Question about KitchenAid KWCU265HSS Kitchen Hood

2 Answers

Schematic for AP3105889

Hello everyone,

I'm wonder anybody has a schematic or the part list for this part number AP3105889, it made by WHIRLPOOL ,and here is the link for it.

If anyone has it please post it in here or you can email me at:, thanks you very much and have a wonderful day.

Tony N.

Posted by on


2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 99 Answers

You can try this site, it has questions and answers, maybe it has an answer to your question,

What is the model number?

Posted on Apr 21, 2017

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

What is it you are trying to do? Are you trying to repair the one you have so as to not purchase a new one? Do you need help hooking up the correct wires? Your question is unclear so any additional detail would be helpful.

Posted on Apr 09, 2017


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: KitchenAid KSM90 gear stripped?

I just ran into this problem when the PLASTIC worm gear broke and then the mixer would not power on after I replaced the gear. The problem was due to the was I tried to dissasemble the mixer. I removed the two plastic screws near the top center of the mixer when attempting to disassemble. These do not have anything to do with the assembly it turns out the attached square pieces (attached to these screws by springs) must be in the proper orientation to run. I put them in the way it showed in a diagram but it did not work until I tried all four different combinations that they could be rotated. Two of the rotations on the square could be eliminated by closely looking at the end where it contacts the shaft. The round shaft marking will be evident on the square inserts. I'mnotsure how to better describe them, but the are attached by springs to the plastic screws on both sides of the top of the mixer.

Posted on Dec 19, 2008

  • 188 Answers

SOURCE: kitchenaid K5-A ...need wiring schematic

RE: Wiring for KitchenAid K5-A (before the solid-state control).



Posted on Aug 09, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Whirlpool refrigerator GI6FDRXXY00 K04067098 I have migrated to the Philippines and brought my whirlpool GI6FDRXXY00. Recently this broke and the whirlpool service center here have instructed me to...

Link to Sears Parts Direct User manual and parts diagrams parts lists and repair help.
WHIRLPOOL Refrigerator Parts Model GI6FDRXXY00

Note that sears offers repair help. You might even get them to email a schematic. You don't have to tell them where you are.

Youtube has many refrigerator help videos.

Oct 26, 2014 | Refrigerators

1 Answer

Wiring schematic for whirlpool dryer 3rleq8033rw

Your wiring diagram is a part number 8299807, usually not avail separately, if still present it's behind the control panel. Disconnect power, remove the screws that hold the rear steel panel on to the front control panel, it was placed there from the factory. Pleazer Appliance...

Oct 11, 2014 | Whirlpool Dryers

1 Answer

Schematic diagrams

8272124 that's part number for lid switch. Amazon I'm sure has far as schematic . There's one taped to inside front of cabinet. Or visit under customer service heading is a link to manuals

Aug 27, 2014 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

86 audi 5000CS speaker wiring

You're in luck. This guy has every electrical schematic listed for the 5000:

Jan 21, 2013 | 1985 Audi 5000 S

1 Answer

I need the wiring schematic for a whirlpool imperial series dryer

Should be a small envelope or plastic bag inside the machine with the wiring schematic folded up inside. Often includes timer pin outs, and parts list. Usually inside the control panel, but sometimes elsewhere inside the cabinet.

Dec 09, 2009 | Whirlpool Dryers

1 Answer

Amplifier schematic diagram

Hi Janet,

If you get back to me with your email address I will scan the schematics and email them to you.

Alan Hood

Mar 13, 2009 | Wurlitzer Jukebox 1015 One More Time...

4 Answers

Where can i find schematic diagram of whirlpool refrigerators?

there's no cool air coming into the freezer or refrigerator sections. as soon as it starts there is a clicking sound and it stops. what's the problem? the fan works at the back. i've cleaned all the coils below. thanks

Dec 09, 2008 | Whirlpool GD2SHGX Refrigerator

Not finding what you are looking for?

Open Questions:

0 Answers

Fan not working The fan on the hood stopped working (i.e., nothing happens when I turn it on). From this wiring diagram:, you can see that the hood has two circuit boards. One for slided switches and speed control (Part Number: AP3133509 made by WHIRLPOOL), and one for motor control (Part Number: AP3105889 made by WHIRLPOOL ). My best guess was that the motor control board went bad, so I ordered a new motor control board to replace it. You will see five wires coming out of the speed control portion of the first board. The white wire goes directly to the fan motor, but the other four (blue, orange, black, and black), go to the motor-control board which also has four wires of the same colors. OK. Blue to blue, orange to orange. No problem. But what about the two black wires coming from the speed controller and going to the two black wires on the motor-control board? Does it matter how these are connected? I figured if it mattered, they would also be color coded, so I just connected black to black, black to black (random order). When I turned on the fan, it blew out my new motor-control board. I have a new motor-control board. I was going to try reversing the two black wire connections, but don't want to blow out another board. So, my question is, do you think it is important to match a specific black wire on the motor-control board to a specific black wire coming from the speed controller? It seems strange to me that it would work this way, as these wires snake around through the hood, and it virtually impossible to tell which is which when when they reach the motor-control board. I don't know how they would be been matched during original assembly. But I can't think of any other problem. By the way, I was able to by-pass the motor-control board and run the fan directly, so I don't think the problem is with the fan motor. I have also replaced the control board used for the slider switches and speed control, so the problem is not there either. Thought welcome. Thanks. jp

Oct 17, 2008 | KitchenAid KWCU265HSS Kitchen Hood

KitchenAid KWCU265HSS Kitchen Hood Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Kitchen Ranges Experts


Level 3 Expert

77939 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a KitchenAid Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides