Question about Vacuums

Open Question

Seal A Meal VS75 - missing nozzle

My nozzle is broken! I can't find anywhere that stocks this models spare parts. Can anyone Help

Posted by on

2 Suggested Answers

SOURCE: Seal-a-meal won't seal

I put the food in the bag and place the unsealed end of bag in as
directed to seal and does not take out the air out of bag but it will seal. The motor seems to be having a hard time.

Posted on May 30, 2008

leannastewar
  • 1 Answer

SOURCE: Seal-a-meal won't seal

Take apart and see if wires are connected That is what was wrong w/ mine. Soldered wire now works fine.

Posted on Aug 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My seal a meal won't seal the bags. I have tried using premade bags and hand cut bags. It sucks the air out but will not heat up to seal.


There is either a blown fuse in the heater circuit or a bad heater filament, you can take it apart to see but there is no diagram or parts list on something like this, replace it.

Dec 09, 2016 | Vacuums

1 Answer

How can I remove the head/change the nozzle on unidentified vacuum?


Search Results

    DC28 Cleaner Head Replacement Removal - YouTube

    ? 17:19
    https://www.youtube.com/watch?v=yERbv8owKU4
    Apr 2, 2013 - Uploaded by AllVacuumBrandsCTN1
    DC28 Cleaner Head Replacement Removal ... Dyson DC28 Animal - King of Vacuum Cleaner For Pets Hair ...Missing: nozzle ‎unidentified

    Dyson DC24 - Replacing the cleaner head (Official Dyson ...

    ? 0:55
    https://www.youtube.com/watch?v=PeI8N2SuXkM
    Sep 29, 2011 - Uploaded by AskDyson
    How to replace your Dyson DC24's cleaner head. ... Our brush bar reset guide shows how to remove the ...

    How to replace a Henry floor tool on a Numatic ... - YouTube

    ? 0:47
    https://www.youtube.com/watch?v=AUEaFIIFmeg
    Apr 15, 2010 - Uploaded by eSpares
    For all your Numatic vacuum cleaner spare part go to http://bit.ly/1G0FaXS If you've cracked the floor tool ...



Jan 27, 2016 | Vacuums

1 Answer

How do i replace to nozzle/valve assembly on a hoover steamvac model F59149?


Hi James, that is the correct part for your model. I believe I have the part in stock, I will check when I get to my store, for $8.99 including shipping. I will also include installation instructions and my toll-free number if you have any questions getting the part installed.

Feb 07, 2015 | Hoover Vacuums

1 Answer

Can anyone tell me where the two rectangular magnets goes in a shark navigator vacuum. i found out that it goes next to the motor but don't know how to position them HELP!!


There are two metal weights in the power nozzle of some models but they are not magnets. They fit I the compartment between the upper and lower parts of the nozzle. Housing

Oct 22, 2013 | Vacuums

2 Answers

I broke the part that vacuums the carpet on my Electrolux cannister model EL 7020. Can it be replaced?


What you need to do is contactthe guys that make that model of vacuum, and they will either be able to help you locate a spare parts provider or they may be able to help you oredr the part you need. Good Luck.

Dec 02, 2009 | Vacuums

2 Answers

Missing parts


Contact BISSELL they should be able to get you going

Aug 28, 2009 | Bissell 1631 PowerSteamer ProHeat Canister...

1 Answer

Eureka Bravo II poor suction at hose


check if the hose is clogged or the fan is broken

Jan 04, 2009 | Eureka 7606 Bagged Upright Vacuum

2 Answers

Bissell Proheat 2x model number 9200 Sometimes it did not release water.Then today I unpluged it and went to a different room pluged in does not work tried different outlet will not turn on


These are two different problems the first could be a clogged heater soap coagulates in the heater passages and clogs the flow of water to see if this is indeed the problem turn the unit on and try and spray water with the top trigger (floor nozzle) then try to spray at the hand nozzle if you get water at the hand nozzle but not the floor nozzle it is the heater. The hand nozzle water bypasses the heater. Also check the solution or soap tank if you pull it out and there is not red seal on the bottom it may be stuck in the machine and won't create a good seal check to see if it is still in the hole where the tank inserts. As for the unit not turning on that could be a number of issues cord,switch or just over heated. Visit www.stevessewandvac.com for any parts or questions about this machine or any other.

Aug 05, 2008 | Bissell 9200 Upright Vacuum

Not finding what you are looking for?
Vacuums Logo

Related Topics:

318 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18381 Answers

D. Floyd Kolb
D. Floyd Kolb

Level 3 Expert

43501 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...