Question about Televison & Video

1 Answer

How to programme a nova 4 button remote on a gemini gate motor

Programme

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It's important to know that the Nova remote controls are not compatible with the Gemini gate motor. In order to get these remote controls to work with your Gemini gate motor, you'll need to install a Centurion receiver first (see http://www.centsys.co.za/upload/product_link_files/CS37_Nova_Receiver_Instructions_1031.D.05.0012_4.pdf). Once the Centurion receiver has been installed on your Gemini gate motor, follow the programming instructions as per the leaflet that accompanied your brand new Nova remote control, or download the instructions from http://www.centsys.co.za/upload/product_link_files/English_Transmitter_InsertCS37_1031.D.02.0027_1_Nova.pdf

Posted on Jul 11, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: I have bought an additional

Steps to Programming Centurion Nova Remotes


1. Unlock the motor cover with your Centurion Key, remove this cover.

2. Inside the perspex enclosure there is a small Receiver Board (approx size of a matchbox), identified by wording CENTURION CP9Z, also has the wording J1-Learn; J2-Erase.

3. There will be a small 'shunt' placed on one of the pins labelled J1, J2 or the centre pin - these are the 'Learn' pins.

4. Remove this shunt and place it over (or bridge) the J1 and centre pin together. The red LED Status light, to the left of the Learn Pins will illuminate.

5. Remove the new Remote/Transmitter from its packaging, hold down the required button once and the red LED Status light on the Receiver Board will flash once indicating that the button has been learned. As soon as the light has flashed, remove your finger from the button.

6. If further Remotes/Transmitters are to be added to the system, repeat step 5.

7. Ensure that you now remove the 'shunt' and place it back onto the blank or J2 pin - do not leave it bridging two pins.

8. Close the enclosure, place the motor cover back onto the motor and lock in place.

Posted on Nov 03, 2010

  • 1 Answer

SOURCE: Gemini Universal Remote Control No. G410S

Managed to buy a new remote control.

Thank you.

Posted on Sep 02, 2009

  • 1 Answer

SOURCE: Need to program Nova remotes on a Centurion D5 Motor.

Download the manual here http://www.centsys.co.za/support/manuals/pdf/1031.D.05.0023_1.pdf

Posted on Apr 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

MY ELITE SL 3000 UL WILL NOT WORK WITH REMOTE. IT WILL WORK WITH THE LOOP. PROBLEM WITH BATTERY OR NEED TO REPROGRAM THE REMOTE, IF SO WHERE IS THE LEARN XMITTER LOCATED PLEASE HELP


Hi Mary, do you have more than one remote for the gate? Your remote needs to be paired with the gate receiver. Normally you need to push a certain button on the control panel to enable learning mode then you press the remote button you want to use. You will have to follow this learning process for your device. Please keep in mind that just any remote will not work with your gate, it needs to be on the same frequency and use the same modulation mode.
Hope this helps.

Oct 28, 2014 | Elite Sl3000 1hp Slide Gate Motor,...

1 Answer

Gemini gate motor


Check if it has stops anywhere in the system, usually there are micro switches that are activated by arms, etc that tell it how far to open and close. You may need to adjust them.

Aug 20, 2014 | Cars & Trucks

1 Answer

How to programme a digikey 4 button remote on a centurion d3 gate motor


You may have this posted in the wrong product category. Please select another category appropriate to the problem and re-post the problem so the correct expert will see and respond to the question..
This is for car and truck problems.
This post can't be removed or moved, please re-post the question in the correct product category. Thanks

Oct 08, 2012 | Cars & Trucks

1 Answer

I have bought an additional remote which I must programme with my centurion sliding gate motor. I need some assistance, but I don't want the other remotes to go out of sync. Please assist. Thanx Dawie


Steps to Programming Centurion Nova Remotes


1. Unlock the motor cover with your Centurion Key, remove this cover.

2. Inside the perspex enclosure there is a small Receiver Board (approx size of a matchbox), identified by wording CENTURION CP9Z, also has the wording J1-Learn; J2-Erase.

3. There will be a small 'shunt' placed on one of the pins labelled J1, J2 or the centre pin - these are the 'Learn' pins.

4. Remove this shunt and place it over (or bridge) the J1 and centre pin together. The red LED Status light, to the left of the Learn Pins will illuminate.

5. Remove the new Remote/Transmitter from its packaging, hold down the required button once and the red LED Status light on the Receiver Board will flash once indicating that the button has been learned. As soon as the light has flashed, remove your finger from the button.

6. If further Remotes/Transmitters are to be added to the system, repeat step 5.

7. Ensure that you now remove the 'shunt' and place it back onto the blank or J2 pin - do not leave it bridging two pins.

8. Close the enclosure, place the motor cover back onto the motor and lock in place.

Aug 28, 2010 | Televison & Video

2 Answers

Need to program Nova remotes on a Centurion D5 Motor.


Hi
Have you managed to program the remotes

Sep 07, 2009 | Televison & Video

1 Answer

GEMINI CL033


Code available for free at this address:

http://www.remotecentral.com/cgi-bin/files/rcfiles.cgi?area=other&db=devices&br=gemini

Hope that helps,

erch.

Mar 17, 2008 | Gemini Sound Products SBR3B Remote Control

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

1,056 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74459 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...