Question about Denon AVR-1400 Receiver

Open Question

When i turn denon avr 1400 receiver on the standby light stays on

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 54 Answers

SOURCE: Denon AVR-1601

This is a very common problem with denon receivers of the 2001-2-3 vintage. On almost every one, there are 4 little "surge" resistors in the power supply. These werent quite robust enough from the factory and one day would just burn open for no reason. Well, actually there is a reason, the "surge" that happens every time you power the unit up eventually weakens the resistors and then they pop. You need to take this to a denon service shop as I GUARANTEE they have seen this before. They need to check resistors in the picture, locarde above the **** rectangular connector. Resistors numbers R141, 142, 148, 149: 75f69d7.jpg These resistors when measured, should be less than 10 ohms each. If they are more, then they are blown. If they are blown, then have the shop check the channels for blown output transistors. If the outputs are OK, then these resistors should be replaced with 1 ohm 1/2 watt metal -film flameproof resistors. You might need to be prepared for a large bill, because the entire unit must come apart to replace the resistors, however, just checking them takes only about 10 minutes... Good luck and don't try this at home. Rob

Posted on Apr 08, 2008

simplemitch
  • 752 Answers

SOURCE: Denon AVR-4800 5.1Channel Standby light blinking

It's going into protect. Unhook ALL the speakers and see if it still shuts itself off. If so, then it will have to be taken in for service.

Posted on Oct 27, 2007

  • 6 Answers

SOURCE: Denon AVR-1508

sounds like overload protection
turn the volume all the way down, then turn it on
if that doesn't do it you may have a short in one of the speaker lines - try disconnecting them one at a time

Posted on Jan 13, 2008

  • 5 Answers

SOURCE: Denon AVR older receiver but worked fine; now

Did you try to reset the unit? Resetting the unit has fixed every problem I have ever had......turn off unit.....hold down A+B at the same time then turn the unit back on...hold buttons for roughly 3 seconds....Let me know if it works.

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Denon AVR-75 seems to stay in standby (red standby light is on) and I don'd get surround sound through it. How do I get it out of standby?


if the receiver does not power on from standby there is a problem like bad power supply or even bad macroprocessor. You need to bring it to a service center for diagnosing. 10-years old receiver, maybe better to buy new one.

Nov 23, 2011 | Denon AVR-75

1 Answer

My Denon AVR-1804/884 standby light stays on but the receiver wil not power up


ok my denon avr 1804 was jamming and it shut off on standby red light flashing comes on then goes back off what is wrong ?????

Feb 27, 2011 | Audio Players & Recorders

1 Answer

Has power but keeps switching to standby


Disconnect all speakers at the receiver and turn it back on, if it stays on post a comment and I will help you troubleshoot further. If it still cuts out, it needs to go to service for repair. Hope this helps.

Aug 21, 2009 | Denon AVR-1907 Receiver

1 Answer

Denon AVR older receiver but worked fine; now


Did you try to reset the unit? Resetting the unit has fixed every problem I have ever had......turn off unit.....hold down A+B at the same time then turn the unit back on...hold buttons for roughly 3 seconds....Let me know if it works.

Aug 20, 2009 | Denon AVR-1908

1 Answer

Standby light stays red and will not turn unit on.


Try to reset the macroprocessor. Unplug the unit from AC, hold both buttons SPEAKER A and SPEAKER B and plug the cord in outlet. After display flashes several times release the buttons. No result? - repair shop.

Apr 05, 2009 | Denon AVR-1906 Receiver

2 Answers

Denon AVR-1500 Receiver turns on but only a red blinking light


Hi, I have a Denon arv1500 with a bad tuner. If you can't get yours fixed, would you be interested in selling it--I'd use it for parts.
If you still have it, and would be willing to sell it, let me know! denny@dennyls.com

Mar 22, 2009 | Denon AVR-1500

1 Answer

My Denon AVR5800 Receiver Shut itself off after I turned it on?


This amp is going into protect mode as it is sensing an internal overload,needs to be repaired...

Jan 08, 2009 | Denon AVR-5800 Receiver

2 Answers

Denon AVR-4800 5.1Channel Standby light blinking


It's going into protect. Unhook ALL the speakers and see if it still shuts itself off. If so, then it will have to be taken in for service.

Oct 27, 2007 | Denon AVR-4800 Receiver

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

653 people viewed this question

Ask a Question

Usually answered in minutes!

Top Denon Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5056 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

The Knight
The Knight

Level 3 Expert

74136 Answers

Are you a Denon Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...