Question about Stanley Bostitch Sb 2IN1 2 In 1 Narrow Crown Stapler/18 Gauge Brad Nailer

Open Question

How to load staples into brad nailer - Stanley Bostitch Sb 2IN1 2 In 1 Narrow Crown Stapler/18 Gauge Brad Nailer

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 142 Answers

SOURCE: My brad nailer shoots staples without any problem

the only suggestion i have is that you may have a feed problem, so i would clean and lube the track the nails run on

Posted on Mar 27, 2010

  • 1383 Answers

SOURCE: Stanley Bostitch Sb 2IN1 2 In 1 Narrow Crown Stapler/18 Gauge Brad Nailer Logo Stanley Bostitch Sb 2IN1 2 In 1 Narrow Crown Stapler/18 Gauge Brad Nailer owner manual

Stanley Bostitch has been sold to Dewalt. The link below has all the information and parts for your gun. Good luck with your projects.

http://servicenet.dewalt.com/

Posted on Jul 21, 2012

  • 4 Answers

SOURCE: My brad nailer shoots staples without any problem

Shoots staples fine but brads jam or bend. Check that the part called "guide bar", #35 on the parts diagram isn't getting stuck in the channel of part #30.

The guide bar retracts into the channel when driving a staple and springs out of the channel to guide brads.

The guide bar can get stuck in the channel if it's bent or gummed up. (Bent is likely the result of driving a brad into an obstruction.)

d2e88e7c-278a-4fed-8537-9a3a88d8d2ae.jpg

Posted on Mar 30, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I load the stapler?


No you don't. We answer most things here.

If the stapler is like any of these

http://www.amazon.com/s?ie=UTF8&page=1&rh=i%3Aaps%2Ck%3Abostitch%20staple%20gun

You push the back in slightly to unlatch it and then drop it down a bit and the staple pusher comes out completely.

Jan 28, 2016 | Heavy Duty Stanley Bostich Heavy-duty...

1 Answer

HOW TO LOAD BRADS IN STANLEY TRE500


Please download the instruction sheet from the following link which explains how to load the brads. Make sure you have the correct size of brads mentioned at the bottom of the instruction sheet.

TRE500 Sharpshooter Stapler Instruction Manual

Aug 13, 2014 | Electric Stanley Tre500 Staple Gun /...

1 Answer

What gage staples do I need for a p300 ryobi air stapler?


Good morning Victoria,

The staple series that you'll need is probably need is a 90 series. These are again an 18gauge wire in several different lengths.

Regards
collatedfasteners

Jul 05, 2014 | Ryobi P300 One+ Stapler Brad Nailer

1 Answer

What kind ryobi p300 staples & brad nails


Nice little nailer Fred. Here are the details (sold at Lowes or other lumber centers).

Staple Size 3/8 in. Crown Width, 1/4, 5/16, 3/8, 1/2, 17/32, 9/16 in. length
Brad Size 18 gauge, 3/4, 1, 1-1/4 in. length

Magazine capacity 100 staple/brad Good luck with your projects

Oct 14, 2011 | Ryobi P300 One+ Stapler Brad Nailer

1 Answer

What kind staples p300 stapler brad nailer


Staple Size 3/8 in. Crown Width, 1/4, 5/16, 3/8, 1/2, 17/32, 9/16 in. length
Brad Size 18 gauge, 3/4, 1, 1-1/4 in. length
Magazine capacity 100 staple/brad

These are sold at Lowes and other lumber centers.

Oct 14, 2011 | Ryobi P300 One+ Stapler Brad Nailer

1 Answer

How to load brads into stanley tre 550 electric staple/brad nail gun


HOW TO USE YOUR ELECTRIC STAPLER/NAILER
TO LOAD STAPLES

1. Unplug tool, (fig. 1)...(place on/off switch in "off" position, (fig. 2).)
2. Place on/off switch in "off' position.
3. Select proper staple length.
4. Use only staples identified by stock numbers on next page. Substitute staples may cause jamming.
5. Hold tool upside down. (Squeeze latch and pull, (fig.3).)
6. Drop staples in channel, legs facing upward. Push latch back in to lock in place, (fig. 4).

TO LOAD BRADS

1. Unplug tool, (fig. 1)...(place on/off switch in "off" position, (fig. 2).)
2. Use only brads identified by stock numbers on next page. Substitute brads will cause jamming.
3. Look for the image of a brad nail on the front side of the tool (fig. 5). Load brads into this side only.
4. Hold tool upside down (Squeeze latch and pull, (fig. 3).)
5. Drop brads into the channel, tilt the tool so the brads lay against the channel wall, (fig. 5).
Push the latch back in watching that the brad strip does not fall over.
6. Use High/Low power when driving brads.


TO STAPLE OR NAIL

1. Make sure the on/off switch is in the "off" position, plug stapling tacker in.
2. Turn tool on by switching to position 1 which is the "on" position and hold firmly against work surface to
engage safety mechanism.
3. Apply adequate pressure on the top of the knob (fig. 6.) while the trigger is pulled.

You can find the figures mentioned above at the following link:

http://bdk.force.com/FAQ/servlet/fileField?retURL=%2Fapex%2FPKB_Article%3Fid%3DkA0C0000000CdtPKAS%26brand%3DStanley%26returl%3D%252Fapex%252Fpkb_search%253Fbrand%253DStanley%2526mode%253D0%2526model%253D%2526sortby%253D0%2526terms%253DTRE550&entityId=ka0C0000000CdqqIAC&field=File_1__Body__s

Jun 20, 2011 | Stanley Tools TRE550 Electric Staple/Brad...

1 Answer

We don't know how to put in new staples. We r fixing a chair


If your brad nailer is a BN200; I don't believe it will accommodate staples.

Feb 14, 2011 | Porter Cable 18 Gauge 2 " Brad Nailer Kit...

1 Answer

The gun will fire staples, nails do not set.


Shoots staples fine but brads jam or bend. Check that the part called "guide bar", #35 on the parts diagram isn't getting stuck in the channel of part #30.

The guide bar retracts into the channel when driving a staple and springs out of the channel to guide brads.

The guide bar can get stuck in the channel if it's bent or gummed up. (Bent is likely the result of driving a brad into an obstruction.)

The business end should look like this:

37b60e82-3010-4c4e-9065-d56a1df32d57.jpg

Mar 07, 2010 | Stanley Bostitch Sb 2IN1 2 In 1 Narrow...

1 Answer

How do I load staples? I can not find my manual!


On the back bottom of the stapler there is a rod you need to lift up and then pull out on it should come out

Nov 15, 2009 | Arrow No.ETF50PBN Extra Heavy Duty...

1 Answer

The door at the back of the staple gun won't close


You may have too many staples loaded in the magazine.

Jun 05, 2009 | Arrow No.ETF50PBN Extra Heavy Duty...

Not finding what you are looking for?
Stanley Bostitch Sb 2IN1 2 In 1 Narrow Crown Stapler/18 Gauge Brad Nailer Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanley Air Tools & Compressors Experts

John Trevino

Level 3 Expert

1383 Answers

Joe Garcia
Joe Garcia

Level 2 Expert

205 Answers

River bottom

Level 2 Expert

174 Answers

Are you a Stanley Air Tool and Compressor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...