Question about Hotpoint Aquarius WD640 Front Load Washer/Dryer

2 Answers

Aquarise + super silent WF 630 1300 spin

My washing machine has just stopped it is showing TEST and will not wash ot spin this has happened before and i was given advise how to deal with this but i was a long time ago and i have lost the details can any one help cheers sue

Posted by on

  • pvalerie126 Nov 04, 2008

    my machine keeps reading test

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers

To removed test display press and hold start/cancel button for 5 secs. then press on/off and start/cancel together until d-off is displayed then machine will work

Posted on Dec 28, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My hotpoint aquarius wf 640 was showing f-05 i unblocked the pump and now it wont spin fast the drum just goes round slow and wont empty does anyone know what it could be

Posted on Dec 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lg Fuzzy Logic 5.5kg Turbo Drum with I-sensor, Model WF-T552TH Washing machine goes through initial fill up, when changing to spin/wash works for 2 seconds, then stops spinning back and forth and shows dE...


There is a small magnet at the front of the lid that triggers the door error, mine was corroded and the lg people wanted $80 for a service fee.. Ha I went to my local hobby shop and got a small earth magnet and some super glue $1.50 later and she's fixed.. tadAaa.

May 11, 2011 | Washing Machines

1 Answer

Can a HOTPOINT ULTIMA SUPER SILENT ( WF 860 ) 1600 SPIN washing machine run off a cold fill only


The simple answer is yes, via a Y piece if it is a hot and cold fill model
The fitting is available from B&Q, or a plumbers merchants

Aug 13, 2010 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Hotpoint ultima super silent w f 840 shows fault 03


Code f03 means wash thermistor open circuit, this is normally part of the heating circuit, suggest you test heater and thermistos located in the end of the heater, and replace if necesscary. If heater o/k , then could be bad connection to control module, or broken wire, if still no joy, then call Hotpoint.
Please rate my solution.
Thanks.

May 30, 2009 | Hotpoint Ultima WF840 Front Load Washer /...

3 Answers

Error Code "TEST"


Just had the same problem & found the following solution via the web :-
1. When tESt shows hold down both the ON/OFF Button & the START Button together & let the Test proceed holding the two buttons down for the entire test (Approx 3 Minutes ) .
Continue to hold the " buttons down until the word Done appears.
After which you should be able to proceed with the normal wash cycle

May 28, 2009 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

My hotpoint ultima super silent displays 'test' but dnt run cycle


its in factory test mode, this can be set by pressing the on and start buttons together. to reset, turn on while pressing the on and start together until dOFF appears

Jan 25, 2009 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Testing Shows On Display


press and hold start/cancel button for 5 secs. Thenpress on /offbutton and start/cancel together until Doff is displayed the machine should now be ok

Nov 26, 2008 | Hotpoint Aquarius WF000 Front Load Washer

2 Answers

HOW CAN I GET MY HOTPOINT AQUARIUS 1400 - OFF CONSTANT TEST PROGRAM?


This works

To exit the TEST mode, press and hold down the "Start/Cancel" button until ALL of the console lights light up. Press both "Start/Cancel" and On/Off buttons simultaneously until " dOFF " appears in the display. The default setting will now appear and the machine can be used normally.

Feb 04, 2008 | Hotpoint Washing Machines

2 Answers

HOTPOINT ULTIMA SUPER SILENT ( WF 860 ) 1600 SPIN SPEED.


I read that someone has a problem with F-03 on the display. I have seen this for the first time on my hotpoint wf860 1600 spin. I read the manual the only thing I can think of maybe an unbalanced load in the machine. Albeit the manual is not clear about this. P21 automatic features unbalanced load warning.

Sep 04, 2006 | Hotpoint Ultima WF860 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WD640 Front Load Washer/Dryer Logo

400 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...