Question about Durabrand DVD-1002 DVD Player

2 Answers

Manual Operation Hi. Do you know if there are any button sequences on the main unit for any type of manual operations... scene selection, ff, slow-motion, any types of these operations? Thanks, Imelda

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,794 Answers

It should work with the remote by holding the forward or revese buttons while using. To increase speed press the ff or rev buttons again.

Posted on Oct 27, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 363 Answers

Hello, everyone, have you ever played a game called RuneScape? I heard this game is very popular before, and now there are still many players, and recently I found a website may be able to help you, to share with you www.rsgoldfast.com

Posted on Dec 27, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

BO6255SS - The clock turns on but we are unable to set it and therefore cannot turn it on. Can you help?


this is as much as the manual says
After your appliance is connected to your mains supply for the
first time, the numbers on the timer display will flash. Before
you can select a cooking function or set a temperature, you
must set the appliance into manual operation mode.
o To select manual operation mode, press the manual operation
button (9) on the control panel.

http://www.manualslib.com/manual/956107/Baumatic-Bo625ss.html?page=3#manual

Jun 02, 2016 | Baumatic Ovens

1 Answer

Hi I have a panasonic split air conditioner. It turns itself off immediately after turning on, the timer button then flashes and that's all.... I have checked for an error code it is H00. I have also made...


Hi Tania,
Have you gone through this checking sequence.? it's from a Panasonic a/c manual. It could be something as simple as a clogged filter. Once you have rectified the fault, you will probably have to clear the fault code as described at bottom below, before it will condescend to work again.
David
  • Once error occurred during operation, the unit will stop its operation, and Timer LED blinks.
  • Although Timer LED goes off when power supply is turned off, if the unit is operated under a breakdown condition, the LED will ON again.
  • In operation after breakdown repair, the Timer LED will not blink. The last error code (abnormality) will be stored
    in IC memory.
14.2.2 To Make a Diagnosis

  1. 1 Timer LED starts to blink and the unit automatically stops the operation.
  2. 2 Press the CHECK button on the remote control continuously for 5 seconds.
  3. 3 "- -" will be displayed on the remote control display.
    Note: Display only for "- -" (No signal transmission, no receiving sound and no Power LED blinking)
  4. 4 Press the TIMER ? or ? button on the remote control. The code "H00" (no abnormality) will be displayed and signal will be transmit to the main unit.
  5. 5 Each press of the button (? or ?) will increase error code number and transmit error code signal to the main unit.
  6. 6 When the latest abnormality code on the main unit and code
    transmitted from the remote control are matched, Power LED will
    light up for 30 seconds and a "beep" sound (continuously for 4
    seconds) will be heard. If no codes are matched, Power LED will light up for 0.5 seconds and no sound will be heard.
  7. 7 The breakdown diagnosis mode will be canceled unless pressing the CHECK button continuously for 5 seconds or operating the unit for 30 seconds.
  8. 8 The LED will be off if the unit is turned off or the RESET button on the main unit is pressed.
14.2.3 To Display Memorized Error Code (Protective Operation)
  1. 1 Turn power on.
  2. 2 Press the CHECK button on the remote control
  3. 3 "- -" will be displayed on the remote control display. Note: Display only for "- -" (No signal transmission, no receiving sound and no Power LED blinking)
  4. 4 Press the TIMER ? or ? button on the remote control. The code "H00" (no abnormality) will be displayed
    and signal will be transmit to the main unit.
  5. 5 Each press of the button (? or ?) will increase error code number and transmit error code signal to the main
    unit.
  6. 6 When the latest abnormality code on the main unit and code transmitted from the remote control are matched,
    Power LED will light up for 30 seconds and a "beep" sound (continuously for 4 seconds) will be heard. If no
    codes are matched, Power LED will light up for 0.5 seconds and no sound will be heard.
  7. 7 The breakdown diagnosis mode will be canceled unless pressing the CHECK button continuously for 5
    seconds or operating the unit for 30 seconds.
  8. 8 The same diagnosis can be repeated by turning power on again.
14.2.4 To Clear Memorized Error Code after Repair (Protective Operation)

  1. 1 Turn power on (in standby condition).
  2. 2 Press the AUTO button for 5 seconds (a "beep" sound is heard) on the main unit to operate the unit at Forced Cooling Operation Mode.
  3. 3 Press the CHECK button on the remote control for about 1 second with a pointed object to transmit signal to
    main unit. A "beep" sound is heard, and the Error Code is cleared

Dec 10, 2014 | Panasonic Heating & Cooling

2 Answers

32" scene picture is 19" rest the scene is black


As per the operator manual in the case of the picture not showing up correctly, begin by pressing the "PICTURE SIZE" button several times to cycle through the various size options (sounds like you have tried this though). Next, press the power button first
to see if it fixes the issue... if not, then press this sequence of buttoms on the remote control (6 buttons in this sequence):
"SLEEP", "PICTURE SIZE", "[right arrow]", "[up arrow]", "[down arrow]", "[pwr button]". This restores the default screen size settings.

