Question about Mitsubishi WD-62525 62" Rear Projection HDTV

Open Question

Mitsubishi DLP lookng for schemtics I have the manual

Looking also where I can find replacement boards. hope I can get some online training on repair. I've heard there is a place I can send in boards to have repaired. have a number of these tvs all are starting to have problems with caps have done replacement on most of them have a couple that it did not help. would like to fix them like this tv have both 52 and 62 in models. any help out there. I know about the diode fix I posted it. Thanks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

premtech
  • 934 Answers

SOURCE: Mitsubishi ws-55513 green flashing light issue

I would asssume that the four cap replacement you're referring too is in the power supply of the DM module. (The large silver looking box on the left looking at the back of the TV)..
You can unplug that module from the signal board and remove it. Open the cover and you should find 4 16v caps in the power supply. If they look buldged chances are they are the failure. If not you might want to take an ESR meter to them to confirm they're okay and move on... In the back of that module is a small vertical board called the E2P module. Unplug it from the DM and plug the DM back into the signal board. If it powers up your picture might not be in the best alignment but you've identified the problem - just replace the E2P module.
If none of this works you're going to start getting into some greater technical requirements - but let's cover that when you get that far...
Bill

Posted on Dec 28, 2007

MikeMaierTV
  • 206 Answers

SOURCE: Mitsubishi 52 " model WD-52631

Nope the bulb is fine. This set sucks up dust and contaminates the light engine. Rarley does blowing the set out with compressed air fix this, The light engine can be disassembled and cleaned but this is best left to someone who has done this once before. Because if it gets messed up you get to buy a $1500.00 light engine

Posted on Feb 13, 2008

  • 3422 Answers

SOURCE: Outer screen scratch

Hi,

You can try for the parts from HERE or from HERE

Goodluck,
Please don't forget to rate the solution.

Posted on Mar 27, 2008

Slinteriors
  • 8617 Answers

SOURCE: Mitsubishi WS-65807 blinks '22'

Jim,
yes the convergence Ics are what cause the two picos to be open they are both 5 amp picos. You can get the picos, the convergence ICs and the factory service manual for your model at the following link.your model is known as the V17 chassis for service manuals and you should require two STK392-570 Convergence ICs. Heres the link they provide free instalation instructions.
http://servicemanuals.vstore.ca/

Posted on Oct 02, 2008

  • 58 Answers

SOURCE: Blue Flickering Screen - Which Repair Kit?

2 swollen capacitors on the power supply (first board you can see on the chassis when you start to dissassemble) big caps... 3300 uf... 16v i think. these caps can also induce a 3.4 code (lamp error) and all around **** picture. fmt failures can range from black and white checkerboard pattern on the screen to wavy lines over the picture and also the blinking green light. DM failures I've seen include the blinking green light , wavy lines, and weird digital failures like horizontal bars green blocks or the picture being cut in odd places.

also when you hear that the failure is caused by the capacitors (blinking green light mainly) the culprit is not only the bulged caps. This is why you can change all the caps on the boards and still not have a working tv. its about 80 surface mount caps across both the fmt and dm. techs, look at your replacement boards and notice the darker print on the 47uf caps. good luck trying to change them it takes me about 3 hours to do both boards and about 45 dollars worh of caps.

Posted on Dec 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need dplclipfor mitsubishitv


I saw a video for this once. The problem is the DLP chip. It has to be replaced. Replacement DLP chips can be found online. The screen has white dots because some of the mirrors on the chip are bad. Be sure to have someone competent replace it. No soldering is involved. Book and manual will come with replacement. The DLP chip is delicate.

Mar 28, 2014 | Mitsubishi WD65737 65" DLP TV

7 Answers

Lamp will not turn on. I have (2) PJ458D DLP projectors. I took the lamp out of the projector that is not working and placed it in the other projector and everything worked fine. When I press the on off...


It sounds like an internal problem. How long have you owned the projector? How long have you been experiencing this issue? Once I have more information I can assist you further.
Thanks,
Lee

Sep 23, 2008 | ViewSonic PJ458D DLP Projector Multimedia...

2 Answers

After replacing the dlp chip in my mitsubishi tv there are vertical lines on the screen. any ideas?


i had the same lines on my 65' mitsubishi tv after replacing the DLP chip. after going back over everything i realized that the casinf that holds the chip in was not in the lock position. i took the chip out and replaced it then turned the little locking mechanism to the locked position. now my screen is perfect. hope this helps.

Nov 21, 2012 | Mitsubishi WD-60C9 60" DLP HDTV

2 Answers

Mitsubishi green blinking light of death


Hi Jim,

Green blinking light of death on Mitsubishi DLP TV means that the DM failed to booted up. I would advice you to replaced the 7 1000uf electrolytic capacitor on the DM board. Most of the time it fixed the symptoms. Please inquire at tvrepairworld.com if they have an available DM repair kit for V36 chassis (WD-57733 chassis).

Jdvillanueva

Jan 10, 2012 | Mitsubishi WD-57733 57" HDTV

2 Answers

I have white spots and black spots on right side of Mitsubishi WD-C657. I've done research online, and have heard its the dlp chip. Is that true, and if so, is it something that I can replace myself,...


This tv is it the DLP projection light engine block main board itself is the problems,not easily to go into the tv itself and replacing the IC chip itself.Must take out many mechanical parts to get u the Light engine block it self.U can replaced IC but somethime the IC chip it replaced,will not solved the problems,because the tv problems now the it is spreading and going on beyond the IC chip itself.If want to keep this tv very exspensive repair,i would reconmend hire a bound qualify tv tech replaced the whole Light projection block itself,but first call Mitsubishi for some kind of deal,they might help with the repair amount cost.

May 13, 2011 | Mitsubishi WD-C657 65" HDTV

2 Answers

Video went blank


It may be. I have replaced the lamp in my sony 3 times. Look for dlp lamps online and enter in your tv model. There are instructions online on how to change it yourself. They also show you in your manual. The power light should blink red indicating bulb failure. Read your manual. Hope that helps

Apr 26, 2010 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Buzzing noise from Mitsubishi DLP WD-52327 after replacing bulb


Did your replace lamp come on the screen or did you lose picture? Just because the LED indicator suggest replace lamp it doesn't mean it needs it. If your pix was dull or loss of brightness then replace it, if not then just reset your lamp timer, check your owners manual for instructions.

Feb 14, 2009 | Mitsubishi WD-52327 52" Rear Projection...

2 Answers

Blue Flickering Screen - Which Repair Kit?


yes they provide a free service manual with their kits. the symptom of the blue screen could either be the signal or the FMT as they can both cause those symptoms, My professional guess would be the signal board as the FMT will cause distortion lines across the screen with no picture.

Sep 25, 2008 | Mitsubishi WD-52525 52" Rear Projection...

2 Answers

Benq inverter board schemtic


Post me a picture of the board and I might be able to Help.Normally transistors 2Sc5707 are defective.
Samir.
viziks@gmail.com

Aug 20, 2008 | BenQ FP71G 17" LCD Monitor

2 Answers

Blinking Green Light on Mitsubishi DLP 52525


No problem, do self diagnosis test, read threads here or goto ctechnicians.com get error codes first and get back with me.

Dec 17, 2007 | Mitsubishi WD-62825 62" Rear Projection...

Not finding what you are looking for?
Mitsubishi WD-62525 62" Rear Projection HDTV Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1210 Answers

The Knight
The Knight

Level 3 Expert

74106 Answers

Jaime Hernandez

Level 3 Expert

2318 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...