Question about Hitachi CP-X275 Multimedia Projector

1 Answer

Picture not square

MY PROJECTOR IS 4M FROM THE SCREEN. THE PICTURE IS WIDER AT THE BOTTOM THAN ON THE TOP. I HAVE CHANGED THE PICTURE TO ALL SISES BUT THE PROBLEM IS THE SAME ON ALL 3 SETTINGS. THE PICTURE QUALITY IS PERFECT.
HERE ARE THE SCREEN DIMENSINS. I HAD IT CUSTOM MADE FOR MY HOME.2640MM X 1360MM. PICTURE FITS PERFECT ON BOTTOM (2640MM) BUT SLANTS INWARDS TOWARDS THE TOP OF THE SCREEN I WOULD SAY BY ABOUT 50MM ON EITHER SIDE.
PLEASE HELP
GAVIN

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Keystone should help in your opinion. adjust the keystone and the picture should be a square then.

Posted on Sep 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My projector has worked fine for a while now, but for some reason it now has a greenish glow in the bottom left to about the middle. i it was 4 squares, it'd be the bottom left square. The cable has


Hello!
Any picture imperfection in any LCD projectors is caused by light engine's damage. It could be due to constant overheating, dust accumulation, etc.
In any occasion, the light engine must be replaced or repaired(if possible).
If that glow is not substantial yet and you can live with that, just ignore it. It will get worse, eventually, then you will think over: to repair this projector or replace it with a new one.
good luck,
thanks,
Alex.

Dec 20, 2011 | Panasonic PT-LB60NTU LCD Projector

1 Answer

Dark side of screen


the light tunnel has collapsed and needs replacing. the part is inexpensive and relatively easy to replace. if you can get the part from infocus or an authorized service center (part # 306-0095-01), remove the top (4 brass screws and 4 silver screws on the bottom, 2-3 silver screws on the back), next to the lens is the colorwheel. remove the 2 black screws on the colorwheel base, 2 black screws on the metal tunnel frame side, remove the tunnel glass. replace, and reverse the instructions to put it back together.

Aug 15, 2009 | InFocus ScreenPlay 4805 Multimedia...

1 Answer

Slanted Border- Projector image is not square


Is the image slanted on the bottom as well?
Make sure the projector's throw is pointed directly at the target ie. screen or wall etc. there's not much else it could be.

Jan 10, 2009 | InFocus ScreenPlay 4805 Multimedia...

1 Answer

INFOCUS Screenplay LCD projector...


Hi there

I take it the Projector is ceiling mounted ?

If this is the case check that it is installed with the lens of the Projector in the facing straight to the middle of the screen or try adjusting the bracket's swivel head to move it a bit - should do the trick !

May 10, 2008 | InFocus ScreenPlay 4805 Multimedia...

2 Answers

Bad lines on Infocus IN24 images


Hi Dan

The only way to get rid of this is to either have the Mianboard repaired or replaced.

If the Projector is stil under warranty - it will cover it.

If not - It is quite expensive !

Hope this helps you.

Nov 24, 2007 | Multimedia Projectors

2 Answers

The picture become upside down


You need to change it to front/ceiling in the menu function of the projector.

Oct 03, 2007 | Epson PowerLite 62c Multimedia Projector

Not finding what you are looking for?
Hitachi CP-X275 Multimedia Projector Logo

347 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hitachi Multimedia Projectors Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

5605 Answers

The Knight
The Knight

Level 3 Expert

68153 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Hitachi Multimedia Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...