I am not sure how you are using your monitor (TV, HDMI, Composite, PC Monitor, etc.. ). That would be very helpful.

If this does not resolve the issue, I would suggest downloading the service manual from this link to work through the advanced troubleshooting flowchart... They point to a reinitialization of the basic functions (reset the TV to factory defaults) through the initialization process. I have worked on a number of this model, and have almost always found it is settings which have been inadvertantly mis-adjusted while tweaking preferences or the last settings of the operation since it will always go back to the last way it was setup when you power it up (no matter what modality was in use last time.. eg. 480i in PC or DVD operation changed to HDTV next time). Remember the HD 16:9 screen is nearly twice as long as the old 4:3 screens, as well as having nearly twice the vertical pixels... Thisis what it sounds like in your case with the 19" screen to me.. Let me know if this helps...

Service Manual:
http://www.buyphilipsparts.com/shop/research_new/MAG/sm/32ME303V_F7.pdf

Operator Manual:
http://www.emersonaudiovideo.com/product/product.php?id=649

Oct 10, 2014 | Emerson LF320EM4 32" 720p 60Hz Class LED...

1 Answer

Unlocking the remote and panel for Sharp Aquos LC-46LE832U 46 in. HDTV LCD TELEVISION


When all else fails read the owner manual page 35:

"• To unlock the buttons on the remote control by using the
touch sensor panel of the main unit (see page 25):
1 Press MENU to display the MENU screen, and then
press VOLl/k to select "System Options".
2 Press CHs/r to select "Operation Lock Out", and
then press INPUT.
3 Press CHs/r to select "Off", and then press INPUT.
4 Press MENU to exit.
• To unlock the buttons on the TV, press MENU on the
remote control, and then select "Off" in "Operation Lock
Out".

Took 5 minutes to find the manual for this unit. GOOGLE

Apr 05, 2012 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

1 Answer

I have a Canon W8200 and i get the error code"


Hello,
Try this:
1) As an error (E02802 or E02805 to E02809) is shown on the display, install the correct
combination of printhead and ink tanks according to the error.
2) Perform ink filling*3 following the installation sequence. After filling ink, when "Load Roll
Media" is shown on the display, turn off the power.
3) Turn on the printer while holding down the ONLINE button, ENTER button, CANCEL button,
and PAPER SOURCE button.
4) Check that "Canon W8200" is shown on the display, and then release the buttons. When
printer enters Reset mode for the dye/pigment model setting, all the LEDs on the operation
panel turn on.
5) "TYPE RESET" is shown on the display.
6) Select "YES", and then reset the dye/pigment model setting in the printer.
When reset is selected, the ink drain sequence is executed. It takes approximately 4
minutes for the process to be completed.
7) Check that "Turn Power Off!!" is shown on the display, and then turn off the power.
8) Unplug the power cord from the outlet.
9) Move the carriage, and then takeout the printhead.
10) Replace the following parts
• Ink tube unit : See "Part 5: 5.2.6 Ink tube unit".
• Purge unit : See "Part 5: 5.2.9 Purge unit".
• Ink tank unit : See "Part 5: 5.2.10 Ink tank unit".
11) Turn on the printer, and then continue with the installation operation (from installation of the
printhead). At this time, replace the printhead with a new one*4.


For service manual, You can write me on emma.servis@gmail.com

Hope that helps!

Jul 29, 2011 | Canon W8200PG InkJet Printer

1 Answer

Hi will work on gas will not work on 110


This refrigerator is equipped with a control system, which can automatically select the most suitable energy source which is available, either 120 Volt AC or LP gas operation. The refrigerator can be operated in either the AUTO mode (thermostat factory preset below the safe food storage temperature) or MANUAL mode (continuous operation - no thermostat control).

NOTE: Under certain cool weather conditions, the food in the lower portion of the fresh food compartment may freeze if operated for an extended period of time on the MANUAL mode.

A. A 12 volt DC supply must be available for the electronic control to function. The refrigerator will work down to 9.6 volt DC.

B. Press the main power ON/OFF button (1) to the DOWN position.

B. In AUTO mode operation, the temperature is controlled by a single temperature setting, on the energy source selected by the control system. (See Auto Mode)

C. In MANUAL mode operation, the refrigerator will run continuously on the energy source selected by the control system. (See Manual Mode)

In case of a problem or clarification or my solution was insufficient, don't hesitate to post me a reply.

If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

Jun 01, 2011 | Dometic RM2652 Refrigerator

1 Answer

Our Dometic RM2652 RV frig has 2 yellow lights on which are indicated to be alert lights. The frig/freezer seem to be working fine.......????? Is something about to go out on it?


The 2 yellow lites... if you would... Is there and indication by description of what those 2 lights are?

Here are the modes:

OPERATING MODES

AUTO MODE

Press the AUTO/MANUAL mode selector button (2) to the DOWN position. The AUTO mode indicator lamp (A) will illuminate.

