and tell em the language is in dutch..they'll probably find somebody

Sep 05, 2009 | Samsung SGH-i900 Omnia Unlocked Cellular...

2 Answers

3050 All-In-One Printer


how do I change the language? everything is in German.

Nov 11, 2008 | HP LaserJet 3050 All-In-One Printer

Not finding what you are looking for?
HP LaserJet 3050 All-In-One Printer Logo

976 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Seeker5211
Seeker5211

Level 3 Expert

1089 Answers

kakima

Level 3 Expert

102366 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...