Question about Nordic Track Nordictrack Apex 4100i Treadmill User Part Manual

Open Question

I have a Nordic track apex 6100xi and the incline won't go up and down anymore. Help!

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Gackmaster
  • 12 Answers

SOURCE: I have a Nordic Track EXP1000i Treadmill. The

I know it's been months, but, if you still have this problem try this: 1. remove the philips screws holding the motor/belt/electronics cover on: you can lay the whole thing on it's side and remove them from the bottom. there's two in the front and two on the sides.
2. Obviously, unplug the unit! before doing anything. lay the unit back on it's feet (normal position)
3. Find the incline motor assembly. it will be int he middle of everything. black tube thingy.
4. take a cordless drill with a flat head screw driver bit, and turn the incline motor CCW. until the bed is flat.
5. what what I have read, you should shop for a new incline sensor. these fail before the motor does.

Posted on Jan 26, 2010

  • 40 Answers

SOURCE: i have a nordic track a2350,and the incline wont

I've seen this problem several times, but many things can cause it. It's most likely the motor control board, but it could be a number of things. I'd have it looked at.

Posted on Oct 25, 2009

  • 103 Answers

SOURCE: I have a nordic track a2350 and the belt stopped

This is usually related to the control pwb which is located under the motor "hood".
You can get this part from iconservice.com by going to the replacement parts section of the site and entering the model number of your machine, Which is located on the lower frame assembly below the walk belt. After you have receieved the part you can follow this procedure to repair it.

http://www.fixya.com/support/t3807308-belt_goes_full_speed_when_started_shuts

Posted on Jan 06, 2010

Gackmaster
  • 12 Answers

SOURCE: I have a Nordic Track EXP 1000X treadmill and the

Probably 85% of the time, it's the sensor.



1. remove the screws from the bottom of the enclosure case. 2 or 3 in the front and 1 on each side

lay it back down, and power it up, and actuate your incline. watch the end of the motor, to see if the shaft is moving. It probably IS turning but only a little bit. NOT enough. In this case I'd say it is the sensor.

2. Unplug the unit of course.
3. the incline motor is in the middle of the pack,..you'll see a black tube looking thing sticking up.
4. on the bottom side of this, you will see,..or feel for a black square sensor attached to bottom of the motor casing.
5. follow the wires and unplug this.
6. pry it off with a screw driver. Remove incline assembly, if you cannot reach it.
7. replace sensor and try it again.

if the MOTOR does NOT turn when using the incline buttons, the problem backs up to possibly a bad control board. or a bad motor on your incliner, however, i'd say that's the last thing to go.

Order of failure: 1. sensor 2. control board 3. motor.

good luck

Posted on Jan 26, 2010

maxtreadmill
  • 832 Answers

SOURCE: manual for a Nordic Track Personal Performance

Go to iconservice.com click on to manual Input manufacturer : Nordic Track then model # NTL349050 and you manual await you.

Posted on May 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does incline go up and down when you turn on treadmill?


The sensor or relay is stuck, it's an easy fix with electronic contact cleaner, if you can access the part's ?

Feb 21, 2015 | Nordic Track Nordictrack Apex 4500...

1 Answer

My incline motor stopped working on Nordic tracap apex5100


unplug unit and remove the motor cover. there are two bolts that hold the incline motor in. one on top of unit and the other on the bottom of the lifting screw. make sure incline is all the way down. follow the wiring to the control board. removed them off the board noting which ones go where and color orientantion. instillation is reverse of removal

Sep 04, 2014 | Nordic Track Nordictrack Apex 5100...

1 Answer

What is the phone number for Nordic Track Support desk?


NordicTrack Customer Service Department at 1-877-993-7999.

Sep 04, 2014 | Nordic Track Nordictrack Apex 6100xi...

1 Answer

How do I fix my Nordictrack Elite 7500? The incline is stuck and won't move up or down.


1) Lube the elevation motor, see the diagram, parts gear + shift
2) adjust the POT, for a little and see if there are better improve.
3) RUN the software calibration for diagnose, troubleshooting, fix it.
God bless you
7_10_2012_12_38_54_pm.jpg7_10_2012_12_39_27_pm.jpg

Jul 09, 2012 | Nordic Track Exercise & Fitness

1 Answer

Panal problems


1) adjust the reed swithc, clean, and tight the wire connector.
2( see the block diagram

6_20_2012_3_19_29_am.gif6_20_2012_3_19_49_am.gif

Jun 19, 2012 | Nordic Track Nordictrack Apex 6100xi...

1 Answer

Nordic Track X5 belt won't move


1) Lube the deck belt, this happen because the electronic system protect the system and shut down.the cause is deck worn.
2) Lube the rollers bearing too.
3) Measure the input voltage motor, if there are the motor need repair.
4) Measure the output voltage board, for input voltage motor, if there are Not the board is faulty.
God bless you
6_13_2012_5_06_25_pm.gif6_13_2012_5_06_59_pm.jpg

Jun 12, 2012 | Nordic Track Exercise & Fitness

1 Answer

My nordic track apex 6100 xi all of the sudden won't run...or walk...at all? HELP!


Dear Sir:
This is probably a 1) faulty speed sensor or 2) the speed sensor is not plugged in properly. Its also possibly a 3)faulty motor control board or lower board.4)the drive motor is faulty 5) The drive belt is broken.6) Resent c.breaker 7) Test the power cord. 8) Reset the c. breaker from your home. 9) Do not use extension cord .

Adjust the speed sensor see the diagram, and RUN your software calibration for easy diagnose and troubleshooting. read your user manual.
sincerely. God bless you.

ernesto cuadra
managua, nicaragua. c.a

2_17_2012_12_15_47_am.gif

Feb 11, 2012 | Nordic Track NordicTrack Elite zi...

1 Answer

Nortrak 4100i wont go up or down


hold down stop and speed + then put safety key on
hit stop once
push incline+
let it go up and down
take key off and reattach
try
if it still doesn't go the incline motor is bad

Aug 07, 2010 | Nordic Track Nordictrack Apex 4100i...

2 Answers

Nordic Track exp 2000I. Consol lights, buttons do not work.


If the console lights up but the buttons don't work, then unfortunately it's probably the console and they're not repairable that I know of. You may want to check the wiring harness and the connections at the console and at the controller under the motor hood. Pull them apart and check for bent pins. If they look good, the console is most likely bad.

Mar 04, 2010 | Nordic Track Nordictrack Apex 4100i...

Not finding what you are looking for?
Nordic Track Nordictrack Apex 4100i Treadmill User Part Manual Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nordic Track Exercise & Fitness Experts

Matt Olenzek
Matt Olenzek

Level 2 Expert

293 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Paul Sikkema
Paul Sikkema

Level 2 Expert

171 Answers

Are you a Nordic Track Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...