When operating in the AUTO mode, the AUTO mode indicator lamp (A) will illuminate. The control system will automatically select between AC and GAS operation with AC having priority over GAS. If the control system is operating on AC energy and it then becomes unavailable, the system will automatically switch to

GAS. As soon as AC becomes available again the control will switch back to AC operation.

If 120 volts AC is not available, the control system will automatically switch to GAS operation. Within 45 seconds the burner should be ignited and operating normally. If unsuccessful, the CHECK indicator lamp (B) will illuminate.

To restart an ignition attempt with the CHECK lamp illuminated or to clear (turn off) the CHECK lamp, press the main power ON/OFF button to the OFF and then to the ON position. The control system will attempt a new 45 second ignition sequence.

On the initial refrigerator start-up on gas (120 volts AC is not available), it may take longer than 45 seconds to allow air to be purged from the gas line. If the refrigerator has not been used for a long time or the LP tanks have just been refilled, air may be trapped in the supply lines. To purge the air from the lines may require resetting the main power ON/OFF button (1) three of four times. If repeated attempts fail to start the LP gas operation, check to make sure that the LP gas supply tanks are not empty and all manual shutoff valves in the lines are open.

NOTE: DO NOT continue to reset GAS operation if the CHECK indicator lamp continues to be illuminated after 3 or 4 tries.

If 120 volts AC becomes available while the CHECK indicator lamp is on, the control system will switch to 120 volt AC operation, The CHECK lamp will not turn off until the main power ON/OFF button is pressed to the OFF then ON position.

In AUTO mode operation, the temperature is controlled by a single temperature setting.

MANUAL MODE

When operating in the MANUAL mode, the AUTO mode indicator lamp (A) will be off, and the refrigerator will run continuously on the energy source selected by the control system.

NOTE: The food in the lower compartment may be frozen if the refrigerator is left on "MANUAL" mode.

STANDBY MODE . .

This control system contains a feature that will continue to operate the cooling system in the event of a failure of a major operating component. If the control cannot read the temperature sensor and operate at the preset temperature, then the control will run the cooling unit like the MANUAL mode.The refrigerator will continue to operate in this mode indefinitely or until a new sensor is installed and the
system is reset.

I posted the above information from the contents of the service manual. I can help you but... at the moment for sure I have come to the conclusion that ONE of the lights your seeing is the CHECK light. The mystery is... what is the 2nd light your seeing? Manual of Stand-by?

I am pretty sure we can sort this out but... we need to really communicate clearly and well. In our posts here.

Thanks for choosing FixYa,
Kelly

Feb 14, 2011 | Dometic RM2652 Refrigerator

3 Answers

I dont know how to change the shutter speed, please help :) thank you all


Hi there,

Here is the guide on how to adjust shutter speed. Got it screen captured from your camera's manual.

Good luck and let me know if this worked for you.

c57a172.jpg

Aug 22, 2009 | Sony Cyber-shot DSC-T700 Digital Camera

1 Answer

Durabrand DVD-1002


Try using the ff buttons and the reverse buttons on the player itself. That might have a scene selection option to it.

The company that made these players went of business in November. Wal Mart is exchanging them if anything goes wrong with them.

Oct 30, 2008 | Durabrand DVD-1002 DVD Player

1 Answer

Recording


The EDSR1600 will not go into manual recording mode (by pressing the REC button on the front panel) unless all of the automatic modes are disabled and the hard drive bays are firmly pressed in and locked. Press the MENU button, select ALARM and turn everything in the OPeration column to OFF. Return to the MENU, select MOTION and also turn set all the OPerations to OFF. Return again to the main MENU and under RECORD, set ALARM RECORD OPERATION to OFF, PRE-ALARM RECORD OPERATION to OFF, and PERMANENT RECORD OPERATION to OFF. Note: Turn the JOG wheel clockwise or counter-clockwise to select an option. Press the ENTER button to confirm the option and move to the next field. Press the MENU button to enter, or return to the main MENU. Press the MENU button twice to exit the main MENU. To check if the round key locks on the front of the Hard Drive bay trays are locked, turn OFF the EDSR1600. Open (pull down) the left side front cover and gently pull up on the drive bay handles. If locked, the handles should not lift and the bays should not slide out. After your check, press the bays in firmly to ensure good seating of the Hard Drives. The ESDR1600 should now go into manual RECord if the DVR is working properly. The red REC LED should also light each time a recording is being made. If the REC LED flashes, this means the DVR is recording a field or frame of video.

Jan 26, 2007 | EverFocus EDSR1600 16 CHANNEL 160GB...

Not finding what you are looking for?
Durabrand DVD-1002 DVD Player Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Durabrand Televison & Video Experts

The Knight
The Knight

Level 3 Expert

72640 Answers

matt martin
matt martin

Level 3 Expert

1207 Answers

Jaime Hernandez

Level 3 Expert

2296 Answers

Are you a Durabrand Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...