Question about Nuvico NVJV-4000N Video Recorder

2 Answers

Motion detection problem with surveillance cameras

Help! I have been unable to get the motion alert icon to appear on any of my four channels, and the channel icon doesn't turn red and blink with motion alert. "Event" does appear on the left upper corner of my screen, but the white dot remains despite activity on my cameras. Thus I assume the DVR isn't recording the action. I followed the Nuvico instructions, but I must be doing something wrong. Thanks!

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Contributor
  • 52 Answers

Bud is correct. Also check that you are asking the DVR to record these channels. I would go through each of the settings and make sure you have enabled recording, the motion mask is correctly setup and that you have done everything that is required to start recording. You may want to reboot. Turn off DVR and unplug from power. Then reconnect and turn on. See if recording is enabled. You may want to contact Nuvico support if this does not work.

Posted on Nov 23, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Under motion settings you must select all or parts of the screen to be viewed.you may have them all unselected.

Posted on May 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get full picture on my tv?


First, ensure your tv is using the highest resolution possible (Usually 1080 for flat screens) by using an HDMI cable from the receiver to the television, and that you are on the correct input. Second, ensure your tv is not sizing the video by using the 'picture size' or 'aspect' or 'ratio' key on the remote that came with your tv (Not your DISH remote). Third, tune your DISH receiver (with your DISH remote) to an HD channel (for VIP model receivers, when you tune the channel to an HD channel, an opaque white 'HD' appears insude the blue box at the top of the screen). Fourth, hit the star key on the remote, while watching the screen. On the right hand side, near the top, it will cycle as you hit repeatedly the star key, the style of screen widening. Hit the key as often as you need to make the screen appear the way you want it to. The receiver will remember your setting for all HD channels. When finished with the HD channel, tune your receiver (with your DISH remote) to a SD channel (any channel in the guide that does not have the HD icon). Repeat the fourth step.

For Hopper/Joey family receivers, hit menu, settings, screen size. Follow the instructions to resize your screen to match your preference. When finished, repeat step four above on each an HD and a SD channel.

Mar 15, 2015 | DISH Network TV Receivers & DVRs

2 Answers

Which tv doesn't exhibit motion blur?


You want high hz(hertz refresh rate). The higher the hz refresh rate, the better motion quality. 120 hz is typical for cheaper tv's, anything above that is good, the higher the better.

Jun 14, 2014 | TV Receivers & DVRs

2 Answers

A line in the middle of my tv


If it is a plasma then chances are you have jerked it too fast or it was dropped bc the plasmas are very motion sensitive, no way to fix it just buy a new tv

Jun 19, 2013 | TV Receivers & DVRs

1 Answer

When scrolling the channels using the remote, the channels change in slow motion. The installers tell me it's because of the memory of the DVR effects the speed,,,, I have 5 movies recorded and some...


Hey Jeff this is Mike Houston of DISH Network and I have received your e-mail and I there are some things that can be done to resolve this. The first thing you will want to do is replace the batteries in the remote, and unplug the receiver for 10 seconds and plug it back in. The receiver will power back up on its own and acquire the signal and download the Program Guide, try to scroll the channels and see if it is resolved. If the issue is not resolved please e-mail me at Michael.houston@dishnetwork.com and I will assist you further.

Oct 13, 2011 | DISH Network ViP722 DTV Receiver /...

1 Answer

I get 110 direct to receiver or 119 direct to receiver (dish 500) but when I use the sw21 switch I only get one


Hi

Thanks for using FixYa. As per the issue you described, I think you are not able to switch to Channel 21. It means that it has either been deleted from the projection TV or you have set the parental control guides. To correct the former, access the Channel controls by pushing the "Menu" button and maneuver the channel icon, then press "+". Select "Favorite Channels," and then the "+" button again. Then type the number of the channel (21) you are not able to watch and press the "+" button one last time. To access the parental control channels, press "Menu" and maneuver the Parent icon, and press "+." Enter your four-digit password and use the arrows on the remote to change the overall settings. After performing this procedure hit the "+" key one more time. Now you will be able to watch channel 21 as before.

Please tell me the model number of your Unit so that I can provide you with model specific information.

Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

Sep 16, 2009 | RCA DISH Network(r) 311 Satellite System

1 Answer

I turn my monitor off and it comes back on??


I would hook it up to a different Monitor to see if your monitor is broken.

If you mean you set the screensaver in the software and it keeps turning your monitor back on, then yes, its becuase you have it set to motion detection. Thats usually called an event & systems usually come out of screensaver mode & to display the event.

Feb 20, 2009 | Lorex Dxr4280uq-a 4 Channel Digital Video...

1 Answer

I have pelco dx 2000 dvr of pelco brand i just want to know can i increase the recording days with new high rating hard drive from 90 days to 120 days


yes, on the configuratiion plage, use the schedule to increase the amount of time you want for

1) Sechedule recording
2) motion recording
3) event recording.

Remember, this is all based on the size of your hard drive and the number of camera you have installed.

Jan 14, 2009 | Pelco DX2000 Series 16-Channel 80GB DVR

2 Answers

Set HDD to master


The internal power supply to the HDD is often suspect in these units. Check you have power on the internal plug to the HDD from the circuit board. if you do not Try fitting an external HDD power supply (£15) this cured my unit which had a similar fault.
Hope this helps - good luck.

Jul 23, 2008 | Swann Communications DVR4-Alert Video...

3 Answers

Motion recording for Swann dvr4


Have you switched cameras to AUTO (A) on settings line. Is the sensitivity for motion turned on and set correctly =
1= very sensitive 9 = less sensitive.

Setting areas are shaded = no recording area
unshaded = recording area

Hope this helps - good luck.

Mar 14, 2008 | Swann Communications DVR4-Alert Video...

Not finding what you are looking for?
Nuvico NVJV-4000N Video Recorder Logo

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nuvico TV Receivers & DVRs Experts

U-Spy Store DBA Pro...
U-Spy Store DBA Pro...

Level 1 Expert

52 Answers

Phillip Hicks
Phillip Hicks

Level 3 Expert

890 Answers

SalahAddin
SalahAddin

Level 1 Expert

13 Answers

Are you a Nuvico TV Receiver and DVR Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...