Question about Sewing Machines

Open Question

Brother nx 600 thread jam - Sewing Machines

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 323 Answers

SOURCE: Brother nx 600 bottom thread pulls out

Either the upper tension is loose or the lower tension is tight. Tighten the upper tension because it has numbers to refer to.
sewman7

Posted on Jul 12, 2008

Ad
  • 980 Answers

SOURCE: I purchased a brother nx 600 in March 2007

When you buy a computerized machine I have always though it is a gamble, you only have to look on this site to see how many people have problems and the biggest problem is getting a dealer that has the technical knowledge to repair it, I have been in the trade for 35 years and I would not touch any of them, your option is to either have it repaired or swap it in for a different make or model.

Posted on Mar 24, 2010

  • 1788 Answers

SOURCE: I have a Brother Pacesetter

Call Brother at 1-877-276-8437 tomorrow. Your manual is available for free to download at www.brother-usa.com and see if it is listed on page 146. Hope it helps you Good luck, nothing more frustrating than a sewing machine being balky.

Posted on Sep 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can the operation beep be switched off on the brother NX 400 sewing machine


Most machines have sounds that cannot be turned off. You can probably try contacting Brother support.

https://www.manualguru.com/brother/nx-400/owners-manual


https://www.manualguru.com/brother/nx-400/owners-manual

Nov 22, 2016 | Brother NX-400

1 Answer

Material will not feed after a jam while doing embroidery.


Make sure you CLEARED all the fabric and thread away from the inside of your machine. Disconnect it from the power. Then turn it back on.

Aug 10, 2014 | Brother NX-400

1 Answer

I have a Brother XR6600 - today I got an E6 error indicting tangled thread. Ihad a check and cleaned it but no thread. When I try to sew the machine jam's ..... Help!


try these things
new needle
rethread machine--presser foot & needle to highest position
keep a check on the thread take up lever, when the top thread come
off the thread take up lever it can also make the machine jam

Jun 05, 2012 | Brother Sewing Machines

1 Answer

Hello, I have a Brother NX200-Innovis computerized sewing machine. It was sewing like a dream when all of a sudden it slowed down and beeped and flashed "E6" . The balance wheel has completely...


turn the sewing machine completely off
rethread the machine the top thread & bobbin, if possible use a different spool of thread for top & bobbin
then turn the sewing machine on again & see if you still get the same message, if the same message still displays,,then it needs to be serviced

Aug 10, 2011 | Brother NX-400

1 Answer

I have a Brother Pacesetter NX 600 sewing machine. I'm getting an F04 error when I turn it on.


Call Brother at 1-877-276-8437 tomorrow. Your manual is available for free to download at www.brother-usa.com and see if it is listed on page 146. Hope it helps you Good luck, nothing more frustrating than a sewing machine being balky.

Sep 19, 2010 | Brother Sewing Machines

1 Answer

Brother nx 600 bottom thread pulls out


Either the upper tension is loose or the lower tension is tight. Tighten the upper tension because it has numbers to refer to.
sewman7

Jul 12, 2008 | Sewing Machines

1 Answer

Balance wheel is totally jammed


machine was working fine when suddenly it just jammed up. Everything seems to be fine, but the balance wheel is completely jammed rigid. I've looked at the shuttle and there are no thread jams at all. The needle moves fine from side to side with different stitch selections, but wont go up and down with the wheel.
I have tried looking in the machine, but I can't find any thread jammed.

Apr 26, 2008 | Brother NX-400

Not finding what you are looking for?
Sewing Machines Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sewing Machines Experts

Tally Girl
Tally Girl

Level 3 Expert

1129 Answers

Chris Wetmore

Level 2 Expert

185 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

Are you a Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...