Question about Westclox 118861 Nova Clock Radio

Open Question

IP:G8 This is actually a question about our Westclox 1188 Alarm Clock. It was sitting on a night stand where water was spilled, and now the time display reads "IP:G8". I cannot seem to change the display. Any ideas? Thanks!

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: Westclox Monarch Alarm Clock - Model No. 90003

While holding down the snooze bar that says "ALARM" on it, hold down either of the "HOUR" button to set the hour when the alarm should go off or hold down the "MINUTE" button to adjust the minutes for when the alarm should go off.  Switch the "ALARM" to "ON" when done.  

Posted on Sep 03, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set alarm for Westclox 47550 Quartz?


Hi, A 8 year old can do this. On the back of the clock there should be 2 round turning nobs. 1 is for to set time (min...) 2sec is for to set timer for that hour...usually is a smaller hand on face of clock.
select hour to wake up at and set alarm Button. This is only basic set up.

Jan 13, 2014 | Westclox 47550 Quartz Loud Bell Analog...

1 Answer

How do i set year on westclox 70034 alarm clock?


You need to make certain that you have set the year right, otherwise it will show the correct day for say 2011, rather than 2013.

Jul 14, 2013 | Westclox LCD Dual Alarm Clock with...

1 Answer

I have 3 westclox clocks I have lost the instructions to set them. atomic clock Westclox 70026 cannot change the zone nor can I set the time to alarm


Manual on the link below.
If you would like to see the instructions, they are in .jpg format:

Front page of instructions:
http://www.poyntsource.com/New/Pathimages/westclox%2070026%20-%20page%201.jpg

Back page of instructions:
http://www.poyntsource.com/New/Pathimages/westclox%2070026%20-%20page%202.jpg

You might want to save these images on your computer in case the webpage is no longer available.

Oct 13, 2011 | Audio Players & Recorders

2 Answers

CRA108: I can not set the time. I hold in the time button down while pushing the hour and/or minute button but nothing happens. The clock actual is displaying a time that is not proper. It currently...


My Coby CRA108 starting doing this after 6 months of use. Although I described the display as 1P:C8 since there is no key to properly display the character (hybrid of a G & C). I've left it unplugged and changed the backup battery with hopes it would reset. No luck so far. Anyone have success???

Jan 07, 2011 | Coby CRA108 Clock Radio

1 Answer

Digital clock gains time


digital clocks work of the frequency input of the power source so it is possible to have it adjusted by a technician
like fine tuning a radio frequency there may be a pot that can be tuned to mains frequency exactly
talk with technicians in radio or tv shops or possible some jewellers who work on electric clocks may help

Nov 26, 2017 | General Time Corporation Westclox Bell...

1 Answer

Westclox Travel Alarm


After selecting either TIME, DATE, or ALARM at the top of the screen, use the stylus to touch and hold the large time display. Hold it there for about 5 seconds and the clock will beep and the time display will start flashing. Then you can touch either the hours or minutes and it will increase by either 1 hour or 1 minute accordingly. When the DATE is selected, it shows the year in the large display. Again, holding the stylus on the year diaply for about 5 seconds will enter into the chqange mode. IN all cases, to exit the change mode simply select one of the other selections across the top: TIME, DATE, ALARM.

Jun 30, 2008 | Audio Players & Recorders

2 Answers

Westclox Monarch Alarm Clock - Model No. 90003


While holding down the snooze bar that says "ALARM" on it, hold down either of the "HOUR" button to set the hour when the alarm should go off or hold down the "MINUTE" button to adjust the minutes for when the alarm should go off.  Switch the "ALARM" to "ON" when done.  

Apr 22, 2008 | Westclox Audio Players & Recorders

2 Answers

Westclox model 22717


Hi faulkquarter

I take it that the clock displayed with this problem if not a 22717 model. The one I have sighted is a digital clock. Generally, you need to hold down the "time" button and also press the "hours" and "mins" buttons at the same time to set the time. If this is not how your clock appears, please give me the button names and I can write a method of changing the time for you.

regards
Graeme

Apr 14, 2008 | General Time Corporation Westclox Bell...

1 Answer

Alarm


Contact these guys; http://www.westclox.com/control/contactus They sell and support the Sonatina, but don't have a manual online. Hope this helps :)

Sep 01, 2006 | Westclox Sonatina Clock Radio

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Westclox Audio Players & Recorders Experts

pawnpower

Level 3 Expert

504 Answers

 Grubhead
Grubhead

Level 3 Expert

5508 Answers

ka4iup
ka4iup

Level 3 Expert

3960 Answers

Are you a Westclox Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...