Question about Heating & Cooling

Open Question

RUUD FURNACE UGPH-12EARJR - Heating & Cooling

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 18 Answers

SOURCE: I have a Ruud Silhoulette

Could be a bad fan control board or the motor. Need to see if you have power to the motor from the board

Posted on Jul 06, 2008

Ad
  • 1033 Answers

SOURCE: Need 24v fuse for Ruud Heating unit UGPH-12EARJR

Hello, these fuses are 3-5 amp and can be purchased at a heating and cooling supply store or hardware store.

Posted on Nov 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need 24v fuse for Ruud Heating unit UGPH-12EARJR


Hello, these fuses are 3-5 amp and can be purchased at a heating and cooling supply store or hardware store.

Nov 03, 2011 | Ruud UBHC Air Conditioner

1 Answer

Ruud gas Furnace UGPH 07EAUER cycles properly heats to temp and shuts down normally.....then a little while later it cycles, but does not ignite. Blower circulates cold air through the house negatiing the...


Whew...

Most likely... Your part number (look it up)

RUUD 47-25349-?? (LIKE: 02, 03, 07... etc).
(typically: $10 -$20 range... easy job)

On eBay:


A bit slow getting this answer out on the table...

Sorry anonymous.

BUT for the "over-temp" condition...
Forget the wall THERMOSTAT.
There's usually a switch to option the "DEPTH" of
your heating cycle
(Look up Owners GUIDE for your SPECIFIC MODEL).

The "cool down"... (if there is one) would more
likely be you heaters OWN (fan) THERMOSTAT...

It SHOULD not be getting that much RESIDUAL heat
(possible plenum failure... but hopefully just the switch).

Here you have to ask yourself...
Is IT TIME to get your heater
PROFESSIONALLY inspected...
Pacific Gas & Electric used to do that for FREE...
(
but in this new, improved UTILITY climate
we enjoy today... I doubt they''ll do more than TAKE OUT
a few blocks in SAN BRUNO for FREE anymore...
(you might want to check...
(Same DEDIATED workers w/ really poor Management)).

(My opinion: FAT CAT, CRONY, bought & well-paid
EVIL/corrupt Government "oversight" (CPUC)).

There SHOULD also be a HIGH TEMP
fuel shut off "SAFETY" thermostats..

All these should only be handled with skill & knowledge...
as GAS APPLIANCES can be quite dangerous in the
WRONG HANDS...!!

I am just saying...!!

I'm here daily... Comment me back if unclear.

Happy hunting.

Carnac the Magnificent Y

Mar 12, 2017 | Ruud UBHC Air Conditioner

1 Answer

Just moved into a 40 year old house that has an RUUD model UGPH-07EAMGR furnace. Went to check the filter (which of course was loaded), and it was just sitting over the insertion slot. Suspect someone put...


The duct work on the return air can be made to accommodate any size of filter and it may not be the size the furnace takes. Some installers can cut a slot in the outside of the duct and put the filter there, bypassing the manufacturers method of mounting. I would measure the slot or mounting and see what comes close.

Jul 16, 2017 | Heating & Cooling

1 Answer

My furnace comes on and heates the house for about


There is a limit switch that is likely opening. Be sure your filters are clean and all registers and grilles are open and not obstructed. If the problem continues, you may have a dirty indoor coil or undersized duct work. Some models have a window where you can observe the LED lights. If when the furnace shuts down you see any blinking, you need to count the flashes and we can figure out what the problem is from there.

May 13, 2010 | Ruud UBHC Air Conditioner

1 Answer

My furnace comes on and heates the house for about


Make sure filters are clean . if they are stopped up the unit will over heat. Lets start there. Russ

Mar 22, 2010 | Ruud UBHC Air Conditioner

1 Answer

Blower fan is not coming on


I recommend you getting service its a safety thing. the humming is the transformer and is normal.. good luck Tom

Jun 22, 2009 | Ruud UBHC Air Conditioner

1 Answer

RUUD UPGH air/furnace just quit....no response...where to begin?


is the power light on the board lit? IF NOT THE 3 AMP OR 5 AMP FUSE COULD HAVE BLOWN ON THE BOARD

Apr 27, 2009 | Heating & Cooling

1 Answer

I have a Ruud Silhoulette Model #UGPJ-12EARJR Furnace. My Carrier A/C unit comes on but the fan blower motor in the furnace does not.


Could be a bad fan control board or the motor. Need to see if you have power to the motor from the board

Jul 06, 2008 | Ruud Heating & Cooling

1 Answer

RUUD Heater and Ac MODEL #UGPH-07EAUER


It sounds like the thermostat is not functioning correctly. Has it been changed recently? I think the green wire is connected directly with red somewhere, maybe touching within the wiring in the wall. Also make sure the thermostat is set to auto not on. Sorry if you knew that but you would be surprised how many people don't.

Mar 01, 2008 | Ruud UBHC Air Conditioner

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

paulcarew

Level 3 Expert

2514 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Donni Steen

Level 3 Expert

659 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...