Question about Washing Machines

1 Answer

Water pores out on spin

On spin mode water pores out

Posted by on

  • victor montez Feb 21, 2012

    the water that pores out comes where it need to come out when it fill the tub . but on spin mode. I con open lid spin stops but water still pores out like in wash mode.

  • victor montez Feb 24, 2012

    ran wash mode found out water did not drain on rinse . It just wash untill timer got to spin mode.



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 211 Answers

Take off the cover and check for any holes in the top of the plastic tub surrounding the drum . This can occur when the washer is or was previously severely out of balance and the drum rubs a hole in the side of the tub. Since the water is usually below this level until the spin cycle pushes the water up the sides of the tub, it only becomes apparent then. Another possibility is there may be a blockage in the pump or drain hose. If you still have a good amount of water in the tub due to the washer not draining completely before the spin cycle, the water will sling everywhere when it attempts to spin. I hope this helps! Good luck!

Posted on Feb 21, 2012


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:


Skin tip -Treating Large Pores

Treating Large Pores.If you have large pores that resemble little holes on your skin, the following steps may be helpful. Stop using commercial products on your skin. Instead, use homemade skin cleansers. Splash warm water onto your face and pour half a handful of stone-ground cornmeal into your wet palm. Massage the moistened meal into your entire face area, adding water as needed. Another homemade cleanser can be made by adding a few drops of lemon or lime juice or apple cider vinegar to milk (use powdered skin milk if your skin is oily).<br />Soak yarrow (check health food stores or botanical supply stores for this herb) in water overnight, and apply this astringent several times a day - less frequently if your skin is dry.<br />Avoid all creams. Use an unsaturated vegetable oil if you need to (e.g. vitamin E oil).

on Nov 23, 2010 | Health & Beauty

2 Answers

Reset cod toshiba 306se

Everyone desires to appear the best they are able to. Though beauty is subjective, every individual has their own beliefs to strive towards. There are lots of ways one can go about receiving or strengthening their elegance with this particular having been said. Wonderful tips are contained by this
There are a few points we simply can't do on our very own therefore it may be best to visit a dermatologist faster, even though we attempted. This skin care specialist help you with issues such as having oily or dry skin and also can do miracles for the skin.

Jun 20, 2016 | Toshiba Office Equipment & Supplies

1 Answer

Only spin with water in-flow

Need some more info but it seems like control module or inlet valves, is the water coming in all the time or just in spin mode?
thanks tk

Mar 10, 2014 | Kenmore Washing Machines

2 Answers

After Im done shaving with my electric shaver, do I need to use any lotion?

In order to properly care your skin, you should use a pre-shave lotion after you done shaving. First you should rinse your face with warm water then cool water. Then, you need to par your face dry and apply an after shave balm to smooth your skin.

Feb 06, 2013 | Health & Beauty

1 Answer

My Whirlpool washer fills up but won't stop poring into the washer. Is this something that is repairable?

Your water level switch could be defective. This switch has a plastic 1/4 hose connected from your tub to the switch. (should be easy to find.) Make sure this hose is connected to your tub and switch and the line has no holes. It is easy to test the switch by disconnecting the line from the tub and while water is flowing into your washer, Blow into the line. The pressure will stop the water flow. If not, Bad level switch.
Level switch part# W10339333

Mar 28, 2012 | Whirlpool WTW5100SQ

1 Answer

My duet front load washer wont spin in drain spin mode. The drain pump goes but it wont spin. I emptied the large filter just under the door behind the front pannel, It still wont spin. Plenty of water...

If your washer doesn't drain or spin, you may read and learn what parts may cause this. First, you will want to check your water pump. You need to make sure it is working. Make sure you check the belt on the pump. Make sure it is not broken or loose. Also, make sure your pulley is not stuck in place. Sometimes, they will stick or barely turn at all. If this is the case, you will need to replace it. If the pump, pulley, and belt are working, make sure your motor is working. You should be able to hear it if it is. If it isn't, check your lid switch. The lid switch can cause the motor to not work. It may need adjusted. If not, go ahead and change it. A bad lid switch may cause the washer to not work at all. Now, if your pump is pumping and the washer still won't spin, you will want to check your belt and clutch. Once again, the belt may be broke or loose. Check to make sure your clutch is not worn also. This may be a case of a bad lid switch again as well. You could have a bad drive motor. This is what controls spinning, draining, and agitation. You could have a broken motor coupler. Over time, they will go bad and need replaced. It is possible that your transmission is slipping or damaged. And lastly, you could have a bad basket drive ir spin bearing. This is what allows the inner tub to move. If this is the case, you will probably hear loud sounds or loud banging. I want to thank you for reading and I hope this helps you. Best regards and thanks for reading

Apr 22, 2011 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

.water pores onto the ground under car 1994 sl 2

you know its not the radiator or you would have said so.the other things it could be is the water pump is leaking badly,you have a frost plug rotted out or missing,a coolant hose is split,a very bad head gasket,you will have to get under the car to see were the leak is coming from or there will be a water(coolant)stain you can follow to the leak.

Apr 19, 2011 | 1994 Saturn Sl

4 Answers

How can I make the pores on my face look smaller or even gone? My pores are really big and I find it difficult to get the look I desire.

Most enlarged pores on the face are the result of hereditary factors more than anything else. You really cannot make the pores disappear. You will have to create the illusion of a poreless complexion. Apply foundation, concealer, powder and blush in a downward motion, otherwise you'll accentuate pores by pushing color up and into them. For a temporary fix, especially for a special event, I recommend using Colosé Serum Vital Lifting. It tightens and tones the surface layer, refreshs, moisturizes and firms your skin. With the first application the skin becomes even, smooth and has a radiant appearance. The tightness last approximately 4 to 6 hours and definitely makes your pores seem much smaller or even gone. Apply before makeup and let completely dry.

Nov 23, 2010 | Health & Beauty

1 Answer

Bosch classix washer dryer has just flooded water through its door and drawer whilst on a cycle. Any suggestions?

Several possibilities.
  1. Was water poring out of the drawer when the appliance was in spin?if so then possible cause is that the appliance hasnt draqined its water first. It is trying to spin with water in drum and it has to go somewhere.
  2. Is the appliance overfilling? Water level should just come to the bottom of the door but if you see it rising up to the top of the door then you have a problem with the water level sensor (or a blockage)
From experience with the type of fault you have i would say that its not draining all the water before spin. If you have a pump out function then do this a few times until ALL the water has drained. put a large towel in front of bthe filter and unscrew filter cover and check for a blockage.
If you cant find anything then you may need to call a engineer

Hope this helps

Aardvark Repairs

Nov 16, 2009 | Bosch Classixx WVF 2402 Front Load...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers


Level 3 Expert

79847 Answers

Brad Brown

Level 3 Expert

17151 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides