Question about Kenmore 94812 Top Load Stacked Washer / Dryer

Open Question

Kenmore 90872 Stacked will not rinse/spin

Washer works fine up to rinse cycle, empties wash water, then stops. I can hear it clicking as though to advance but no action. It is not load issue as I have taken clothes out. I tried all cycles and none will rinse or spin.

Posted by on

5 Suggested Answers

SOURCE: Kenmore stacked washer/dryer

ok, Timer has to be replaced

Posted on Jan 22, 2008


  • 1937 Answers

SOURCE: our Kenmore wahing Machine just shut down in the mddle of a cycle

This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part and only requires you to access the console and remove the cabinet.

Posted on May 01, 2010

blueextc3221
  • 15935 Answers

SOURCE: kenmore 417.4304220 starts, runs though never

Yep - change it.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Posted on Sep 10, 2010

blueextc3221
  • 15935 Answers

SOURCE: My Kenmore 110.20702991 washer stopped halfway through rinse cycl

It appears your timer/main controller/CCU has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Posted on Sep 15, 2010

blueextc3221
  • 15935 Answers

SOURCE: kenmore washer won't fill for rinse cycle on any setting

It appears your timer/main controller/CCU has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Posted on Sep 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore Washer Doesn't Agitate


Don't be too sure the drive coupler hasn't failed or is failing

Jun 15, 2013 | Kenmore 24032\24036 Top Load Washer

1 Answer

Washer stopped during spin cycle


Hello, try to checked the pump filter, and the pump is actually working. then I would suspect a draining problem.
If filter clean and pump works fine then it could be a control module fault. if this were the case, then it would probably be wiser to purchase a new washer.
Thanks

Jun 04, 2010 | Whirlpool LTE5243D Top Load Stacked...

1 Answer

Won't complete cycle, stops at rinse. and can't get hot water.


Are you on well water? turn off the cold water to the washer and clean the screen filter out. do not leave filter out.
the machine probably has a cold only final rinse so it won't work properly.

Mar 22, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore front-load washer stops at rinse cycle


When the washer initially fills for the wash, is it only hot water entering the drum? Try switching the water temperature between hot and cold as it fills. If any of them show little or no water getting through, it sounds too easy but check to make sure water supply taps are on, and that the cold/hot fill hoses aren't reversed. Remove the fill hoses and check any of the screen filters for blockage (in the hoses and in the inlet water valve). When the machine stops and waits to fill but all you hear is a hum, it sounds like there is power going to the valve but water is not able to get through it.
Good luck!

Mar 03, 2009 | Kenmore 43142 Front Load Washer

1 Answer

Kenmore stackable washer and dryer


check the belt, pulley, & idler pulley assy.

Jul 20, 2008 | Kenmore 98702 Stacked Washer/Dryer

1 Answer

Kenmore stack washer and dryer


gabehart....sounds like belt is slipping. Replace it. The water pump is on a separate smaller motor so is not affected by the agitator/spin motor.

Jun 04, 2008 | Kenmore 98702 Stacked Washer/Dryer

Not finding what you are looking for?
Kenmore 94812 Top Load Stacked Washer / Dryer Logo

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Archaeology
Archaeology

Level 3 Expert

662 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...